Snap-On 5750 Manuel utilisateur

THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,

MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND

UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO

COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.

IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR SNAP-ON

PRODUCT, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE

DEPARTMENT AT 1-888-278-8092. BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION

AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE

REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE.

SNAP-ON®IS A TRADEMARK LICENSED BY SNAP-ON ®CORP.,

U.S.A., WHICH DOES NOT MANUFACTURE OR

DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE

DIRECTED TO:

1431 VIA PLATA

LONG BEACH, CA 90810-1462 USA

870534 – 5750/6800 WATT 13 HP Generator _Rev 10/14/09

FOR CUSTOMER SERVICE

1-888-278-8092

Printed in China

H EM

2222 A

A V02

C A V

H U

OSR

5750 / 6800W 13HP PORTABLE GENERATOR

INSTRUCTION MANUAL

TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-33

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

LIMITED WARRANTIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-40

CONGRATULATIONS!

You have purchased a heavy duty 5750 watt Generator featuring Snap On XT390

13 HP OHV 389CC engine for strong, steady performance. Additional features

include easy to use controls, heavy duty components and circuit protection.

Thanks for choosing this product. Our aim is to provide you with the highest quality

professional products, and we want you to be totally satisfied with your product and our

Customer Service. If any help or advice is needed, please contact us at 1-888-278-8092.

When properly cared for, this product will give you many years of satisfaction.

INTRODUCTION

This instruction manual is intended for your benefit. Please read and follow the safe-

ty, installation, maintenance and troubleshooting steps described within to ensure

your safety and satisfaction. The contents of this instruction manual are based upon

the latest product information available at the time of publication. The manufactur-

er reserves the right to make product changes at any time without notice.

GENERAL SAFETY

READ AND FOLLOW ALL INSTRUCTIONS.

Failure to follow all instructions in this manual may result in severe per-

sonal injury or death. Keep this manual and refer to it for Safety

Instructions, Operating Procedures, and Warranty.

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

The safety instructions provided in this manual are not intended to cover all possible condi-

tions and practices that may occur when operating, maintaining and cleaning power tools.

Always use common sense and pay particular attention to all the DANGER,

WARNING, CAUTION and NOTE statements in this manual.

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

TABLE OF CONTENTS

CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

GENERAL SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-4

IMPORTANT INFORMATION ABOUT THIS MANUAL . . . . . . . . . . . 4

UNPACKING & INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

SAFETY RULES FOR GASOLINE ENGINES . . . . . . . . . . . . . . . . . . . . . . 7-11

SYMPTOMS OF CARBON MONOXIDE POISONING . . . . . . . . . . . . 8

ADDING OR DRAINING FUEL TO OR FROM THE ENGINE . . . . . . . 8-9

STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10

MAKING ADJUSTMENTS OR REPAIRS TO THE ENGINE . . . . . . . . 10

TESTING SPARK PLUG FOR SPARK . . . . . . . . . . . . . . . . . . . . . . . 10

TRANSPORTING OR REPAIRING EQUIPMENT . . . . . . . . . . . . . . . . 11

STORING FUEL OR EQUIPMENT WITH FUEL IN FUEL TANK . . . . . 11

SAFETY RULES FOR GENERATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14

FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17

PREPARING THE PORTABLE GENERATOR . . . . . . . . . . . . . . . . . . . . . . 17-20

ADDING ENGINE OIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

LOW OIL SENSOR AND LED DISPLAY . . . . . . . . . . . . . . . . . . . . . . 17-18

ADDING FUEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

SYSTEM GROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

CONNECTING TO A BUILDING’S ELECTRICAL SYSTEM . . . . . . . . 19

HOUR METER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

OPERATING THE GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-27

STARTING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21

OUTLETS AND CIRCUIT PROTECTORS . . . . . . . . . . . . . . . . . . . . . 21-22

CONNECTING TO GENERATOR OUTLETS . . . . . . . . . . . . . . . . . . . 22-23

GENERATOR CAPACITY AND APPLIANCE WATTAGE . . . . . . . . . . . 24-26

STOPPING THE GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29

CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

CLEANING GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28-29

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29-30

GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

PREPARING FOR USE AFTER STORAGE . . . . . . . . . . . . . . . . . . . . 30

POISONOUS FUMES: This tool uses a gasoline powered engine that

produces poisonous fumes from its exhaust. Always make sure there is

adequate ventilation when operating this equipment.

EXPLOSION HAZARD: Fuel and its vapors are extremely flammable and

explosive. Fire or explosion from these vapors can cause severe burns or

even death.

ROTATING PARTS: Starter and other rotating parts on this tool can

entangle loose clothing, long hair and accessories resulting in moderate

to severe injury.

HOT SURFACES: Engine muffler and other engine parts can become very

hot. Coming in contact with hot engine components can cause serious

burns. Hot exhaust gases from the engine can cause clothing to ignite if

in contact for any length of time.

KICKBACK: Starter cord can kickback (recoil) very rapidly. Kickback will

recoil starter cord quicker than you can let go. This action can result in

broken bones, bruises, sprains or fractures.

UNIT IS HEAVY: Take care when lifting or moving unit.

IMPORTANT INFORMATION ABOUT THIS MANUAL

Improper and unsafe use of this generator can result in

death, fire and/or bodily injury. This instruction manual contains important

information about product safety. Keep the instruction manual available for

others to read before they use the generator.

Improper maintenance and operation are responsible for the majority of accidents

involving gas generators. The largest portion of these could be prevented by recog-

nizing the basic safety rules and precautions. Most accidents can be avoided if the

operator recognizes a potentially hazardous situation before it happens and by

observing appropriate safety rules and procedures as outlined in this manual.

Basic safety precautions are outlined in the SAFETY portion of this manual and

throughout the text in this manual where a potential hazard might occur.

Hazards that MUST be avoided to prevent serious injury follow headers marked DANGER

or WARNING. These same precautions are placed as labels on the tool itself.

NEVER use this generator for applications that are NOT specified in this manual.

DANGER indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

CAUTION used without the safety alert symbol

indicates a potentially hazardous situation which,

if not avoided, may result in property damage.

NOTE provides additional information that is useful

for proper use and maintenance of this tool. If a

NOTE is indicated, make sure it is fully under-

stood.

In addition to SAFETY ALERTS listed above, there could also be numerous symbols

alerting the operator that specific safety measures are required to safely operate this

tool. Learn these SAFETY SYMBOLS as well as the SAFETY ALERTS to prevent

injury to the operator and to bystanders.

READ OPERATING INSTRUCTIONS: Read and understand tool labels,

safety warnings and precautions in this manual before operating the tool.

Failure to follow WARNINGS could result in serious injury or even death

to the operator or bystanders.

FIRE HAZARD: Heat from engine exhaust can ignite combustible materi-

als, building structures or gas tanks resulting in a fire. Place the tool on

a flat surface a safe distance from buildings or other combustible

material. Ensure exhaust is directed away from tool.

ELECTRICAL SHOCK: This tool produces hazardous electrical voltage.

Read and become familiar with this manual’s WARNINGS and CAUTIONS

so that it is installed and used properly.

WEAR APPROVED EYE PROTECTION: This tool has rotating and moving

parts that could become airborne if damaged. Always wear approved eye

protection when operating equipment with moving parts. Safety glasses

must conform to the requirements of American National Standards

Institute (ANSI) Z87.1 and provide protection against flying particles

from both front and side.

3 4

Keep work area clean and well lit. Messy areas and cluttered workbenches

invite personal injury and/or property damage. Clear all work areas of unneces-

sary tools, debris, furniture, etc.

Make sure the work area is well ventilated. Never operate in an enclosed area.

Do not place objects on top or against the tool.

Handle correctly. Always operate according to the instructions provided.

Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

Keep children and visitors away. All children should be kept away from the

work area. DO NOT let children handle the tool. Maintain a safe distance for any

person near the work area.

Childproof the workshop. The use of master switches and padlocks is highly

recommended. Remove starter keys where applicable.

Stay alert, watch what you are doing, and use common sense. Do not stand

on tool. Do not use tool while tired or under the influence of drugs, alcohol

or medication. A moment of inattention while operating the tool may result in

serious personal injury.

Operating any tools or equipment under the influence of drugs, alcohol, or

medication can cause personal injury to yourself and others.

Use the right tool. Use tools properly and for their intended task. Do not force

a small tool to do the job of a heavy-duty tool. Using the right tool to do the

right job will make doing the job safer.

Always make sure the tool is in the OFF position when making adjustments,

changing parts, or performing any maintenance.

Service must be performed only by qualified repair personnel. Service or

maintenance by unqualified personnel may result in a risk of injury.

Do not use the tool if the power switch does not turn it “ON” or “OFF”. A tool that

cannot be controlled with the switch is dangerous and must be repaired.

Store all maintenance tools away from the immediate area before turning ON

the tool.

Do not overreach. Proper footing and balance is a must at all times while using

tools. Unstable support may lead to personal injury. Do not stand on the tool.

Serious injury could result if the tool tips over or you accidentally contact tool.

When using accessories, consult the owner’s manual provided by the manufactur-

er. The use of improper accessories may cause risk of injury to yourself and others.

UNPACKING & INSPECTION

After opening the carton, unpack your new generator and related parts & acces-

sories. Please inspect it carefully for any damage that may have occurred

during transit. If any parts are missing, please contact our Consumer Helpline:

Phone: 1-888-278-8092

Do not operate this generator if damaged during ship-

ment, handling or misuse. Damage may result in bursting, which can cause

serious injury or property damage. All damaged parts must be repaired or

replaced as needed prior to operating this generator.

Check to see that all nuts, bolts and fittings are secure before putting this genera-

tor into service. If you have any questions, or require assistance with damaged or

missing parts, please contact our Consumer Helpline: Phone: 1-888-278-8092

Please have the serial number, model number, date of purchase, and parts list (with

missing parts identified) available for reference when calling.

MODEL NUMBER:

SERIAL NUMBER:

DATE OF PURCHASE:

SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE

USING GAS GENERATOR.

GENERAL SAFETY RULE

People with electronic devices, such as pacemakers, should consult their physi-

cian(s) before using this product. Operation of electrical equipment or the elec-

tromagnetic wave created by the engine spark plug in close proximity to a heart

pacemaker could cause interference or failure of the pacemaker.

WARNING: This product contains chemicals known to the State of California to

cause cancer and birth defects or other reproductive harm.

WARNING: The Engine Exhaust from this product contains chemicals known to

the State of California to cause cancer, birth defects or other reproductive harm.

SYMPTOMS OF CARBON MONOXIDE POISONING

Carbon monoxide (CO) is a colorless, odorless, tasteless, extremely toxic gas that

can KILL in a matter of minutes. Breathing air containing carbon monoxide

produces symptoms of headache, dizziness, loss of muscular control, a sleepy

feeling and finally coma. Moderate or severe brain damage can result from inhaling

air containing carbon monoxide. Carbon monoxide is a product of incomplete

combustion of fuels and occurs in exhaust fumes of fuel-burning heaters and all

internal combustion engines. Carbon Monoxide collects in spaces where there is no

constant air flow or ventilation. If you start to feel sick, dizzy or weak due to

exposure to CO while using gasoline engine, GET TO FRESH AIR IMMEDIATELY.

ADDING OR DRAINING FUEL TO OR FROM THE ENGINE

Fuel and fuel vapors are extremely flammable and

explosive. Fire and explosion can result in severe burns

and even death.

• Turn engine to the OFF position and let cool at least two minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in fuel tank.

• DO NOT fill or drain fuel tank inside enclosed structures. Accidental sparks

can result in fires or explosions leading to severe burns and even death.

Keep protective guards in place and in proper working condition.

Maintain tools and equipment with care. They will function better and more

safely when kept clean and in good working condition. Keeping the tool clean,

dry, and free of grime will add to its life and performance.

Do not use the tool for applications other than specified.

