Smooth Fitness CE-8.0LC Manuel utilisateur

OWNER’S

MANUAL

USER WEIGHT LIMITATION: 400lbs(181kgs)

SERIAL NUMBER (found on frame):_____________________

VERSION: IHP- I

CE-8.0LC

SAFETY INSTRUCTIONS

WARNING: Toreduce the risk ofserious injury, read the following Safety Instructions before using the

Elliptical Trainer.

1. Read all warnings posted on the Elliptical Trainer.

2. Read this Owner's Manual and follow it carefully before using the Elliptical Trainer. Make surethat it is properly

assembled and tightened before use.

3. We recommendthat twopeople be available for assembly of this product.

4. Keep children away from the Elliptical Trainer. Do not allow children to use or play on the Elliptical Trainer.Keep

children and pets away from the Elliptical Trainerwhen it is in use.

5. It is recommended that you place this exercise equipment on an equipment mat.

6. Set up and operate the Elliptical Trainer on a solid level surface. Donot position the Elliptical Traineron loose rugs or

uneven surfaces.

7. Inspect the Elliptical Trainerfor worn or loose components prior to use.

8. Tighten/replace any loose or worn components prior to using the Elliptical Trainer.

9. Consult a physician prior to commencing an exercise program. If, at any time during exercise, you feel faint, dizzy, or

experience pain, stop and consult your physician.

10. Follow your physician's recommendations in developing your own personal fitness program.

11. Always choose the workout which best fits your physical strength and flexibility level. Know your limits and train within

them. Always usecommon sense when exercising.

12. Before using this product, please consult your personal physician for a complete physical examination.

13. Do not wear loose or dangling clothing while using the Elliptical Trainer.

14. Never exercise in bare feet or socks; always wear correct footwear, suchas running, walking, or cross-training shoes.

15. Be careful to maintain your balance while using, mounting, dismounting, or assembling the Elliptical Trainer,loss of

balance may result in a fall and serious bodily injury.

16. Keep both feet firmly and securely on the Foot Pedals while exercising.

17. The Elliptical Trainershould not be used by persons weighing over 400 pounds /181 kgs.

18. The Elliptical Trainershould be used by only one person at atime.

19. Use two people to assemble and move the Elliptical Trainer.

20. Maintenance: Replace the defective components immediately and/or keep the equipment out of useuntil repair the

equipment completely.

21. Make sure that adequate space is available for accessto and passage around the Elliptical Trainer;keep at least a

distance of 1 meter from any obstruction object while using the machine.

WARNING: Before starting any exercise or conditioning program you should consult with your personal physician to seeif

you requirea complete physical exam. This is especially important if you are over the age of 35, have never exercised before,

are pregnant, or suffer from any illness.

READ AND FOLLOW THESAFETY PRECAUTIONS. FAILURE TO FOLLOW THESE

INSTRUCTIONS CAN RESULTIN SERIOUS BODILY INJURY

HARDWEAR IDENTIFICATION CHART

This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of the bolts,

or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.

NOTE: The length of all bolts and screws except those with flat heads is measured

from below the head to the end of the bolt or screw. Flat head bolts and

screws are measured from the top of the head to the end of the bolt or screw.

After unpacking the unit, open the hardware bag and make sure that you have all the following items. Some hardware

may be already attached to the part.

Part No. and Description Q’TY

66 Lock Washer (M8) 4

70 Washer (8x38x2.0t) 4

80 Screw, Round Head (M5xp0.8x15mm) 18

81 Screw, Round Head (M5xp0.8x50mm) 2

83 Bolt, Socket Head (M8xp1.25x10mm) 8

90 Bolt, Button Head (M10xp1.5x85mm) 2

94 Bolt, Hex Head (M8xp1.25x65mm) 4

95 Bolt, Hex Head (M10xp1.5x50mm) 2

104 Nylon lock Nut (M10xp1.5) 2

105 Nut Cap 2

“BEFORE YOU BEGIN”

Thank you for choosing the CE-8.0LC Elliptical.We take

great pride in producing this quality product and hope it will

provide many hours of quality exercise to make you feel

better, look better and enjoy life to its fullest.

Yes, it's a proven fact that a regular exercise program can

improve your physical and mental health.

