SolarEdge SE Series Manuel utilisateur

Installation Guide

Three Phase Inverter with

SetApp Configuration

PN: SEXXK-XXXXIXXXX

For Europe and APAC

Version 1.0

Disclaimers

Important Notice

No part of this document may be reproduced, stored in a retrieval system or

transmitted, in any form or by any means, electronic, mechanical, photographic,

magnetic or otherwise, without the prior written permission of SolarEdge Inc.

The material furnished in this document is believed to be accurate and reliable.

However, SolarEdge assumes no responsibility for the use of this material. SolarEdge

reserves the right to make changes to the material at any time and without notice. You

may refer to the SolarEdge web site (www.solaredge.com) for the most updated version.

All company and brand products and service names are trademarks or registered

trademarks of their respective holders.

Patent marking notice: see http://www.solaredge.com/patent

The general terms and conditions of delivery of SolarEdge shall apply.

The content of these documents is continually reviewed and amended, where

necessary. However, discrepancies cannot be excluded. No guarantee is made for the

completeness of these documents.

The images contained in this document are for illustrative purposes only and may vary

depending on product models.

Disclaimers 1

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

Emission Compliance

This equipment has been tested and found to comply with the limits applied by the

local regulations.

These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, you are encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance may void the user’s authority to operate the equipment.

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

2 Emission Compliance

Revision History

Version 1.0 (Dec. 2020)

Initial release

Revision History 3

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

Contents

Disclaimers 1

Important Notice 1

Emission Compliance 2

Revision History 3

Contents 4

HANDLING AND SAFETY INSTRUCTIONS 6

Safety Symbols Information 6

IMPORTANTSAFETYINSTRUCTIONS 7

Chapter 1: Introducing the SolarEdge Power Harvesting System 9

Power Optimizer 9

Inverter 9

Designer 10

Monitoring Platform 10

SetApp 10

Installation Procedures 10

Installation Equipment List 10

Inverter Transport and Storage 11

Chapter 2: Installing the Power Optimizers 12

Safety 12

Installation Guidelines 14

Step 1: Mounting the Power Optimizers 17

Step 2: Connecting a PV module to a Power Optimizer 17

Step 3: Connecting Power Optimizers in Strings 18

Step 4: Verifying Proper Power Optimizer Connection 19

Step 5: Connecting the Strings to a Combiner Box 20

Chapter 3: Installing the Inverter 21

Inverter Package Contents 21

Identifying the Inverter 21

Inverter and DC Safety Unit Interfaces 21

Mounting the Inverter 27

Chapter 4: Connecting AC and PVStrings to the Inverter 32

Grid Connection Guidelines 32

Connecting the ACGrid to the Inverter or to the DC Safety Switch 33

Connecting the PV Strings to the Inverter 36

Selecting a Residual Current Device (RCD) 39

Chapter 5: Activating, Commissioning and Configuring the System 40

Step 1: Activating the Installation 40

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

4 Contents

Step 2: Commissioning and Configuring the Installation 41

Step 3: Verifying Proper Activation and Commissioning 42

Reporting and Monitoring Installation Data 43

Chapter 6: Setting Up Communication with the Monitoring Platform 46

Communication Options 46

Communication Connectors 48

Removing the Inverter Cover 49

Removing the DC Safety Unit Cover (if applicable) 49

Creating an Ethernet (LAN) Connection 50

Creating an RS485 Bus Connection 54

RS485 Bus Configuration 57

Verifying the Connection 57

Signaling Options 58

Appendix A: Errors and Troubleshooting 60

Identifying Errors 60

Troubleshooting Communication 61

Power Optimizer Troubleshooting 62

Appendix B: Adding Optional Components 64

RS485 Surge Protection Device (SPD) Plug-in 64

AC Surge Protection Device (SPD) 64

Appendix C: SafeDC™ 65

Appendix D: Mechanical Specifications 66

Dimensions of Three Phase Inverter 66

Dimensions of Three Phase Inverter with DC Safety Unit 67

Dimensions of Inverter Mounting Bracket 68

Technical Specifications - Three Phase Inverters for Europe &APAC for

220/380V, and 230/400V Grids 69

SE25K, SE27.6K, SE30K, SE33.3K 69

Three Phase Inverter for the 277/480V Grid - SE33.3K, SE40K 73

Support Contact Information 77

Contents 5

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

HANDLING AND SAFETY INSTRUCTIONS

During installation, testing and inspection, adherence to all the handling and safety

instructions is mandatory. Failure to do so may result in injury or loss of life and

damage to the equipment.

Safety Symbols Information

The following safety symbols are used in this document. Familiarize yourself with the

symbols and their meaning before installing or operating the system.

WARNING!

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, could result in injury or loss of life. Do not proceed

beyond a warning note until the indicated conditions are fully understood and

met.

CAUTION!

Denotes a hazard. It calls attention to a procedure that, if not correctly

performed or adhered to, could result in damage or destruction of the

product. Do not proceed beyond a caution sign until the indicated conditions

are fully understood and met.

NOTE

Denotes additional information about the current subject.

IMPORTANTSAFETYFEATURE

Denotes information about safety issues.

Disposal requirements under the Waste Electrical and Electronic Equipment (WEEE)

regulations:

NOTE

Discard this product according to local regulations or send it back to SolarEdge.

HANDLING AND SAFETY INSTRUCTIONS 6

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

IMPORTANTSAFETYINSTRUCTIONS

SAVETHESEINSTRUCTIONS

WARNING!

The inverter cover must be opened only after switching the inverter ON/OFF/P

switch located at the bottom of the inverter to OFF. This disables the DC voltage

inside the inverter. Wait five minutes before opening the cover. Otherwise, there

is a risk of electric shock from energy stored in the capacitors.