SAFETY RULES FOR GASOLINE ENGINES

Carbon monoxide is a product of incomplete combustion, such as exhaust

from the engine. Carbon monoxide is colorless, odorless and tasteless and

can kill in a matter of minutes.

Gas particulate filters and respirators will not protect someone

from carbon monoxide poisoning. If symptoms of carbon monoxide

poisoning appear, take the affected person outdoors immediately

and away from all structures and equipment that could produce the

gas. Call for emergency medical treatment and make them aware of the sit-

uation.

Operate generator only outdoors. Do not allow exhaust gas fumes from

entering confined areas through windows, open doors, ventilation ducts and

other openings.

Do not start or run engine indoors or an enclosed area, such as a garage

(even if windows and doors are open). This also applies to the engine com-

partment of a recreational vehicle (RV).

The engine exhaust from this product contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive harm.

Install a battery powered Carbon Monoxide (CO) detector near all bedrooms to

alert occupants of dangerous levels of carbon monoxide. Carbon monoxide is a

colorless, odorless, very poisonous gas.

The Emission Control System for engine is warranted for standards set forth by the

EPA/Environmental Protection Agency and CARB/California Air Resources Board.

DO NOT tamper with Evaporation and Exhaust Assembly in the generator.

Do not contact muffler area with engine running. Muffler gets

extremely hot and can cause severe burns. Exhaust gases can

ignite combustible items such as clothing or structures in close

proximity. Gases leaking from worn muffler can heat up and

damage fuel tank resulting in fire or explosion.

• DO NOT touch hot parts of engine or muffler.

• AVOID hot exhaust gases.

• Keep a minimum of 5 ft. (1.5M) clearance on all sides of the engine including top.

Starter and other rotating parts of engine can entangle hair, hands,

clothing and accessories.

• NEVER operate with protective housing or covers removed.

• DO NOT use while wearing loose clothing or jewelry that may get caught up

in starter or other rotating parts. Tie up long hair or wear hair net or cap.

MAKING ADJUSTMENTS OR REPAIRS TO THE ENGINE

Excessively high operating speeds increase risk of injury and damage to

engine. Excessively low speeds produce heavy load on engine.

• DO NOT attempt to alter pre-set governed speed. Engine governor is factory

set to supply optimum output horse power (HP) when running at governed speed.

• DO NOT modify engine in any way.

TESTING SPARK PLUG FOR SPARK

• DO NOT check spark plug for spark by removing from head cylinder.

• Disconnect spark plug wire from spark plug and cover tip with

non-conducting material such as electrical tape to prevent it from coming in

contact with spark plug, fuel tank or other parts of the engine where damage

can result from sparking.

• Replace a defective spark plug only with authorized parts.

• Use approved spark plug tester.

• DO NOT overfill fuel tank. Leave ample space for expansion of fuel.

• DO NOT start engine in area of fuel spillage. Fire and explosion can occur.

• Keep fuel away from sparks, open flames, pilot lights, heat and other ignition

sources. DO NOT smoke while operating the engine.

• DO NOT tip engine or equipment at angle that could result in fuel spilling

from fuel tank.

STARTING THE ENGINE

Starter cord kickback (rapid retraction) can

pull your hand and arm toward the engine faster than it can be let

go of. Failure to be aware of this function can result in broken

bones, fractures, bruises and sprains can result.

• When starting the engine, pull cord slowly until resistance is felt, then pull

rapidly to avoid kickback.

Unintentional sparking can result in fire or electric shock.

Failure to observe this warning can result in property

damage, severe burns and/or death.

• Ensure spark plug is in place before attempting to start engine.

• Ensure muffler is secured to engine before starting.

• Ensure fuel cap is on fuel tank and tightened securely.

• Ensure air cleaner is clean and properly attached to engine.

A dirty air cleaner element changes the air to fuel ratio and

promotes incomplete combustion of fuel increasing the output of

carbon monoxide. Always make sure air cleaner element is clean

before every operation of the engine.

• DO NOT crank engine with spark plug wire removed. The resulting spark

could ignite spilled fuel.

