Snapper 285Z Series Manuel utilisateur

285Z Series

Form No. 7104440

Rev. ‘-’, 6/10/2010

Briggs & Stratton Yard Power Products Group

Dealer Setup Instructions

Model. No. Description

7800632 Snapper 285Z Model RZT26520, 26HP w/ 52” Mower

7800578 Snapper 285Z Model RZT27460, 27HP w/ 46” Mower

Not for

Reproduction

285Z Series

Quick Setup List

Page Setup Procedure Steps to Perform

3Uncrating oRemove crate & banding.

oLocate literature pack and identify contents.

o Remove unit from bottom skid.

o Make sure roll release rods are in DRIVE position.

4Battery Activation &oCharge the battery

(Note: proceed with other setup steps

Installation

while battery is charging).

oInstall & secure battery.

5Mower Assembly o Torque the mower blade hardware.

6Check Fluid Levels oFill & check Engine oil level.

oReduce & check tire pressures

(Front tires 25 psi, rear tires 15 psi).

7Lubrication oLubricate all grease & oil points.

8Burnish PTO Clutch oBurnish PTO clutch

(run for 15 seconds, repeat 10 times)

8Final Adjustments oPerform any final adjustments as outlined in the

Operator’s Manual.

8SAFETY CHECKS oPerform SAFETY INTERLOCK SYSTEM CHECK.

o Perform MOWER BLADE STOPPING CHECK.

(Blade must stop within 5 seconds!)

WARNING

Grass Catcher bags used on this product are made of

woven fabric, and are subject to deterioration and wear

during normal usage. Check condition of bags before

each use. Immediately replace worn or damaged

catcher bags with only bags recommended by the

manufacturer. The Grass Catcher is optional equipment

on some models. WARNING

Battery posts, terminals and related accessories contain

lead and lead compounds, chemicals known to the State

of California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

WARNING

Engine exhaust, some of its constituents, and certain

vehicle components contain or emit chemicals known

to the State of California to cause cancer or other

reproductive harm.

Not for

Reproduction

Uncrating

1. Using a reciprocating utility saw or equivalent, cut

crate away from bottom skid. Remove crate. Remove

plastic wrap.

2. Cut any banding securing the unit.

3. Locate literature pack, and identify contents:

• Operator’s Manuals and associated literature

• Set of Keys (in ‘Kids and Mowers Don’t Mix’

Blister Pak)

• Washout Port Connector (Note: On some units,

this may be attached to the washout port,

located on the left side of the mower deck.)

4. Using a hoist or similar lifting method, lift the machine,

remove the bottom skid from under it, and lower the

machine onto the ground.

IMPORTANT: To avoid damage, be sure to lift the

machine by the frame.

5. Set the ground speed control levers to START/PARK,

and engage the parking brake.

6. Make sure that the roll release rods (Figure 1),

located on either side of the engine, are pushed

down into the DRIVE position.

NOTICE

When cutting crate from bottom skid, use caution

around tires and mower rollers.

NOTICE

Do not tow rider. Towing the unit will cause transmission

damage. Do not use another vehicle to push or pull this

unit. Do not use this unit to push or pull another vehicle

or object.

285Z Series

Figure 1. Roll release rods

Not for

Reproduction

WARNING

Corrosion hazard.

Batteries contain acid. Always keep the

battery upright and do not spill the

electrolyte. Avoid contact with skin and

eyes.

Explosion hazard.

Changing the battery produces explosive

hydrogen gas. Only charge the battery in a

well ventilated area, away from any ignition

source such as a water heater, electric

motor, or a lit cigarette.

Wear Protective Equipment

Always wear gloves and safety glasses

when handling the battery and battery

cables.

Battery Activation &

Installation

Charge Battery

1. Tip the seat forward to access the battery.

2. Remove the battery from the battery compartment,

and place the battery on a level, non-concrete sur-

face.

Note: When removing the battery cables from the bat-

tery, always remove the negative (-) cable first.

3. To charge the battery, follow the instructions provided

by the battery charger manufacturer as well as all

warnings included in the safety rules section of this

document. Charge the battery at 6-10 amps for 1

hour. Do not charge at a rate higher than 10 amps.

See Figure 2.

Figure 2. Charging the battery

Figure 4. Installing the battery cables

Install Battery

1. Install and secure the battery in the battery compart-

ment (Figure 3).

2. Connect the red positive battery cable (A, Figure 4) to

the positive battery terminal, then cover the positive

battery terminal with the terminal cover.

3. Connect the black negative battery cable (B) to the

negative battery terminal.

Figure 3. Installing the battery

285Z Series

Not for

Reproduction

285Z Series

Torque Mower

Blade Hardware

1. Check to see that the blade and hardware are

installed according to the diagram shown (A,

Figure 5).

2. Torque the blade hardware to the noted

torque (B):

Note: Use a wooden block to prevent blade

rotation.

50-60 ft. lbs.

68-81 N.m.

Figure 5. Torquing the mower blade hardware (46” & 52” decks)

Not for

Reproduction

Size PSI bar

Rear 15 1,03

Front 25 1,72

Check

Fluid Levels

Fill & Check Engine Oil

Raising the engine cover to gain access to the

engine (Figure 6, inset), use the dipstick to check

the engine oil level. If necessary add engine oil.

Check engine manufacturer’s owner’s manual for

oil recommendations.

