Softing TH LINK PROFINET Manuel utilisateur

TH LINK PROFINET

Installation Manual

Version: EN-012017-2.00

The information contained in these instructions corresponds to the technical status at the time of printing of it and is passed on with the

best of our knowledge. The information in these instructions is in no event a basis for warranty claims or contractual agreements

concerning the described products, and may especially not be deemed as warranty concerning the quality and durability pursuant to Sec.

443 German Civil Code. We reserve the right to make any alterations or improvements to these instructions without prior notice. The

actual design of products may deviate from the information contained in the instructions if technical alterations and product improvements

so require.

It may not, in part or in its entirety, be reproduced, copied, or transferred into electronic media.

Disclaimer of liability

Softing Industrial Automation GmbH

Richard-Reitzner-Allee 6

85540 Haar / Germany

http://industrial.softing.com

The latest version of this manual is available in the Softing download area at: http://industrial.softing.com/en/downloads.html

+ 49 89 4 56 56-0

+ 49 89 4 56 56-488

info.automation@softing.com

support.aut[email protected]

Table of Contents

Chapter 1 ............................................................................................ 5

Introduction

...................................................................................................................... 5

1.1 About TH LINK

...................................................................................................................... 5

1.2 Intended Use

...................................................................................................................... 5

1.3 Before you connect TH LINK

...................................................................................................................... 6

1.4 Conventions used

...................................................................................................................... 7

1.5 Delivery scope

...................................................................................................................... 7

1.6 Document history

...................................................................................................................... 7

1.7 Configuration requirements

...................................................................................................................... 8

1.8 Network presettings

Chapter 2 ............................................................................................ 8

TH LINK design

...................................................................................................................... 8

2.1 Connections and display elements

...................................................................................................................... 9

2.2 Mounting

...................................................................................................................... 10

2.3 SD card

Chapter 3 ............................................................................................ 10

Start-up guideline

Chapter 4 ............................................................................................ 10

Mount/unmount device

...................................................................................................................... 10

4.1 Mount device

...................................................................................................................... 11

4.2 Unmount device

Chapter 5 ............................................................................................ 11

Connect to network

Chapter 6 ............................................................................................ 13

Connecting power supply and relay contact

Chapter 7 ............................................................................................ 13

Configuring the device in the network

...................................................................................................................... 14

7.1 Connection in a network with DHCP server (Dynamic Host Configuration

Protocol)

...................................................................................................................... 14

7.2 Connection in a network with manual IP address assignment

...................................................................................................................... 14

7.3 Setting new IP and network address

...................................................................................................................... 16

7.4 Check the connection to the device

Chapter 8 ............................................................................................ 16

Network overview

Chapter 9 ............................................................................................ 17

...................................................................................................................... 17

9.1 Login

...................................................................................................................... 17

9.2 Logout

Chapter 10 ............................................................................................ 18

Settings pages

...................................................................................................................... 18

10.1 TH LINK

.................................................................................................................. 19

User administration - change password10.1.1

.................................................................................................................. 19

TH LINK description10.1.2

Table of Contents

.................................................................................................................. 19

Network configuration10.1.3

...................................................................................................................... 19

10.2 TH SCOPE

.................................................................................................................. 20

Measurement10.2.1

.................................................................................................................. 20

Alert10.2.2

.................................................................................................................. 21

Parameter distribution10.2.3

..................................................................................................... 21

Set parameter provider

10.2.3.1

..................................................................................................... 21

Apply parameters

10.2.3.2

..................................................................................................... 22

Parameters

10.2.3.3

Chapter 11 ............................................................................................ 22

Firmware update

Chapter 12 ............................................................................................ 23

Blacklist

Chapter 13 ............................................................................................ 24

Troubleshooting

Chapter 14 ............................................................................................ 24

Technical Data

Chapter 1 - Introduction

1Introduction

1.1 About TH LINK

What is TH LINK?

TH LINK TH LINK provides a secure access to the fieldbus network and forms the basis for the

Softing product TH SCOPE.

TH LINK can easily be assembled/installed and is easy to put into operation. Integrated websites

allow to configure the product without using additional software. The delivered default

configuration allows start-up in only a few minutes. In order to prevent network disruptions by

unauthorized configuration changes, all configuration functions are protected by user

administration.

Features

Secure access to the PROFINET network

Basis for TH SCOPE

Access protection through integrated user administration

1.2 Intended Use

The device is designed to be used as a secure access point to PROFINET networks. Any other use is

deemed non-intended use.

1.3 Before you connect TH LINK

Strictly observe the following safety instructions before connecting the TH LINK:

Note

Small objects or liquids must not enter the case of the TH LINK (e.g. through the ventilation

slots). This may damage the device.

Never cover the ventilation slots on the device.

Note

Never open the case of the TH LINK or carry out any mechanical modifications on the

device. This may lead to damages on the device as well as to loss of warranty.

EMC note

The TH LINK contains electronic components sensitive to electrostatic discharges. Damages

due to electrostatic discharge can lead to premature failure of components or intermittent

faults at a later stage. Before installing the TH LINK, divert the electrostatic discharge away

from your body and the tools used.

Carefully plan the integration of the TH LINK into an existing system and ensure proper function of

the system after installation.

TH LINK PROFINET - Installation Manual

The TH LINK may only be installed or uninstalled by qualified, trained electrical engineering

personnel. When installing the TH LINK, observe the regulations for handling electric components in

accordance with VDE 0100. In addition, you must also observe the valid safety and accident

prevention regulations (UVV) when operating the device within the jurisdiction of the Federal

Republic of Germany.

Always install the device on a suitable top-hat rail (mounting rail).

Cables used for the connection must not apply any mechanical forces to the device.

High temperature differences between the storage site and installation site can result in

condensation within the case, which may cause the TH LINK to become damaged. In case of high

temperature differences, wait at least three hours before operating the device.

WEEE

Electrical and electronic equipment must be disposed of separately from normal waste

at the end of its operational lifetime.

Please dispose of this product according to the respective national regulations or

contractual agreements. If there are any further questions concerning the disposal of

this product, please contact Softing Industrial Automation.

1.4 Conventions used

The following conventions are used throughout Softing customer documentation:

Keys, buttons, menu items, commands and

other elements involving user interaction are

set in bold font and menu sequences are

separated by an arrow

Open Start Control Panel Programs

Buttons from the user interface are enclosed in

brackets and set to bold typeface

Press [Start] to start the application

Coding samples, file extracts and screen output

is set in Courier font type

MaxDlsapAddressSupported=23

Filenames and directories are written in italic

Device description files are located in C:

\<Application name>\delivery\software

\Device Description files

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

Note

This symbol is used to call attention to notable information that should be followed during

installation, use, or servicing of this device.

Hint

This symbol is used when providing you with helpful user hints.

Chapter 1 - Introduction

1.5 Delivery scope

TH LINK PROFINET includes

TH LINK

Installation Manual

Release Note

You can find software and documentation in our download area at http://industrial.softing.com/en/

downloads.html.

1.6 Document history

Document version

Release date

Modifications compared to previous version

1.00

December 2014

Adaptation to new Softing documentation

structure and layout

1.10

April 2015

New section "SD card".

Startup guideline enhanced with SD card

functionality.

New setting Data restore after voltage recovery

added to section TH SCOPE.

Hint in section Technical data added when using

an SD card.

1.20

July 2016

New Corporate Identity implemented

2.00

January 2017

New network overview tab TH LINK

HTML 5 Graphical User Interface for TH LINK

1.7 Configuration requirements

(not included in the scope of delivery)

Webbrowser with Adobe Flash Player 10.0 or higher

The following ports have to be enabled in the firewall:

Protocol/purpose

Port

HTTP

80 TCP

Firmware update

1100 TCP

TH LINK communication with each other

1123, 1124, 2364 UDP

TH LINK communication with TH SCOPE

via Multicast

via Unicast

2364 UDP

1151, 2365, UDP

TH LINK PROFINET - Installation Manual

1.8 Network presettings

The device is preset to network operation with a DHCP server. No network configuration settings

are required in this operating mode.