910

TRANSPORTING OR REPAIRING EQUIPMENT

RISK OF PROPERTY DAMAGE WHEN TRANSPORTING GENERATOR

Turn off the generator before transport. Use caution when moving the genera-

tor. Oil can leak or spill and could result in fire or breathing hazard, serious injury or

death. Oil leaks will damage carpet, paint, or other surfaces in vehicles or trailers. Be

sure to use the handle to lift or carry the generator.

• The wheel kit is not designed for over-the-road use. generator

must be transported in a vehicle or on a trailer.

• Unit is heavy. Take care when lifting or moving unit.

• Transport or repair with fuel tank EMPTY to prevent an unintentional

spark igniting fuel vapors resulting in a fire or an explosion.

• Transport or repair with spark plug wire DISCONNECTED.

• Store away from furnaces, stoves, water heaters, clothes dryers, and all

other appliances with pilot lights or other ignition sources. These appliances

can heat fuel tanks and ignition sources can ignite fuel vapors.

STORING FUEL OR EQUIPMENT WITH FUEL IN FUEL TANK

Store away from furnaces, stoves, water heaters,

clothes dryers, and all other appliances with pilot lights or other ignition

sources. These appliances can heat fuel tanks and ignition sources can

ignite fuel vapors.

SAFETY RULES FOR GENERATORS

This generator does not meet U.S. Coast Guard Regula-

tion 33CFR-183 and should not be used on marine applications. USCG

Regulation 33CFR183 requires all electrical devices to be “ignition protect-

ed” when used in a gasoline-fueled (gaseous) environments such as engine

room or near fuel tanks. Failure to use appropriate U.S. Coast Guard

approved engine could result in death, serious injury or severe burns and

property damage.

Do not operate the generator in explosive areas, such as in the

presence of flammable liquids, gases or dust. Generators can cre-

ate sparks which may ignite the dust or fumes.

Never use the generator in damp or wet locations.

Wear proper apparel. Remove your jewelry before using generator. Do not

wear loose clothing, necklaces, rings, bracelets, or other jewelry, which may get

caught in moving parts. Nonskid footwear and electrically non-conductive

gloves are highly suggested while working. Wear protective hair covering to

contain long hair.

Be responsible for your hearing. Wear hearing protection during extended

periods of operation.

Do not use the generator if excessive noise or vibration is present. Have it

repaired immediately.

Never start or stop generator engine with electrical devices plugged in and/or

turned on. Damage to both electrical devices and generator can occur.

Never touch moving parts of the generator. This will cause the risk of injury.

Do not touch bare wires or outlets. Severe burns or even death can

result.

Do not use generator with electrical cords that are worn, frayed,

bare or otherwise damaged.

Store the generator indoors, in a dry, secured area away from other equip-

ment. Never store the generator near an open flame or flammable materials.

SPECIAL REQUIREMENTS

There may be Federal or State Occupational Safety and Health Administration

(OSHA) regulations, local codes or ordinances that apply to intended usage of gen-

erator. Consult a qualified electrician, electrical inspector or local agency responsi-

ble of usage of this type of equipment:

• In some areas, generators are required to be registered with local utility companies.

• If generator is used at a construction site, there may be additional regulations in place.

RISK OF FIRE OR EXPLOSION

Always store fuel away from the generator and in an

approved container.

Fuel and fuel vapors are extremely flammable and explosive.

Fire and explosion can result in severe burns and even

death.

Make sure all ventilation openings are clear and free from restrictions.

Restricted ventilation openings can cause overheating and/or fire.

RISK OF FALLING

Portable generators can fall from a table, workbench, or roof causing damage to

the generator and could result in serious injury or death to the operator. Always

operate generator in a stable and secure position to prevent accidental movement

of the unit. Never operate generator on a roof or other elevated position.

RISK OF PROPERTY DAMAGE WHEN TRANSPORTING GENERATOR

Turn off the generator before transport. Use caution when moving the genera-

tor. Oil can leak or spill and could result in fire or breathing hazard, serious injury or

death. Oil leaks will damage carpet, paint, or other surfaces in vehicles or trailers. Be

sure to use the handle to lift or carry the generator.