Figure 6. Checking the fluid levels

Figure 7. Checking the tire pressure

Reduce & Check Tire

Pressures

The tires are over-inflated for shipping purposes. Inflate

to the pressures shown (Figure 7). Note that these pres-

sures may differ slightly from the “Max Inflation” stamped

on the side-wall of the tires. The pressures shown pro-

vide proper traction, improve cut quality, and extend tire

life.

285Z Series

Not for

Reproduction

285Z Series

Figure 8. Lubrication Points (Grease)

Lubrication

Lubricate the unit at the following lubrication points as

well as those shown in Figure 8.

Grease:

• front caster wheel axles

• front caster spindle bosses

• front axle center pivot

• mower blade spindles

• mower deck idler arm

• mower deck lift motor screw (located up under

right fender)

Oil:

• ground speed control lever pivot points

• discharge chute hinge

• deck lift pivot points

Generally, all moving metal parts should be oiled where

contact is made with other parts. Keep oil and grease off

belts and pulleys. Remember to wipe fittings and sur-

faces clean both before and after lubrication. Use grease

fittings when present. Disassemble parts to apply grease

to moving parts when grease fittings are not installed.

Not all greases are compatible. Use automotive-type

lithium grease.

* Some blade spindles have grease fittings above the

mower deck, while others have grease fittings below

the deck.

Not for

Reproduction

CHECK RIDER SAFETY

SYSTEM

This unit is equipped with safety interlock switches.

These safety systems are present for your safety. Do

not attempt to bypass safety switches, and never

tamper with safety devices. Check their operation

regularly.

Operational SAFETY Checks

TEST 1 — ENGINE SHOULD NOT CRANK IF:

• Mower blades switch is ON, OR

• Ground speed control levers are not in their

START/PARK positions, OR

• Parking brake lever is in DISENGAGE position.

TEST 2 — ENGINE SHOULD CRANK IF:

• Mower blade switch is OFF, AND

• Ground speed control levers are in their

START/PARK positions, AND

• Parking brake lever is in ENGAGE position.

TEST 3 — ENGINE SHOULD SHUT OFF IF:

• Operator rises off seat with the mower blade switch

ON, OR

• Operator rises off seat with the ground speed levers

in DRIVE positions, OR

• Operator rises off seat with the parking brake in

DISENGAGE position, OR

• Operator moves the left and/or right ground speed

control lever out of its START/PARK position with

the parking brake lever in ENGAGE position.

TEST 4 — BLADE BRAKE CHECK

The mower blades and mower drive belt should come

to a complete stop within five seconds after the mower

blade switch is turned OFF. If mower drive belt does

not stop within five seconds, contact your local autho-

rized dealer.

NOTE: Once the engine has stopped, the mower blade

switch must be turned OFF, the ground speed control

levers must be locked in their START/PARK positions,

and the parking brake lever must be in the ENGAGE

position in order to start the engine.

Burnish PTO Clutch

1. Follow fueling and starting procedures as outlined in

the Operator’s Manual.

2. Move the ground speed control levers into their

START/PARK positions, engage the parking brake,

and set engine speed to FAST.

3. Engage the PTO switch for fifteen seconds, then

disengage it and wait for the mower blades to stop.

4. Repeat Step 3 ten times, taking note of mower blade

stopping time. (Stopping time must be five seconds or

less.) If the unit fails this test, perform the PTO clutch

adjustment found in the “Regular Maintenance”

section of the Operator’s Manual, or replace the

clutch.

285Z Series

Final Adjustments

Perform any necessary adjustments to the unit as

outlined in the Operator’s Manual.

WARNING

If the unit does not pass a safety test, do not

operate it. See your local authorized dealer.

Under no circumstance should you attempt to

defeat the purpose of the safety interlock system.

Not for

Reproduction

Autres manuels pour 285Z Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Snapper Tondeuse à gazon

Snapper

Snapper ZF7302M Manuel utilisateur

Snapper

Snapper CRP216019KWV Manuel d'exploitation et d'entretien

Snapper

Snapper SVCB258 Manuel utilisateur

Snapper

Snapper 1650A Manuel utilisateur

Snapper

Snapper LT180H331BV series I Manuel d'exploitation et d'entretien

Snapper

Snapper LT23460AWS Manuel d'exploitation et d'entretien

Snapper

Snapper Finishing Mower Manuel utilisateur

Snapper

Snapper 7800832 Manuel utilisateur

Snapper

Snapper EASY LINE 21 Series Manuel

Snapper

Snapper V-Series Manuel utilisateur

Snapper

Snapper E251023BVE, E281223BVE, E28132 Manuel d'exploitation et d'entretien

Snapper

Snapper 5900769 Manuel utilisateur

Snapper

Snapper 421616BVE Manuel d'exploitation et d'entretien

Snapper

Snapper CAP21509R Manuel d'exploitation et d'entretien

Snapper

Snapper NR20500 Manuel utilisateur

Snapper

Snapper RP2167519BDV Manuel d'exploitation et d'entretien

Snapper

Snapper "MR" SERIES 17 EMRP216017B Manuel utilisateur

Snapper

Snapper FRP21600TV Manuel d'exploitation et d'entretien

Snapper

Snapper LT145H38CBV Manuel d'exploitation et d'entretien

Snapper

Snapper 250811BE Manuel d'exploitation et d'entretien

Snapper

Snapper NZM21521KWV Manuel d'exploitation et d'entretien

Snapper

Snapper LT145H38FBV Manuel d'exploitation et d'entretien

Snapper

Snapper WMRP216517B Manuel d'exploitation et d'entretien

Snapper

Snapper SGV13320KW Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur