Snapper SPX Series Manuel utilisateur

Revision B

Not for

Reproduction

Table of Contents:

General Information..............................................................3

European Office Contact Information.................................3

European Union (EU) Stage V (5): Carbon Dioxide (CO2)

Values.....................................................................................3

Operator Safety..................................................................... 3

Save these instructions.................................................... 3

Slope Identification Guide................................................ 3

Safety Symbols and Meanings.........................................4

Safety Alert Symbol and Signal Words............................ 4

Safety Decals................................................................... 5

Safety Messages.............................................................6

Features and Controls..........................................................6

Control Symbols and Meanings....................................... 6

Electronic Maintenance Display....................................... 7

Operation............................................................................... 8

Operating Area................................................................. 8

Safety Interlock System Tests..........................................9

Engine...............................................................................9

Tractor Operation........................................................... 12

Maintenance.........................................................................14

Maintenance Schedule...................................................14

Tire Pressure Check...................................................... 15

Battery Maintenance.......................................................15

Mower Blade Stop Time.................................................15

Change the Engine Oil...................................................15

Air Filter Assembly (Cartridge with pre-cleaner).............17

Push the Tractor By Hand............................................. 17

Check the Spark Plugs.................................................. 18

Towed Equipment...........................................................18

Clean the Mower Deck (if equipped)..............................18

Storage................................................................................. 19

Troubleshooting..................................................................20

Troubleshooting the Rider..............................................20

Troubleshooting the Mower............................................20

Specifications......................................................................21

Specifications Chart.......................................................21

Power Ratings Disclaimer.............................................. 21

Not for

Reproduction

General Information

For additional information, refer to theCustomer Contact

Guideincluded with the unit.

The illustrations in this document are representative.

Your unit might look different from the images

shown.LEFTandRIGHTare referenced from the operator's

position.

The use of Important and Note in the text shows clarifications,

exceptions, or alternatives to the procedures.

All language translations of this document derive from the

initial English source file.



Recycle all packaging, used oil, and batteries according to

applicable government regulations.

European Office Contact

Information

For questions regarding European emissions, please contact

our European office at:

Max-Born-Straße 2, 68519 Viernheim, Germany.

European Union (EU) Stage

V (5): Carbon Dioxide (CO2)

Values

Carbon dioxide values of Briggs & Stratton® EU Type-

Approval Certificate engines can be found by entering CO2

into the search window on BriggsandStratton.com.

Operator Safety

Save these instructions

Save these instructions for future reference.This manual

contains safety information to make you aware of the hazards

and risks associated with the product and how to avoid them.

It also contains important instructions that must be obeyed

during the initial set-up, operation, and maintenance of the

product.

This product is designed and intended for cutting well

maintained grass and is not intended for other purposes.

It is important that you read and understand these instructions

before you attempt to start or operate this equipment.

Make sure that you are fully familiar with the controls and the

correct use of the product.

Know how to stop the unit and disengage controls quickly.

Slope Identification Guide

How to measure the slope of a lawn surface with a

smartphone or an angle finder tool:

WARNING

Do not operate on slopes greater than10degrees.

1. Use a straight edge at least two (2) feet long (A,

Figure1). A 2x4 or a straight piece of metal works well.

2. Angle finder tools.

a. Use your smartphone:Many smartphones (B,

Figure1) have an inclinometer (angle finder) located

under the compass application (app). Or, search an

app store for an Inclinometer app.

b. Use angle finder tools:Angle finder tools (C and

D, Figure1) are available at local hardware stores

or online (also called inclinometer, protractor, angle

meter, or angle gauge). Dial type (C) or digital type

(D) work, others may not.Read and obey the user

instructions supplied with the angle finder tool.

3. Put the two (2) feet long straight edge along the steepest

part of the lawn slope. Put the board up and down the

slope.

4. Lay the smartphone or angle finder tool on the straight

edge and read the angle in degrees. This is the slope of

your lawn.

Note:A paper gauge slope identification guide is included

in your product literature packet and is also available to

download from the manufacturer's website.

Not for

Reproduction

Safety Symbols and Meanings

Symbol Meaning

Safety information about hazards that can result in personal

injury.

Read and understand the Operator's Manual before you

operate or service the unit.

Remove the key and read the Operator's Manual before

you service the unit.

Stop

Fire hazard

Explosion hazard

Shock hazard

Toxic fume hazard

Moving parts

Wear eye protection.

Hazardous chemical

Symbol Meaning

Hot surface hazard

Amputation hazard

Thrown objects hazard

Keep a safe distance

Keep children away

Amputation hazard

Roll-over hazard

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information

about hazards that can result in personal injury. A signal word

(DANGER,WARNING, orCAUTION) is used with the alert

symbol to indicate the likelihood and the potential severity of

injury. In addition, a hazard symbol may be used to represent

the type of hazard.

DANGERindicates a hazard which, if not

avoided,willresult in death or serious injury.

WARNINGindicates a hazard which, if not

avoided,couldresult in death or serious injury.

Not for

Reproduction

CAUTIONindicates a hazard which, if not

avoided,couldresult inminor or moderate injury.

NOTICEindicates information considered important but not

hazard-related.

Safety Decals

Before you operate the unit, read the safety decals.Compare

Figure2to the decals shown in the table that follows. The

cautions and warnings are for your safety. To avoid personal

injury or damage to the unit, understand and obey the safety

decals.

IMPORTANT:If the safety decals become worn or damaged,

and cannot be read, order replacement decals from your local

dealer.



Not for

Reproduction

Safety Messages

WARNING

Read, understand, and obey all the instructions and

warnings in the Operator's Manual and on the machine,

engine, and attachments before you operate this machine.

Failure to obey the safety instructions in this manual and on

the equipment could result in death or serious injury.

• Only let operators who are responsible, trained and

familiar with the instructions and physically capable to

operate the machine.

• Do not operate the machine while under the influence of

alcohol or drugs.

• Wear safety glasses and closed toe footwear.

• Do not put hands or feet near rotating parts or under

the machine. Keep clear of the discharge opening at all

times.

• Keep the machine in good working order. Replace worn

or damaged parts.

• Be careful when youservice the blades. Wrap the

blades or wear gloves. Replace damaged blades. Do

not repair or alterthe blades.

• Use full width ramps when you load and unload a

machine for transport.

• See attachment or accessory for proper wheel weights

or counterweights.

• To help prevent fires, keep machine free of grass,

leaves, or other unwanted material. Clean remaining oil

or fuel spillage. Remove fuel soaked debris and let the

machine to cool before storage.

WARNING

Running engine gives off carbon monoxide, an odorless,

colorless, poison gas. Breathing carbon monoxide can

cause headaches, fatigue, dizziness, vomiting, confusion,

seizures, nausea, fainting or death.

• Operate equipment ONLY outdoors.

• Keep exhaust gas from entering a confined area

through windows, doors, ventilation intakes, or other

openings.

Features and Controls

Make sure that the callout letters in Figure3agree with the

features and controls listed in the table that follows.

Control Symbols and Meanings

A Electronic Dash Panel

B Reverse Mowing Option (RMO)

Not for

Reproduction

CIgnition Switch

OFF

ON

START

DHeadlight Switch

EPower Take-Off (PTO)

FPower Take-Off(PTO), Engage

Blades

GPower Take-Off (PTO), Disengage

Blades

H Cruise Control

IParking Brake Control

JThrottle Control

KThrottle Control SLOW Position

LThrottle Control FAST Position

MChoke

NFuel Level Gauge (if equipped)

OGround Speed Pedals

PSeat Adjustment Lever

QMower Lift Lever

R Height-of-Cut Switch

STransmission Release Lever

TFuel Tank

UBrake Pedal

Electronic Maintenance Display

Not for

Reproduction

Note:When you start the unit, the Total Hours show on the

maintenance display. The total hours will set to 0 after 999.9.

Display Total Hours, Trip Hours, and Clock

1. Push MODE (A, Figure4) for less than 1 second to show

the Trip Hours.

2. Push RESET (B) for more than 3 seconds to set the Trip

Hours to 0.

3. Push MODE for less than 1 second to show the Clock.

SeeSet the Clocksection.

4. Push MODE for less than 1 second to show the Total

Hours.

