Solace SIC3-RFK Manuel utilisateur
INSTALLATION
GUIDE
MODEL
MODULE
DIAGNOSTICS
PROGRAMMING
solaceremotestarters.com REV112316
SIC3-RFK
RED LED (FLASHING / ON)
1x / Sec. Power On
On Ignition On (Data / Analog)
WHITE LED (FLASHING)
1x Data communication from connected
device (after remote function or status from car).
2x - 4x Programming
DATA PROTOCOL SELECTION
1 Leave Ignition in OFF position
2 Press programming button (antenna button) 8x within 10 seconds (White LED on SIC3-RFK
flash 1x)
3 Choose your protocol below by pressing the programming button:
Option 2 - Press 2x - iData Telematics (Default)
Option 4 - Press 4x - iData / Fortin RF
Option 6 - Press 6x - D2D
Option 8 - Press 8x - Future Use
4 After 5 seconds White LED will flash according your selection.
REMOTE PROGRAMMING
1 Turn Igntion ON-OFF-ON (Analog Ignition connection may be required)
2 Press and hold the programming button (White LED will illuminate on SIC3-RFK)
3 After 3 Seconds the White LED will flash 1x. Release antenna button and press Lock on each
transmitter to be programmed. (White LED on SIC3-RFK flash 1x for each remote programmed)
4 Turn Ignition to OFF
(When using iData/Fortin RF protocol, the Solace remotes need to be programmed to bypass module. See
manufacturer's guide for details)
A
B
LED’S
C
D
CONNECTOR A (BLACK 4 PIN)
TO BYPASS MODULE OR REMOTE STARTER
TO SOLACE ANTENNA ( NOT INCLUDED )
GRAY / BLACK - START / STOP (-)
PINK - IGNITION INPUT (+)
WHITE / BLACK - TRUNK RELEASE (-)
RED - 12V INPUT (+)
BLACK - CHASSIS GROUND (-)
BLUE - UNLOCK (-)
GREEN - LOCK (-)
CONNECTOR B (WHITE 4 PIN)
CONNECTOR C (BLUE 5 PIN)
CONNECTOR D (WHITE 2 PIN)
BRIDGEWORK
SIC3-RFK & AUTOCONNECT
When adding an Autoconnect with this module, swapping the RX / TX lines on supplied cable(s)
may be required depending on installation. See image below
Connect SIC3-RFK to one of the data ports on the IC3 supplied with Autoconnect.
MORE INFO
INSTALL GUIDES & BYPASS MODULES
When using the SIC3-RFK in conjunction with a remote starter and/or bypass module please visit
www.solaceremotestarters.com/manuals for a complete guide on how to program and connect
the units together.