WARNING!

Before operating the inverter, ensure that the inverter AC power cable and wall

outlet are grounded properly. This product must be connected to a grounded,

metal, permanent wiring system, or an equipment-grounding conductor must

be run with the circuit conductors and connected to the equipment grounding

terminal or lead on the product.

WARNING!

Opening the inverter and repairing or testing under power must be performed

only by qualified service personnel familiar with this inverter.

WARNING!

The inverter input and output circuits are isolated from the enclosure. This

system does not include an isolation transformer and should be installed with

an ungrounded PV array in accordance with the requirements of NEC Articles

690.35 and 690.43 National Electric Code, ANSI/NFPA 70, 2011 (and Canadian

Electrical Code, Part I, for installations in Canada).

Equipment grounding is the responsibility of the installer and must be

performed in accordance with all applicable Local and National Codes.

WARNING!

Do not touch the PV panels or any rail system connected when the inverter

switch is ON, unless grounded.

WARNING!

SafeDC complies with IEC60947-3 when installing the system with a worst case

SafeDC voltage (under fault conditions) < 120V.

The worst case voltage is defined as: Voc,max+ (String Length-1)*1V, where:

Voc,max = Maximum Voc (at lowest temperature) of the PV modules in the

string (for a string with multiple modules, use the max value)

String Length = number of power optimizers in the string

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

7 IMPORTANTSAFETYINSTRUCTIONS

CAUTION!

This unit must be operated according to the technical specification datasheet

provided with the unit.

CAUTION!

HEAVY OBJECT. To avoid muscle strain or back injury, use proper lifting

techniques, and if required - a lifting aid.

NOTE

Use PV modules rated according to IEC 61730 class A.

NOTE

The symbol appears at grounding points on the SolarEdge equipment. This

symbol is also used in this manual.

NOTE

A SolarEdge inverters can be installed in sites with an alternative power source

such as a generator. SolarEdge requires installing a physical or electronic

interlock, which will signal to the inverter when the grid has been

disconnected. Interlock procurement, installation, maintenance and support

are the responsibility of the installer. Damage to the inverter due to incorrect

interlock installation or use of an interlock that is incompatible with the

SolarEdge system will render the SolarEdge warranty invalid.

For more information on connecting an alternative power source

to SolarEdge inverter, refer to

https://www.solaredge.com/sites/default/files/se-inverter-

support-of-voltage-sources.pdf.

NOTE

The following warning symbols appear on the inverter warning label:

Risk of electric shock

Risk of electric shock from energy stored in the capacitor. Do not

remove cover until 5 minutes after disconnecting all sources of

supply.

Hot surface – To reduce the risk of burns, do not touch.

IMPORTANTSAFETYINSTRUCTIONS 8

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

Chapter 1: Introducing the SolarEdge Power

Harvesting System

The SolarEdge power harvesting solution maximizes the power output from any type of

solar photovoltaic (PV) installation while reducing the average cost per watt. The

following sections describe each of the system’s components.

Figure 1: The SolarEdge power – harvesting system components

Power Optimizer

The power optimizers are DC-DC converters connected to PV modules in order to

maximize power harvesting by performing independent Maximum Power Point

Tracking (MPPT) at the module level.

Each power optimizer also transmits module performance data over the DC power line

to the inverter.

Inverter

The inverter efficiently converts DC power from the modules into AC power that can be

fed into the main ACservice of the site and from there to the grid. The inverter also

receives the monitoring data from each power optimizer and transmits it to a central

server (the monitoring platform; requires Internet connection).

Three Phase Inverter with SetApp Configuration PN: SEXXK-XXXXIXXXX

9 Chapter 1: Introducing the SolarEdge Power Harvesting System

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SolarEdge Onduleur

SolarEdge

SolarEdge SE K Series Manuel utilisateur

SolarEdge

SolarEdge SE9KUS Manuel utilisateur

SolarEdge

SolarEdge BI-EU1P Manuel utilisateur

SolarEdge

SolarEdge SE K Series Manuel utilisateur

SolarEdge

SolarEdge SE15K Manuel utilisateur

SolarEdge

SolarEdge SE8k Manuel utilisateur

SolarEdge

SolarEdge 2.2KW Manuel utilisateur

SolarEdge

SolarEdge SE3000US Manuel utilisateur

SolarEdge

SolarEdge Home Battery 48V Manuel utilisateur

SolarEdge

SolarEdge SE K Series Manuel utilisateur

SolarEdge

SolarEdge SE12.5k Manuel utilisateur

SolarEdge

SolarEdge Home Hub Inverter Three Phase Manuel utilisateur

SolarEdge

SolarEdge SEK-AU I Series Manuel utilisateur

SolarEdge

SolarEdge StorEdge SE5K-RWS Manuel utilisateur

SolarEdge

SolarEdge SE330K Manuel utilisateur

SolarEdge

SolarEdge storedge Manuel utilisateur

SolarEdge

SolarEdge SE15K-AU Manuel utilisateur

SolarEdge

SolarEdge StorEdge SE5K Manuel utilisateur

SolarEdge

SolarEdge StorEdge SE7600A-US1 Manuel utilisateur

SolarEdge

SolarEdge SE8000H-AU Manuel utilisateur

SolarEdge

SolarEdge StorEdge Interface SESTI-S4 Manuel utilisateur

SolarEdge

SolarEdge SE12.5k Manuel utilisateur

SolarEdge

SolarEdge P300 Manuel utilisateur

SolarEdge

SolarEdge T568B Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur