SMONET 2PCS Manuel utilisateur
Wireless
Network Video Recorder System
User Manual
2PCS/4PCS/6PCS/8PCS
720P/960P/1080P
2CH/4CH/6CH/8CH NVR Kits
V.9-201905
01
Content
Package Contents
Camera System Installation
Password Management and Internet Connection
Remote Viewing on a Smart Phone
Viewing on PC by Eseecloud Software
Record Video
Playback Video
Frequently Asked Questions
02
03
05
08
09
11
14
15
02
Package Contents
USA Toll Free: (866) 678-0666 (Available after 5:00 PM at Pacific Time)
CANADA Toll Free: (888) 792-5254 (Available after 5:00 PM at Pacific Time)
UK Toll Free: 08004 725222
Skype ID for US&CA: safeskysales003
Skype ID for UK: SMONETSERVICE
Wechat for US&CA: B997520270
Website: WWW.SMONETCCTV.COM
Thank you for choosing Smonet product.
Here is the list for product and relevant accessories.
S/N
1
2
3
4
5
6
7
Item
NVR
IP Camera(2CH/4CH/6CH/8CH)
DC 12V/2A power supply(for NVR)-3.3 feet
DC 12V/1A power supply(for IPC2CH/4CH/6CH/8CH)-10 feet
3.3 Ft network cable
USB mouse
User manual
Quantity
1pc
2/4/6/8 pcs
1pc
2/4/6/8 pcs
1pc
1pc
1pc
How can I get product and technical support?
Preparation for setup
Before installation, be sure to have the following:
TV/PC monitor (Not laptop or all in one computer), with 1080P or higher resolution.
VGA or HDMI cables for connection to the TV/PC monitor.
Router (WAN) and Internet Service (for remote viewing)
Ethernet cable for connecting the NVR to the Router
If you purchased the system without a hard drive, you will need a hard drive if you
wish to record videos from the cameras.
Installing a Hard Drive (Skip this section if a hard drive was pre-installed)
Hard Drive Specifications: 4TB maximum, internal, SATA Interface, 3.5/2.5 inches
Please power off the NVR before installing the hard drive.
NOTE: A newly installed Hard Drive needs to be formatted before
recording. More information can be found at FAQ Part below.
1 Camera System Installation
Remove the cover from the unit,
and remove the top two screws
Remove the cover
Insert the hard drive, secure it
to the bottom of the unit with the
four screws
Connect the data wire and
power wire as shown
Replace the cover and fasten screws
03
Installing the system
Connect NVR and cameras with corresponding power adapters.NOTICE,
NVR Power Adapter: 12V/ 2A
Camera Power Adapter: 12V/ 1A
DO NOT USE WRONG ADAPTER FOR SYSTEM WORKING
Connect provided mouse to NVR box.
Attach provided antennas to cameras.
NOTE:
If antenna already has been screwed into the camera, please DO NOT unscrew it.
Otherwise camera will be broken. Systems have two different antennas. One can be
removed and the other cannot be, which is all-in-one.)
NOTICE,
Fasten antennas tightly for better signal transfer.
Connect NVR to PC Monitor or TV by VGA/ HDMI cable, please kindly noted that the
system doesn’t support on laptop and All- in-One PC for initial Setup.
Connect NVR to the router by provided Ethernet cable, the router must be
WAN(wide area work).
The NVR and cameras that came with your order have been paired and tested at
the factory to operate immediately when powered up. Pairing would only be neces-
sary if you add additional cameras to your system. (More on the pairing process
later)
04
VGA Port
(PC Monitor)
HDMI Port
(TV Monitor)
Ethernet Port
(Router)
USB Port
(Mouse)
Power Supply
Best placement of cameras in their final location
The NVR’s signal coverage is circular with the NVR’s antennas in the center. Signal
is strongest around the combined NVR antennas and weak in the area immediately
between the 2 antennas. For best signal reception the cameras should be placed
around the NVR and as close to the same horizontal plane as the location of the
NVR. The camera antennas should be vertical or perpendicular to the orientation of
the antennas on the NVR.
Password Management and Internet Connection
2
Log in: Right click your mouse to open the main menu on the home screen. Click
System Setup and the password page will appear.
NOTE: The Default Username is “admin” and a Password is not required. Leave
the password field blank. Simply click Login to access the System Setup menu.
Setting a Password: Right click on the home screen of your monitor, navigate to
System setup > System admin, click User on the left menu bar > Set password(Re-
quest: 8 Characters Max.. Keep it short.). Create a password and type it in the field,
repeat new password, click ‘OK’. Be sure to remember your password.
05
Best wireless signal Worst wireless signal
Check Network Status: With the NVR connected to your router via an Ethernet
cable, navigate to System setup > Network setup, make sure DHCP is checked. At
the bottom of the window you should see Network Status as Healthy Network.
Click Show QR Code, you should see Cloud ID.
06
Click network icon at the bottom right side of main screen > you should see page
of Fast network.
Once Cloud(P2P) is “Online”, you will be able to access videos from the cameras
remotely by PC or Smart Phone (More on this in the next Section of this manual).
If the system does not come “Online” please do the following:
1.Make sure the light at the network port of the NVR is flashing which indicates
active communication with the router. Re-seat or replace the cable if necessary.
07
From your Smartphone, download free App ‘IP PRO’ or ‘Eseecloud’ from Google
Play or App Store.
Click Register to create an account and password based on your email or phone
number. Be sure to remember your account login info.#Pic 1
Click "+", then click Add device by ID.#Pic2
On your device, either scan the QR code or manually enter your Cloud ID. You
can locate your Cloud ID on your monitor screen as seen earlier in section 2 of
this manual. (Use NVR login Username/password on your monitor screen
here).#Pic3
If you have multiple Smartphones, you must register multiple accounts. You
cannot have one account across multiple devices.
Remote Viewing on a Smart Phone
3
08
Pic1 Pic2 Pic3
2. In System Setup>Network Setup page, please tick off DHCP, click Apply.
Then, please select DHCP again, click OK.
3.Power off the NVR by removing the power cable. Then, plug it in again to
re-power the unit. NVR will re-boot.
4.Wait 2-3 minutes then repeat steps 1-2. If the problem remains please contact
the Smonet Customer Service Team.
Viewing on PC by Eseecloud Software
4
Please contact seller for Eseecloud software.
Install Eseecloud Software first.
The default setting of Eseecloud software is no password under admin account,
please.
Select “Add” at upper right corner.
In the “Add device” box, select Cloud ID. Enter the cloud ID(9 or 10 numbers). You
can find it at the bottom right side of your home monitor screen.
Username is NVR system user name on your home monitor screen.(If you don’t
change it in your setup, it should be admin)
Password is your NVR system password on your home monitor screen.(If you
don’t change it in your setup, it should be blank, no password)
Channels: Input 4 or 6 or 8. If you have 4 cameras, enter 4 etc.
Click Finish, the device will be added successfully.
09
Autres manuels pour 2PCS
1
Ce manuel convient aux modèles suivants
10
Table des matières