INSTALLATION
GUIDE
MODEL
OPTIONS
MENU 1*
1-01 Ignition Locks
Option 1 Option 2 Option 3
1-02 Lock / Unlock Options
1-03 Lock Pulse Timing
1-04 Unlock Pulse Timing
1-05 Trunk Pulse Timing
1-07 Park Light Output
1-08 Start / Stop Pulses
1-09 Auxiliary Timing
1-10 Auxiliary Timing
Enabled
Both 1x
0.8 Secs.
0.8 Secs.
0.8 Secs
On
1x On / Off
0.8 Secs
0.8 Secs
Disabled
Lock x1 / Unlock x2
100 mS
100 mS
100 mS
Off
2x On / Off
Latched
Latched
Unlock Only
Lock x2 / Unlock x1
3 Seconds
3 Seconds
3 Seconds
3x On / Off
2 Secs.
2 Secs.
Option 4
Lock x2 / Unlock x2
8 Seconds
8 Seconds
8 Seconds
4 Secs.
4 Secs.
solaceremotestarters.com REV112316
SIC3-RFK
Menu 2*
2-01 Start / Stop Output
Option 1 Option 2-8
2-02 Lock Output
2-03 Unlock Output
2-04 Trunk Output
Start / Stop
Lock
Unlock
Trunk Release
See Table
See Table
See Table
See Table
*Programming must be done with the SHHP-BT
Option 2 Park Lights ( - )
Option 3 Horn ( - )
Option 4 GWA ( - )
Option 5 Aux 1 ( - )
Option 6 Aux 2 ( - )
Option 7 Disarm ( - )
Option 8 Rearm ( - )
INSTALLATION
GUIDE
MODEL
CONNECTIONS
solaceremotestarters.com REV112316
SIC3-RFK & EVO-ONE
PROGRAMMING
MODULE
PROGRAM SIC3-RFK DATA PROTOCOL TO OPTION 4 - IDATA / FORTIN RF
1 Run FlashLink Manager, plug in EVO-ONE
2 Click Toggle to switch to Remote Starter Connection
3 Click Configuration, then select Options
4 Under RF Kits select Fortin 2
5 Click on “SAVE”
PROGRAMMING
PROGRAMMING REMOTES
1 Follow programming guide to program remotes to SIC3-RFK
2 Program remotes to EVO-ALL following instructions below
PROGRAMMING REMOTE TRANSMITTER(S)
STEP 1STEP 2STEP 3STEP 4STEP 5STEP 6
x5 x1
1 32 4
Download the specic vehicle
installation guide, user guide or the
latest quick installation guide at:
WWW.FORTIN.CA
On each transmitter press
lock button. The LED will
stop ashing conrming
programming
Press and release the valet switch
ve times.
The parking lights will ash and the
horn/siren wil chirp each time to
conrm.
The system can learn up to a maximum
of 4 transmitters. When a 5th
transmitter is learned the the 1st
remote is erased (FIFO).
Press and hold the valet
switch until the parking
light turn ON, the horn/
siren will chirp once.
Press and release
the brake pedal
once
Turn the
Ignition ON.
Turn the
Igntion OFF
to exit
programming
*Ignition supported through data
x1
PROGRAMMING
PROGRAMMING REMOTES
1 Follow programming guide to program remotes to SIC3-RFK
2 Program remotes to EVO-ALL following instructions below
INSTALLATION
GUIDE
MODEL
CONNECTIONS
solaceremotestarters.com REV112316
SIC3-RFK & EVO-ALL (STANDALONE FW.)
PROGRAMMING
MODULE
PROGRAM SIC3-RFK DATA PROTOCOL TO OPTION 4 - IDATA / FORTIN RF
1 Run FlashLink Manager, plug in EVO-ALL
2 Click on “EVO-ALL OPTIONS” Tab
3 Activate “SUPPORTED RF KITS” and Option “H2”
4 Click on “SAVE OPTIONS”
5 Wait for “Options Saved” Message to appear.
RED - 12V+
BLACK - GROUND (-)
*Not required when using a T-Harness
(use datalink cable supplied with EVO)
1 To program remotes to the EVO-ALL, Press and hold the FORTIN programming button. Insert the 4‐Pin (Data‐Link)
connector. Release the programming button when the LED’s are BLUE AND RED.
2 Press and hold the FORTIN programming button again for 5 seconds (Blue and Red will go Off and back On after 5
seconds). Turn ignition On, the Yellow LED will turn On.
3 Press the LOCK button on remotes you wish to program one at a time. All remotes must be program at the same
time. The BLUE and RED LED’s will flash once to confirm each remote is coded.
4 Turn Ignition OFF
*Ignition supported through data
INSTALLATION
GUIDE
MODEL
CONNECTIONS
solaceremotestarters.com REV112316
SIC3-RFK & iDATASTART HC
*Ignition supported through data
**
PROGRAMMING
PROGRAMMING REMOTES
1 Follow programming guide to program remotes to SIC3-RFK
2 There is no other programming required.
PROGRAM SIC3-RFK DATA PROTOCOL TO OPTION 2 - IDATA TELEMATICS
1 Open “Weblink Program”
2 Choose Year / Make / Model
3 Select iDatastart RF Kit & Drone
4 Configure module and Flash firmware
NOTES
**IMPORTANT - DATA CABLE MODIFICATION REQUIRED
1 Please see diagram below on how to modify SIC3-RFK cable for functionality.
Swap the BLUE & WHITE wires on one end of the cable or cut and reconnect.
