-
2.2. Button Function
Button Armed Disarmed IGN On
BTN #1 once Arm Arm Door Lock
BTN #2 once Disarm Disarm Door Unlock
BTN #1 2 sec. Panic Panic
BTN #3 once Car Finder Car Finder
BTN #3 2 sec. Boot Release Boot Release Boot Release
BTN #4 3 sec. Remote Engine Start Remote Engine Start Anti-hijacking
BTN #2+3 once* Status Report Status Report Status Report
BTN #1+2 once Silent Disarm Silent Disarm Silent Disarm
BTN #1+3** CH3 CH3 CH3
BTN #1 then #1 once Arm & Bypass I
BTN #1 then #1 twice Arm & Bypass II
BTN #1+4 1 sec. Passive Arming On/Off Passive Arming On/Off
BTN #2+4 once* 2way RC Power Saving 2way RC Power Saving
BTN #3+4 once* 2way RC Vibration On/Off 2way RC Vibration On/Off 2way RC Vibration On/Off
*=For 2way LCD remotes only.
**=The CH3 output will be continuous whilst BTN #1+3 are pressed.
2.3. Programming New Remote Controls
The included remote controls have been programmed to the system in the factory. Follow the procedure below to program a
new remote control to the system:
- Turn the ignition on with the system disarmed.
- Within 10 seconds, press valet switch 6.
- The siren sounds for 2 sec. to confirm the system is now in code learning mode.
- Within 10 sec., press any button of 1st remote control
The siren will sound for 1 sec. and hazard lights flash twice to confirm the 1st remote has been programmed to the system
and all the previous codes in the system will be erased entirely.
- Within 10 sec., repeat for the 2nd remote control and again for 3rd and 4th remotes as applicable.
* Up to 4 remotes can be programmed to the system
* The system will leave the code learning mode after programming 4 remotes to the system and the siren will sound for 2
secondsto confirm.
* If no buttons are pressed within 10 seconds, the system will leave the learning code mode and the siren will sound for 2
seconds to confirm.
* The system will leave the code learning mode if the ignition is turned off at any time and the siren will sound for 2 seconds
to confirm.
2.4. To Arm the System
A. By remote control
Remote Arming:
- With the system disarmed and ignition off.
- Press button #1 once.
- Siren chirps once.
- Hazard lights flash once.
- Doors lock and windows close.*
- LED flashes slowly to confirm the system is armed.
* Window closure requires car with total closure or separate window closure module.
B. By passive arming
To turn the Passive Arming feature on or off:
- While the system is disarmed or the ignition is on:
- Press button #1+4 for 1 sec.
- The siren will chirp once to confirm the function is on.
- The siren will chirp twice to confirm the function is off.
When Passive Arming is on:
- Turn the ignition off and close the doors, bonnet and boot properly.
- LED indicator flashes rapidly.
- The system will automatically be armed 30sec. later.
- The siren chirps once and hazard lights flash once to confirm the system is armed.
* The doors will also lock when the system is armed if optional feature #2 is enabled.
* The 30 second countdown will be interrupted if any of the doors, boot or bonnet are opened. Closing the last opened
door, boot or bonnet will restart the 30 sec. countdown.
C. By auto rearming
If optional feature #11 is enabled the system will rearm itself to avoid accidental disarming as follows:
- Disarm alarm by remote control.
- The system will arm itself again 30 sec. later unless any of the doors, boot or bonnet are opened.