In order to avoid damaging the generator, do not allow the unit to be tilted more

than 10º from the normal horizontal position when operating.

The generator must be run with the rubber feet resting on a flat and stable hor-

izontal surface.

The generator must be used in a clean and well-ventilated area. The generator

requires an unobstructed airflow and must be located a minimum of 20 inches

from any walls or other obstructions that may prevent proper ventilation.

DO NOT place generator in an area:

• Where there is evidence of oil or gas leaks.

• Where flammable gas vapors or materials may be present.

• Where extremely dirty air or water could be drawn into the generator.

RISK OF EXPLOSION

Storage batteries give off explosive hydrogen gas during recharg-

ing. Hydrogen gas stays around the battery for a long time after the

battery has been charged. The slightest spark will ignite hydrogen

and cause an explosion. Blindness or serious injury could occur.

Battery electrolyte fluid contains acid and is extremely caustic. Contact with

battery fluid will cause severe chemical burns.

DO NOT allow an open flame, spark, heat or lit cigarette near the battery for

several minutes after charging battery.

Wear protective goggles, rubber apron and rubber gloves.

RISK OF INJURY

High voltage is used in the operation of this equipment. Death on

contact may result if safety precautions are not observed. Whenever

possible, keep one hand from touching equipment to reduce the

hazard of dangerous current flowing through vital organs of the body.

Do not be misled by the term low voltage. Voltages as low as 50 volts can cause death.

Generator produces hazardous voltages. Failure to isolate the generator from

the power utility can result in serious injury or death to electric utility workers

due to backfeed of electrical energy.

When using generator for backup power, notify utility company. Use approved

transfer equipment to isolate generator from electric utility.

Use a ground fault circuit interrupter (GFCI) in dampened or highly

conductive areas, such as metal decking or steel work.

RISK OF BURNS

Touching exposed metal such as the generator head or exhaust tube can

result in serious burns. Keep hands and fingers away from exposed

metal parts on generator during or immediately after operation.

Generators generate significant heat during normal operation and will

remain hot for some time after use. Do not reach around protective shrouds or

attempt any maintenance until generator has been allowed to cool. 14

ASSEMBLY

This generator requires some assembly and will be ready for use after servicing with

manufacturer approved oil and fuel. If you have any problems with the assembly of

your generator, please call the generator helpline at 1-888-278-8092. If calling for

assistance, please have the model, revision, and serial number from the data tag

available.

1. Unpack Generator. Set carton on a rigid, flat surface. Remove all loose parts

and packing. Leave generator in carton.

Unit is heavy. Do not attempt to lift and remove

the generator unit from the carton.

2. Using a box cutter, open carton completely by cutting the four corners allowing

the sides to lay flat.

3. Carefully lift the generator from the engine side and place upright and proceed

with assembling the wheels, legs and handle using the provided tool kit and

following the procedure in the assembly illustration. Make sure all hardware are

tightened properly.

4. After completion of the assembly, carefully

place the generator on its wheels and legs.

5. Lift the handle and move

the generator on a flat

surface to verify for proper

wheel and handle assembly.

FUNCTIONAL DESCRIPTION

GENERATOR FEATURES:

1. Handle Kit

2. Fuel Tank

3. Fuel Tank Cap

4. Fuel Gauge

5. CARB Fume Removal Tube

6. Choke Lever

7. Fuel Valve

8. Recoil Starter

9. Engine On/Off Switch

10. Low Oil Sensor LED

11.Hour Meter

12.Circuit Protectors

13.120V AC 20A, Duplex Outlet

MTE

22A22A

1CA V

HUO RS

HOURR

22A 2

A02

HURS

SR5750

14.120/240V AC, 30A, Locking Outlet

15. Grounding Terminal

16. Alternator Rear Cover

15. Rating Label

17. Oil Fill Cap

18. Rating Label

19. Leg Kit

20. Wheel Kit

21. Fuel Stabilizer

22. Engine Oil and Funnel

23. Tool Kit

Place on an even surface to correct this. If engine fails to start, the oil level may not be

sufficient to deactivate low oil level sensor. Add oil as described in previous section.