PROGRAMMING
MODULE
INSTALLATION
GUIDE
MODEL
CONNECTIONS
solaceremotestarters.com REV112316
SIC3-RFK & iDATASTART (BM & BZ)
PROGRAMMING
PROGRAMMING REMOTES
1 Follow programming guide to program remotes to SIC3-RFK
2 There is no other programming required.
PROGRAMMING
MODULE
PROGRAM SIC3-RFK DATA PROTOCOL TO OPTION 2 - IDATA TELEMATICS
1 Open “Weblink Program”
2 Choose Year / Make / Model
3 Select Drone telematics kit.
4 Configure module and Flash firmware
NOTES
**IMPORTANT - DATA CABLE MODIFICATION REQUIRED
1 Please see diagram below on how to modify SIC3-RFK cable for functionality.
Swap the BLUE & WHITE wires on one end of the cable or cut and reconnect.
*Ignition supported through data
**
INSTALLATION
GUIDE
MODEL
CONNECTIONS
solaceremotestarters.com REV112316
SIC3-RFK & iDATASTART (CLASSIC)
PROGRAMMING
PROGRAMMING REMOTES
1 Follow programming guide to program remotes to SIC3-RFK
2 There is no other programming required.
PROGRAMMING
MODULE
PROGRAM SIC3-RFK DATA PROTOCOL TO OPTION 2 - IDATA TELEMATICS
1 Open “Weblink Program”
2 Choose Year / Make / Model
3 Select Drone telematics kit.
4 Configure module and Flash firmware
NOTES
**IMPORTANT - DATA CABLE MODIFICATION REQUIRED
1 Please see diagram below on how to modify SIC3-RFK cable for functionality.
Swap the BLUE & WHITE wires on one end of the cable or cut and reconnect.
*Ignition supported through data
**
PROGRAMMING
PROGRAMMING REMOTES
1 Follow programming guide to program remotes to SIC3-RFK
2 There is no other programming required.
PROGRAMMING
MODULE
PROGRAM SIC3-RFK DATA PROTOCOL TO OPTION 2 - IDATA TELEMATICS
1 Open “Weblink Program”
2 Choose Year / Make / Model
3 Select Drone telematics kit.
4 Configure module and Flash firmware
INSTALLATION
GUIDE
MODEL
CONNECTIONS
solaceremotestarters.com REV112316
SIC3-RFK & ADS-ALCA (R.S. FW.)
RED - 12V+
BLACK - GROUND (-)
YELLOW - IGNITION
YELLOW - IGNITION
INSTALLATION
GUIDE
MODEL
CONNECTIONS
solaceremotestarters.com REV112316
SIC3-RFK & DEI (4X10/5X10)
PROGRAMMING
PROGRAMMING REMOTES
1 Follow programming guide to program remotes to SIC3-RFK
2 There is no other programming required.
PROGRAMMING
MODULE
PROGRAM SIC3-RFK DATA PROTOCOL TO OPTION 6 - D2D
1 Open “XK Loader”
2 Choose Year / Make / Model
3 Configure Module features
4 Enable “SMART START” without RF
5 Flash Firmware
NOTES
**IMPORTANT - DATA CABLE MODIFICATION REQUIRED
1 Please see diagram below on how to modify SIC3-RFK cable for functionality.
Swap the BLUE & WHITE wires on one end of the cable or cut and reconnect.
INSTALLATION
GUIDE
MODEL
CONNECTIONS
solaceremotestarters.com REV112316
SIC3-RFK & DEI (DBALL RSR FW.)
YELLOW - IGNITION
PROGRAMMING
PROGRAMMING REMOTES
1 Follow programming guide to program remotes to SIC3-RFK
2 There is no other programming required.
PROGRAMMING
MODULE
PROGRAM SIC3-RFK DATA PROTOCOL TO OPTION 6 - D2D
1 Open “XK Loader”
2 Choose Year / Make / Model
3 Configure Module features
4 Enable “SMART START” without RF
5 Flash Firmware
NOTES
**IMPORTANT - DATA CABLE MODIFICATION REQUIRED
1 Please see diagram below on how to modify SIC3-RFK cable for functionality.
Swap the BLUE & WHITE wires on one end of the cable or cut and reconnect.
Ce manuel convient aux modèles suivants
10
Autres manuels Solace Démarreur à distance