Too often, our busy lifestyles limit our time and

opportunity to exercise. The equipment provides a

convenient and simple method to begin your assault on

getting your body in shape and achieving a happier and

healthier lifestyle.

Before reading further, please review the drawing below

and familiarize yourself with the parts that are labeled.

Read this manual carefully before using the equipment.

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY:

MULTI WRENCH TOOL

W/ PHILLIPS

SCREWDRIVER

ALLEN WRENCH

(6 mm)

PHILLIPS

SCREWDRIVER (6mm)

SOCKET WRENCH

(13mm)

T-HANDLE SOCKET

WRENCH (17MM)

Console

Handlebar

Accessory Tray

Main Frame

Front Stabilizer

Leveler

Pedal

Rear Stabilizer

Foam Grip

Upright Post

Pulse Sensor

Plate

“ASSEMBLYINSTRUCTIONS”

Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials

from your area and place them back into the box. Read each step carefully before beginning.

STEP 1–

LevelerAssembly

a. Attach the Levelerx 4(58) to the Front Stabilizer (2) and the Rear

Stabilizer (3).

b. Be sure to tighten the Leveler (58) securely against the Stabilizers(2, 3)

until screw completely tightened as the drawing 1 shown on the top right

corner.

STEP 2– Stabilizer Assembly

Attach the Front Stabilizer (2) and the RearStabilizer(3) onto the Main

Frame (1) and secure with the 4 x Washers (8x38x2.0t) (70), the 4 x Lock

Washers (M8)(66) and the 4 x Hex HeadBolts (M8xp1.25x65mm) (94) with

the socket wrench(13mm) (See picture above)

STEP 3– LevelerAssembly

Tighten one Leveler (58) under the middle of the MainFrame (1).

NOTE: It will be easier to attach the Leveler (58) under the MainFrame (1) by

placing one Styrofoam (or any stationary object) under one side of the Main

Frame (1).

Detailed Lever- drawing 1

Detailed Lever- drawing 2

LEVELING: After placing the

equipment in the intended

location for use, Check the

stabilityof the equipment. If the

equipment is not level,

reviewing the following

direction:

Loosen the Leveler(58) to

make theAdjustment Plate

become lesstight.

Adjust the Leveler (58) for

leveling.

Tighten the Adjustment Plate

securelyagainst the Stabilizer

to lock the Leveler (58) in the

stable position as the drawing

2 shown.

Stabilizer

Adjustment Plate

Leveler(58)

Adjustment Plate

Stabilizer

Leveler(58)

Screwline

“ASSEMBLYINSTRUCTIONS”

STEP 4 –Upright Sleeve Assembly

CAUTION: Be careful not to damage the Middle Connection Wire (109) while assembling Step 4 to 6.

Slide the Upright Sleeve (22) onto the Upright Post (4).

Refer to the drawing above. Make sure the direction of the Upright Sleeve (22) is in the correct position.

STEP 5 – Upright Post Assembly

a. Check that 2 x Nylon lock Nuts (M10x8t) (103) have preassembled into the front of the MainFrame (1) as FIG1

illustration shows on the top right corner, making sure that the slotted bracket of the upright post slides between the

nuts and the frame.

b. Insert the Upright Post (4) onto the MainFrame (1) and slightly secure with the 2 x Hex Head

Bolts (M10xp1.5x50mm) (95) by using the T-Handle SOCKET WRENCH(17mm) as shown.

NOTE: Please do not fully tighten Bolts (95) or lock nuts (103) until Step. 7 has

been COMPLETED

STEP 6 – Wire Assembly

Plug the Middle Connection Wire (109) into the Lower Connection Wire (110).

NOTE: Please do not fully

tighten Bolts (95) until Step. 8

for the easy assembly

NOTE: Do not remove the lock

nuts (103) during assembly

“ASSEMBLYINSTRUCTIONS”

STEP 7 – Pedal Support Arm

& Pivoting Arm Assembly

a. Attach the Left Pedal Support Arm

(10) onto the Left Pivoting Arm (8)

and secure with the 1x Button Head

Bolt (M10xp1.5x85mm) (90) and 1 x

Nylon lock Nut (M10xp1.5) (104).

b. Press the Nut Cap (105) onto the

Nylon lock Nut (M10xp1.5) (104).

c. Repeat the above procedure to attach

the Right Pedal Support Arm (11)

onto the Right Pivoting Arm (9).

Note: make sure the bolts are fully tightened to avoid noise

STEP 8 – Front Decoration Cover Assembly

a. Please go back to fully tighten with the 2 x

Hex Head Bolts

(M10xp1.5x50mm)

(95) and the 2 x

Lock nuts (103)

with the T-Handle

SOCKET WRENCH

(17mm) as shown.

b. Attach the Front Decorative Upright

Cover (21) onto the front of the Main

Frame (1) with the 2 x Round Head

Screws (M5xp0.8x50mm) (81).

c. Place the Logo Sticker on the surface of the

Front Decorative Upright Cover (21).

A logo sticker is located in one of the

hardware boxes.

d. Slide the Upright Sleeve (22) down to cover the open area of the MainFrame (1).

NOTE: Please make sure Bolts (90) are

inserted from the inside of the Pivoting Arm

and the Nuts (104) and Nut Caps (105) are

installed from the outside

“ASSEMBLY INSTRUCTIONS”

STEP 9 – Pedal Assembly

a. Attach the Left Pedal Assembly (33L)

onto the pedal arm plate that is

located in the middle of the Left Pedal

Support Arm (10) and secure with the

4x Socket Head Bolt

(M8xp1.25x10mm) (83).

b. Repeat the above procedure to attach

the Right Pedal Assembly (33R) onto

the Right Pedal Support Arm (11).

“ASSEMBLYINSTRUCTIONS”

STEP 10 – Console Bracket

Assembly

CAUTION: Be careful not to

damage the Middle Pulse Sensor Wire

(112) while assembling STEP 9.

Slide the Console Bracket (18) onto the

Upright Post (4) as the FIG1 illustration

shows on the top right corner.

STEP 11– Console Fixed Bracket Assembly

NOTE: For shipping purpose, the4 x Button Head Bolts (M8xp1.25x12mm) (87) and 4 x Lock Washers (M8)(66) are

attached on the Upright Post (4).

a. Remove the 4 x Button Head Bolts (M8xp1.25x12mm)(87) and 4 x Lock Washers (M8)(66) from the Upright Post

(4).

b. Attach the Console Fixed Bracket (43) onto the Upright Post (4) and secure with the 4 x Button Head Bolts

(M8xp1.25x12mm)(87) and 4 x Lock Washers (M8)(66)

STEP 12 – StationaryHandlebar & Wire Assembly

NOTE: For shipping purpose, the Button Head Bolts (M8xp1.25x16mm)(88) and Lock Washers (M8)(66) are attached

on the Stationary Handlebar (5).

a. Remove the 4 x Button Head Bolts (M8xp1.25x16mm)(88) and 4 x Lock Washers (M8)(66) from the Stationary

Handlebar (5).

b. Connect the Middle Pulse Sensor Wire (112) and the Lower Pulse Sensor Wire (113) to the Stationary

Handlebar (5).

c. Insert the Stationary Handlebar (5) into the Upright Post (4) and secure with the 4 x Button

HeadBolts (M8xp1.25x16mm)(88) and 4 x Lock Washers (M8)(66).

NOTE: After connecting the wires’ pins, slightly and gently pull two sides of wires to test and

make sure whether the wires are fully connected.

“ASSEMBLYINSTRUCTIONS”

STEP 13 –Wire Assembly

a. Connect the Upper Pulse Sensor Wire (111) to the Middle Pulse Sensor Wire (112).

b. Connect the Upper Connection Wire (108) to the Middle Connection Wire (109).

NOTE: The number of wire pin should be the same for both wires to connect with as the drawing

shown on the right.

STEP 14 –Console & Console Bracket Assembly

a. Place the Console (17) onto the Upright Post (4) and secure with the Round Head Screws (M5xp0.8x15mm) (80).

b. Attach the Console Back Cover (19) to the Console (17) under the Stationary Handlebar (5) and secure with the

Round Head Screws (M5xp0.8x15mm) (80).

c. Slide the Console Bracket (18) onto the Console (17) and secure with the Round Head Screws (M5xp0.8x15mm)

(80).