Set the Clock

1. Push MODE (A, Figure4) for more than 3 seconds. The

hours will flash on the display.

2. Push RESET to adjust the hours.

3. Push MODE for less than 1 second to save the setting.

The minutes will flash on the display.

4. Push RESET to adjust the minutes.

5. Push MODE for less than 1 second to save the setting.

Maintenance Display

OIL CHANGE- This message shows after 50 hours of

operation. After you change the oil and filter, push MODE two

times to show OIL HRS. Then, push and hold MODE for 3

seconds to set the timer to zero.The display will automatically

clear.

AIR FILTER CHECK- This message shows after 25 hours of

operation. After you clean or change the air filter, push MODE

three times to show AIR FILTER HRS. Then, push and hold

MODE for 3 seconds to set the timer to zero.The display will

automatically clear.

CHANGE BLADES- This message shows after 100 hours

of operation. After you change the blade, hold the RESET

button for more than 3 seconds to set the timer to zero.The

display will automatically clear.

LOW BATTERY- This message shows when a battery

voltage problem occurs. The display will automatically clear

after servicing of the battery.



Note:The LOW BATTERY message shows on the display

before all other messages. Do the servicing ofthe battery

first. Then, do a check for other maintenance messages.

Operation

Read theOperator Safetysection before you operate this

machine. Make sure that you know the controls and how to

stop the unit.

Operating Area

1. Know the area where you plan to operate the mower.

2. Make sure that the area is free of unwanted material that

could be picked up by the blades and thrown.

DANGER

This machine is capable of throwing objects that could

injure bystanders or cause damage to buildings.

• Do not operate the machine without the entire grass

catcher, discharge chute, or other safety devices in

place and functioning properly. Check frequently for

signs of wear or deterioration and replace as needed.

• Clear the operating area of any objects which could

be thrown by or interfere with the operation of the

machine.

3. Move the rider mower outside, before you start the

engine.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

4. Note all slopes and drop-offs.

DANGER

Operating on slopes, or near water, or drop-offs can result

in loss of control and roll-over.

• Mow up and down slopes not across.

• Reduce speed and be careful on slopes.

• Do not operate on slopes over 10 degrees, which is a

3.5 foot rise over a 20 foot length.

• Give yourself a minimum of two mower widths of

clearance around water, retaining walls, or drop-offs.

• Avoid mowing wet grass.

• Do not operate machine under any condition where

traction, steering, or stability is in question. Tires could

slide even if the wheels are stopped.

• Avoid starting and stopping on slopes.

• Avoid making sudden changes in speed or direction.

• Make turns slowly and gradually.

• Be careful while operating machine with a grass catcher

or other attachment(s). They can affect the stability of

the machine.

• Follow the manufacturer's recommendation for weight

limits for towed equipment and towing on slopes.

SeeTowed Equipment.

5. Make sure that the operating area is clear of bystanders,

especially children.

Not for

Reproduction

DANGER

This rider mower is capable of amputating hands and feet.

• Stop the mower when children or others are near.

• Keep children out of the operating area and under the

watchful care of a responsible adult.

• Do not carry passengers, especially children, even

with the blade(s) shut off. Children can fall off and be

seriously injured or interfere with the safe machine

operation. Children who have been given rides in

the past can suddenly appear in the mowing area for

another ride and be run over or backed over by the

machine.

• Use care when approaching blind corners, shrubs,

trees, or other objects that obscure vision.

Safety Interlock System Tests

This machine is equipped with a Safety Interlock System.

Do not attempt to bypass or tamper with the switches

anddevices.

WARNING

If the machine does not pass a safety test, do not operate

the machine. See an Authorized Dealer.

Test 1 — Engine will NOT crank if:

• Power Take Off (PTO) switch is ON, OR

• Brake pedal is NOT fully pushed down (parking brake

OFF)

Test 2 — Engine will crank and start if:

• PTO switch is OFF, AND

• Brake pedal is fully pushed down (parking brake ON).

Test 3 — Engine will SHUT OFF if:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with brake pedal NOT fully pushed

down (parking brake OFF).