ADDING FUEL

1. Move the generator OUTSIDE and place on a flat and level surface.

2. Remove the gas tank cap. Carefully add 87 Octane (or higher) grade gasoline to

the tank. DO NOT OVERFILL. Leave room for the gasoline to expand.

3. Replace and hand tighten gas cap and wipe off any spilled fuel.

•DO NOT overfill fuel tank. Slowly add unleaded gasoline (A) to fuel tank (B). Use

extreme caution not to fill fuel above baffle (C). This allow appropriate space for

fuel expansion.

Fuel and fuel vapor are extremely flammable and

explosive. Fire or explosion from misuse of fuel can cause

severe burns and even death.

Failure to use fuel as recommended in this manual will void the warranty.

WHEN ADDING FUEL TO GENERATOR, OBSERVE THE FOLLOWING:

•DO NOT use unapproved gasoline such as E85 (85% ethanol/15% gasoline).

•DO NOT mix oil with gasoline.

•DO NOT modify engine to run on alternate fuels.

• Turn generator OFF and let it cool for at least two minutes before removing fuel

cap. Loosen fuel cap slowly to release pressure.

• Keep fuel away from sparks, open flames, pilot lights, heat and other ignition

sources.

•DO NOT light a cigarette or smoke near open fuel tank or container.

• Clean area around fuel fill cap and slowly remove cap to allow any pressure to

escape.

• Install fuel cap and allow any spilled fuel to evaporate before starting engine.

DO NOT over tighten handles on generator frame. Handles

must be allowed to move up and down with ease but not too loose as to rattle

during operation of the generator.

PREPARING THE GENERATOR

Improper treatment of generator can damage internal

components and shorten the life of unit.

ADDING ENGINE OIL

1. Move the generator OUTSIDE and place on a flat and level surface.

2. Remove the engine oil dip stick and place funnel in the oil reservoir.

3. Pour the supplied engine oil (30 weight)) until oil level reaches

the threads inside the oil reservoir.

4. Hand tighten oil dip stick and wipe off any spilled oil.

Improper treatment of generator can damage it and shorten its life.

DO NOT attempt to start generator engine before proper servicing using

recommended engine oil. Failure to observe this precaution can result in

engine failure.

LOW OIL SENSOR AND LED DISPLAY

To prevent engine damage caused by an insufficient amount of oil in

the crankcase, this generator is equipped with low oil sensor. If the

oil is below the safe amount, the sensor will activate and will prevent

engine start-up or will stop the running engine.

If the engine oil level is below a safe level and you attempt

to start the engine, the LED display on the front panel of the generator will blink.

Add oil as described in previous section.

If generator shuts off and the oil level is within specifications, check to see if

generator is sitting at an angle that forces oil to shift.

FILL LINE

Table des matières

Autres manuels Snap-On Générateur portable

Snap-On

Snap-On SR3000 Manuel utilisateur

Manuels Générateur portable populaires d'autres marques

Kohler

Kohler 20EORZ Mode d’emploi

Powerhorse

Powerhorse 83171 Manuel utilisateur

HURST

HURST ML-630-SI Manuel utilisateur

ETQ

ETQ TG4000 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton 40265 Guide de configuration

ConMed

ConMed 7550 Manuel utilisateur

Owon

Owon Waveform Generator Manuel utilisateur

evertz

evertz 7700 Series Manuel utilisateur

Power Stroke

Power Stroke PS906025 Manuel utilisateur

Firefly

Firefly Cygnus CYG2400/460/24 Manuel utilisateur

Draper

Draper PG950S Mise à jour du firmware

PowerBoss

PowerBoss PowerBoss Manuel utilisateur

SDMO

SDMO SH 4000 Manuel utilisateur

EINHELL

EINHELL STE 5500 Manuel utilisateur

Wanco

Wanco WI3000P Manuel utilisateur

Full Boar

Full Boar FBT-3300 Manuel utilisateur

Dwyer Instruments

Dwyer Instruments ASG Manuel utilisateur

Westinghouse

Westinghouse WH1000i Series Manuel utilisateur