STEP 15 –Accessory Tray Assembly

NOTE: For shipping purpose, the Round Head Screws (M5xp0.8x15mm) (80) are attached on

the Upright Post (4).

a. Remove the Round Head Screw (M8xp1.25x15mm) (80) from the Upright Post (4).

b. Attach the Accessory Tray (23) onto the Upright Post (4) and secure with the Round

HeadScrew (M5xp0.8x15mm) (80).

Autres manuels pour CE-8.0LC

Table des matières

Autres manuels Smooth Fitness vélo elliptique

Smooth Fitness

Smooth Fitness CE 2.1E Manuel utilisateur

Smooth Fitness

Smooth Fitness CE-2.5 Elliptical Manuel utilisateur

Smooth Fitness

Smooth Fitness CE-3.6 ELLIPTICAL Manuel utilisateur

Smooth Fitness

Smooth Fitness CE 07859-999 Manuel utilisateur

Smooth Fitness

Smooth Fitness Smooth Agile Trainer Manuel utilisateur

Smooth Fitness

Smooth Fitness EVO REV 400 Manuel utilisateur

Smooth Fitness

Smooth Fitness AGILE Manuel utilisateur

Smooth Fitness

Smooth Fitness CE-3.0 XT Manuel utilisateur

Smooth Fitness

Smooth Fitness CE 3.2 Manuel utilisateur

Smooth Fitness

Smooth Fitness AGILE DMT X2 Manuel utilisateur

Smooth Fitness

Smooth Fitness Smooth 9.25X Manuel utilisateur

Smooth Fitness

Smooth Fitness CE-8.0LC Manuel utilisateur

Smooth Fitness

Smooth Fitness CE Instructions d'installation et d'utilisation

Smooth Fitness

Smooth Fitness CE 7.4 Manuel utilisateur

Smooth Fitness

Smooth Fitness CE-3.6 ELLIPTICAL Manuel utilisateur

Smooth Fitness

Smooth Fitness E7000P Manuel d'utilisation

Smooth Fitness

Smooth Fitness CE 7.4E Manuel utilisateur

Smooth Fitness

Smooth Fitness SMOOTH CE-9.0 ELLIPTICAL Manuel utilisateur

Smooth Fitness

Smooth Fitness CE-3.0 Manuel utilisateur

Smooth Fitness

Smooth Fitness SMOOTH CE2.7 Manuel utilisateur

Smooth Fitness

Smooth Fitness V2300 Manuel utilisateur

Smooth Fitness

Smooth Fitness CE 2.1 Manuel utilisateur

Smooth Fitness

Smooth Fitness CE-3.0DS Manuel utilisateur

Smooth Fitness

Smooth Fitness AGILE DMT X2 Manuel utilisateur

Manuels vélo elliptique populaires d'autres marques

Weslo

Weslo Momentum 4.0 Elliptical Manuel d'utilisation et d'entretien

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manuel utilisateur

Torque Fitness

Torque Fitness XPLLP Manuel utilisateur

Octane Fitness

Octane Fitness PRO3700C Manuel utilisateur

Xterra

Xterra FS5.8e Manuel utilisateur

Bodyguard

Bodyguard E-40 Manuel utilisateur

Bonn Germany

Bonn Germany Concept 2.2 Manuel utilisateur

Precor

Precor Resolute RSL 620 Manuel utilisateur

NordicTrack

NordicTrack E 9.2 Elliptical Manuel utilisateur

Vision Fitness

Vision Fitness X6600iNetTV Manuel utilisateur

Matrix

Matrix MX-A5x Manuel utilisateur

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manuel utilisateur

Sears

Sears FREE SPIRIT C249 30737 0 Manuel utilisateur

True

True FS-64 Manuel utilisateur

Sport-thieme

Sport-thieme ST 310 Manuel utilisateur

VIRTUFIT

VIRTUFIT CTR 1.1 Manuel utilisateur

Kettler

Kettler GIRO C 1 Manuel utilisateur

CIRCLE FITNESS

CIRCLE FITNESS E7 Manuel utilisateur