In case of manual allocation of IP addresses the device can be reached via the following IP

addresses (Factory setting):

For office networks:

IP Address

169.254.0.1

Subnet Mask

255.255.0.0

For automation networks:

IP Address

169.254.0.2

Subnet Mask

255.255.0.0

2TH LINK design

2.1 Connections and display elements

Chapter 2 - TH LINK design

Figure 1: TH LINK (front and lateral view)

[1] Ethernet interface for office network

olights yellow: Ethernet data communication

olights green: physical connection available

[2] LED ETH

olights red: boot procedure

olights green: firmware update in progress

ois off: boot procedure is completed

[3] LED RUN

olights red: internal error

olights green: power supply is applied

ois off: device is not powered

[4] LED BUS

olights red: relay contact active (error occurred in the bus)

olights green: TH SCOPE measurement is running

ois off: TH SCOPE measurement is stopped

[5] Ethernet interface for automation network

olights yellow: Ethernet data communication

olights green: physical connection available

[6] Terminal strip for +24 V DC power supply

oA: 24 V (+)

oB: 0 V (-)

oC: Relay contact - input

oD: Relay contact - output

oE: Protective earth

[7] SD card slot

[8] Type label

2.2 Mounting

[9] 35 mm DIN rail mounting unit (not included in the delivery)

TH LINK PROFINET - Installation Manual

2.3 SD card

TH LINK disposes of an SD card slot (refer to Connections and display elements [7]). You can save data

on the SD card to have the data available even after voltage recovery. You can find a list of

recommended SD cards in Release Notes on your installation CD or in the Softing download area

(http://industrial.softing.com/en/downloads.html).

1. Insert the SD card before installing the device or putting it into operation. Thus you make sure the

card is recognized during boot procedure.

2. Now go to TH LINK Settings TH SCOPE and set the parameter Data restore after voltage

recovery to Yes (see also TH SCOPE).

3. Following the initial device commissioning the SD card is formatted automatically. From this time

on you can save data independently from power interruptions.

Note

If the SD card is not recognized during boot procedure, restart the TH LINK.

Note

If the device power supply is interrupted, all previously saved data will be retained on the

SD card. Following a device restart the data will be read. In case the TH LINK detects a faulty

file system or no existing TH LINK structure during startup, the card will be formatted again.

The position of the blocking switch at the left card border has no effect, i.e. the card will

also be formatted or written in the blocked state.

3Start-up guideline

The following steps are required for start-up:

1. Mounting (see Mount/unmount device).

2. Plug-in SD card (recommended - see SD card).

3. Connect to network (see Connect to network).

4. Connect to the power supply (see Connecting the power supply).

5. Configure network (see Configure the device in the network).

Note

To set the IP address manually you must connect a PC to the device via crossover

cable.

4Mount/unmount device

4.1 Mount device

Note

Make sure you have a minimum of 5 cm below and above the TH LINK in order to ensure

heat dissipation.

Autres manuels pour TH LINK PROFINET

Table des matières

Manuels Équipement de diagnostic populaires d'autres marques

Mindray

Mindray M7Vet Guide de démarrage rapide

Autel

Autel MaxiProgrammer 201 Manuel utilisateur

TEXA

TEXA TMD2 Manuel utilisateur

Autel

Autel MaxiIM IM608 Manuel utilisateur

Sealey

Sealey BT2012 Manuel utilisateur

Diagnoptics

Diagnoptics Age Reader Manuel utilisateur

LAUNCH TECH

LAUNCH TECH X-431 PRO5 Manuel utilisateur

Hella Gutmann

Hella Gutmann Mega macs X Manuel utilisateur

Foxwell

Foxwell I80TS Manuel utilisateur

KaVo

KaVo 3D eXam Manuel utilisateur

ATEQ

ATEQ VT46 Manuel utilisateur

Hella Gutmann

Hella Gutmann mega macs X Manuel utilisateur

Autel

Autel MaxiFlash VCMI Manuel utilisateur

Qiagen

Qiagen QIAcube Connect MDx Manuel utilisateur

Alber

Alber BDSU Manuel utilisateur

St. Jude Medical

St. Jude Medical QUANTIEN Manuel utilisateur

Bosch

Bosch DCU 100 Manuel utilisateur

Launch

Launch CNC-602A Manuel utilisateur