4.3 Preparation beforeUse:
1.
Remove the outer packaging ofall products (including the protective foam in the packaging box)
2.
Inventory of accessories: Please check the accessories and materials according to the packing list.
3.
Cleaning: Clean the product once before use.
4.4 First Power-on
When using the equipment for the first time, please follow these steps:
1.
After the equipment is placed, leveled, and cleaned, it shall stand for more than 24 hours, and then power it on
to ensure the normal operation of the equipment.
2.
Under no-load condition, connect the power cord to a dedicated outlet with appropriate specifications.
3.
After plugging in, turn on the power switch of the equipment.
4.
Check whether the operating temperature of the equipment reaches the required value, observe the normal
start and stop of the equipment for 24 hours, and put a small amount of items in the freezer after confirming
the normal performance.
5.
Please store items in batches, with the items not exceeding 1/3 of the freezer volume each time.
6.
Try not to open the door during cooling, otherwise the temperature will rise.
4.5 Operation after PowerFailure
1.
The equipment has a memory function for the set value. When the power is restored after power failure, the equipment
will continue to operate before power failure.
2.
Once the equipment is powered off, it requires 5 minutes before it can be switched on again, so as to avoid
damaging the compressor.
3.
We guarantee the normal operation of this equipment under certain conditions, but we are not responsible for
any loss or damage of stored items after a power failure.
Notes:
◆
Aspecialpersonshallbe responsibleforcheckingandrecordingtherunningstatusoftheequipmenteveryday
(recordand checkonce every 2-4 hours).Incaseoffailureorshutdown,thetemperatureinthefreezer willrise.
Ifitcannot be repaired in a short time, please take out the stored items and transfer them to a place that
meets the temperature requirements for storage to avoid damage to the items.
◆
Before putting items into the equipment, it shall be confirmed in advance whether the temperature range of the
equipment meets the temperature requirement of the items, so as to avoid damage to stored items due to the
differencebetweenthe settabletemperatureoftheequipmentand therequiredtemperatureoftheitems.Please
payattentionnottoblock theair outlet and air inlet when putting items into the equipment.
◆
Dueto the refrigerationinertia, thereisa certaindifferencebetween theactualdisplaytemperature
andthe settemperature of the equipment, which is a normal phenomenon.
◆
The equipment is an item storage equipment, which cannot be used for routine production operations. It is
strictly forbiddentoputtoo manyitemswhicharerelativelyhotintotheequipmentatonetime,otherwisethe
compressorwillrun foralong time,andbe burneddueto high temperature.Itemsmust be putin batches,soas
toensurethat the freezer is cooled step by step until the temperature required for storing items isreached.
◆
Electrical appliances without production license shall not be usedinside the equipment.
◆
Donotchangethesettemperaturefrequentlyina shorttime,otherwisetheexpectedsettingeffectmaynotbe
achieved duetothelargetemperatureinertia;Ensurethatthereisacertainaircirculationspacearoundthe
cabinetwhenputtingin items, especially do not block the temperature sensor in the cabinet (for collecting
the temperature of the cabinet), otherwise itwill affectthe stability and accurate control ofthe temperature in
thefreezer body!
◆
Itemsshallnotbeplaced directlyatthebottom ofthefreezer,but onthebottomshelf, otherwisethe
refrigerationeffectofthe equipment will be affected.
◆
When putting in items, if the moisture content of the items is too much or too little, it will affect the humidity
change in thecabinet, so it is best to keep the items sealed; The humidity of the working environment will affect
thechangeofhumidity in the cabinet, especially if the door is opened too frequently and the door is not closed
properly
5