Test 4 — Mower Blade Stopping TimeCheck

The mower blades and mower drive belt willcome to a

complete stop in five seconds after the PTO switch is OFF.

If the mower drive belt does not stop in five seconds, see an

Authorized Service Dealer.

Test 5 — Reverse Mowing Option (RMO) Check

• The engine will STOP when reverse travel is attempted

with the PTO switched ON and the Reverse Mowing

Option (RMO) not activated.

• The RMO light will come on when the RMO has been

activated.

DANGER

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the

presence of children. DO NOT activate the Reverse Mowing

Option (RMO) if children are present. Children are often

attracted to the machine and the mowing activity.

Engine

Check and Add Engine Oil

Use Briggs & Stratton®Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable

if classified for service SF, SG, SH, SJ or higher. Do not use

special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard

starting.

B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 can cause increased

oil consumption. Check oil level more frequently.

C 5W-30

D Synthetic 5W-30

EVanguard®Synthetic 15W-50

*Below 40°F (4°C) the use of SAE 30 will result in hard starting.

**Above 80°F (27°C) the use of 10W-30 can cause increased oil consumption.

1. Put the unit on a level surface as shown in Figure5.

Not for

Reproduction

2. Stop the engine and remove the key. Make sure that the

oil fill area is clean.

3. Remove the dipstick (A, Figure6).Remove the remaining

oil from the dipstick.

4. Install and tighten the dipstick.

5. Remove the dipstick again, and check the oil level.

6. Make sure that the oil level is at the top of the FULL mark

(B) on the dipstick.

7. If the oil level is FULL, install and tighten the dipstick.

8. If the oil level is LOW, add oil into the oil fill tube (C). 

Note:DO NOT add oil at the quick oil drain (if equipped).

9. Wait one minute, and check the oil level again.

10. Install and tighten the dipstick.

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped)

will either stop the engine or activate a warning device on the

equipment. If this occurs, stop the engine and check the oil

level with the dipstick.

If the oil level is below the ADD mark, add oil until it touches

the FULL mark. Start the engine and check for the correct oil

pressure before you operate the machine.

If the oil level is between the ADD and FULL marks,DO NOT

start the engine. Contact an Authorized Service Dealer to

correct the oil pressure.

Fuel Recommendations

Fuel must meet these requirements:

Not for

Reproduction

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Snapper Tondeuse à gazon

Snapper

Snapper LT145H33HBV Manuel d'exploitation et d'entretien

Snapper

Snapper FRP2167517BV Manuel d'exploitation et d'entretien

Snapper

Snapper 375ZB2050CE Manuel utilisateur

Snapper

Snapper NZM21521KWV Manuel d'exploitation et d'entretien

Snapper

Snapper GT23540 Manuel utilisateur

Snapper

Snapper SV-18 Manuel utilisateur

Snapper

Snapper SCRAMBLER SZT18336BVE Manuel d'exploitation et d'entretien

Snapper

Snapper SERIES 16 250816B Manuel d'exploitation et d'entretien

Snapper

Snapper 7800190 Manuel utilisateur

Snapper

Snapper 7220 Manuel utilisateur

Snapper

Snapper E331315BVE Manuel utilisateur

Snapper

Snapper HZS15423KVE SERIES 3 Manuel d'exploitation et d'entretien

Snapper

Snapper HWPS26700BV Manuel d'exploitation et d'entretien

Snapper

Snapper ERZT20441BVE2 Manuel utilisateur

Snapper

Snapper C21500KWV Manuel d'exploitation et d'entretien

Snapper

Snapper R194014 Manuel d'exploitation et d'entretien

Snapper

Snapper Classic A21509B Manuel utilisateur

Snapper

Snapper Easy Line Series Manuel d'exploitation et d'entretien

Snapper

Snapper XD SXD19PWM82 Manuel utilisateur

Snapper

Snapper Powerake II PR3001 Manuel utilisateur

Snapper

Snapper 5900731 Manuel utilisateur

Snapper

Snapper EFRP216517BV Manuel d'exploitation et d'entretien

Snapper

Snapper SCRAMBLER SZT18426BVE Manuel d'exploitation et d'entretien

Snapper

Snapper ESPV21675 (7800253) Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur