Smeg AS28I96L Manuel utilisateur

Contents

1. INSTRUCTIONS FOR SAFE AND PROPER USE _______________19

2. INSTALLATION OF THE APPLIANCE ________________________21

3. ADAPTING TO DIFFERENT TYPES OF GAS __________________25

4. FINAL OPERATIONS______________________________________28

5. USE OF THE COOKING HOB_______________________________29

6. CLEANING AND MAINTENANCE ____________________________31

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES WHOSE

IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS MANUAL.

INSTRUCTIONS FOR THE INSTALLER: these are for the qualified

technician who must carry out a suitable check of the gas system,

install the appliance, set it functioning and carry out an inspection test.

INSTRUCTIONS FOR THE USER: these contain user advice,

description of the commands and the correct procedures for cleaning

and maintenance of the appliance.

Introduction

1. INSTRUCTIONS FOR SAFE AND PROPER USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND

THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE

PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE

ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS

THEREIN BEFORE USING THE COOKING HOB. ALSO KEEP THE SERIES

OF NOZZLES SUPPLIED. INSTALLATION MUST BE CARRIED OUT BY

QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN

FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USES AND

CONFORMS TO CURRENT REGULATIONS IN FORCE. THE APPLIANCE

HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS:

COOKING AND HEATING-UP OF FOOD. ALL OTHER USES ARE

CONSIDERED IMPROPER.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR

IMPROPER USE.

DO NOT LEAVE THE PACKING IN THE HOME ENVIRONMENT.

SEPARATE THE VARIOUS WASTE MATERIALS AND TAKE THEM TO

THE NEAREST SPECIAL GARBAGE COLLECTION CENTRE.

IT IS OBLIGATORY FOR THE ELECTRICAL SYSTEM TO BE GROUNDED

ACCORDING TO THE METHODS REQUIRED BY SAFETY RULES.

THE PLUG TO BE CONNECTED TO THE POWER CABLE AND THE

SOCKET MUST BE THE SAME TYPE AND MUST CONFORM TO

CURRENT REGULATIONS.

NEVER UNPLUG BY PULLING ON THE CABLE.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION

TEST OF THE COOKING HOB, FOLLOWING THE INSTRUCTIONS

BELOW. SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT

FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE

CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE POSITION

OR 0(OFF) WHEN YOU FINISH USING THE HOB.

THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER

AND MARKING IS CLEARLY VISIBLE UNDER THE CASING.

THE PLATE ON THE CASING MUST NOT BE REMOVED.

Introduction

DO NOT PUT PANS WITHOUT PERFECTLY SMOOTH AND FLAT

BOTTOMS ON THE COOKING HOB GRIDS.

DO NOT USE RECIPIENTS OR GRIDDLE PLATES THAT EXTEND

BEYOND THE EXTERNAL PERIMETER OF THE HOB.

THE HOB IS TO BE USED BY ADULTS ONLY.DONOTLET

UNSUPERVISED CHILDREN PLAY WITH THE HOB.

REPLACED APPLIANCES MUST BE TAKEN TO A SPECIAL GARBAGE

COLLECTION CENTRE.

The manufacturer declines all responsibility for damage to

persons or things caused by non-observance of the above

prescriptions or by interference with any part of the appliance or by

the use of non-original spares.

Instructions for the installer

2. INSTALLATION OFTHE APPLIANCE

Installation must be carried out by a qualified technician in compliance

with applicable regulations in force.

2.1 Positioning

The following operation requires building and/or carpentry work so must

be carried out by a competent tradesman.

Installation can be carried out on various materials such as masonry,

metal, solid wood or plastic laminated wood as long as they are heat

resistant (T 90°C).

2.1.1 Fixing

Insert screws Aof the brackets provided into slots Bunder the appliance.

Slide the brackets into slots B. Position the appliance on to the support

frame and secure it by means of screws C.

To connect the appliance to the mains, holes have to be made in the

cabinet which vary from model to model. The dimensions of these

openings are shown by the areas marked in dotted lines in the diagrams

below.

Instructions for the installer

2.2 Electrical connection

Make sure that the voltage and capacity of the power line conform to the

data shown on the plate located under the casing. Do not remove this

plate for any reason.

The plug on the end of the supply cable and the wall socket must be the

same type and conform to the current electrical system regulations.

Check that the power line is adequately grounded.

On the power line, install an omnipolar cut-off device with contact cut-off

distance greater than or equal to 3 mm, located in an easily accessible

position near the unit.

Do not use reducers, adapters or shunts.

If the power cable is replaced, the wire section on the new cable must

not be less than 0.75 mm2(3 x 0.75 cable), keeping in mind that the end

to be connected to the hob must have the ground wire (yellow-green)

longer by at least 20 mm. Use only H05V2V2-F cable or similar which has

a maximum temperature of 90°C. Any replacement needed should be

carried out by a specialised technician who should make the mains

connections according to the following diagram.

L=brown

N=blue

= yellow-green

The manufacturer will not be liable for any damage to persons or

property caused by non-observance of the above instructions or deriving

from the tampering of even a single part of the hob.

Instructions for the installer

2.3 Ventilation of rooms

The hob may be installed only in rooms with permanent ventilation, as

required by standards regulations in force. The room in which the hob is

installed must have sufficient air flow to satisfy the requirements of

normal gas combustion and of necessary air exchange in the room. The

air intakes, protected by screens, must be appropriately sized

(regulations in force) and placed so as not to be blocked in any way.

The room where the oven is installed should be suitably ventilated to

avoid overheating or excess humidity produced by cooking, and in the

case of lengthy use a window should be opened or the speed of any

ventilators should be increased.

2.4 Discharge of combustion products

Discharge of combustion products must be guaranteed by means of

hoods connected to a natural draught flue with certain efficiency, or by

means of forced aspiration. An efficient aspiration system requires

careful planning by a specialist capable of installing it, respecting the

positions and distances prescribed by standards. After installation, the

installer must issue a certificate of conformity.

Instructions for the installer

2.5 Gas connection

Connection to the gas mains may be made with a rigid copper pipe or

with a flexible pipe and conforming to the provisions defined by standard

regulations in force.

To facilitate connection, fitting Aon the rear of the appliance may be

adjusted laterally. For this purpose, loosen hexagon nut B, turn fitting A

to the desired position, and retighten hexagon nut B(tightness is ensured

by a biconical brass ring). Use a soapy solution to check for proper

tightness. Never use a free flame.

The hob has been inspected for G20 (2H) natural gas at a pressure of

20 mbar. For use with other types of gases, see Section “3. ADAPTING

TO DIFFERENT TYPES OF GAS”. The gas intake fitting is ½” gas

external threaded (ISO 228-1).

Connection with rigid copper pipe:

the connection to the gas mains must

not provoke stress of any kind on the

hob.

Connection may be made by using

biconical adapter Dwith insertion of

gasket C(supplied).

Connection with flexible pipe: use

only flexible pipes conforming to

standard regulations in force, inserting

gasket C(supplied) between fitting A

and flexible pipe E.

The flexible pipe has to be installed so that pipe length does not exceed

1.5 meters of maximum extension. Make sure that the pipes do not touch

any moving parts or become damaged.

2.6 Connection to LPG

Use a pressure regulator and make the connection to the tank according

to the provisions of standards regulations in force. Make sure that feed

pressure conforms to the levels shown in the table in paragraph “3.2

Regulation for LPG”.

Instructions for the installer

3. ADAPTINGTO DIFFERENTTYPES OF GAS

Before any intervention, disconnect the power supply of the device.

The cooking hob is inspection-tested for use with G20 (2H) natural gas

at a pressure of 20 mbars. If used with other types of gas, you have to

replace the nozzles and regulate the primary air to the burners. Then

regulate the minimum flame on the gas taps. For nozzle replacement and

burner adjustment you must raise the cooking hob as described in the

following paragraph.

3.1 Removing the top

1. Slide out the grids, and remove all burner caps, flame cap crowns

and burners.

2. Remove the screws and nuts Awhich hold burner supports in place.

3. Remove plates B.

4. Lift up top Cwith the aid of a screwdriver and remove it from its seat.

5. Replace the burner nozzles according to the specifications in the

reference gas table.

6. Adjust primary air as described in paragraph “3.2 Regulation for

LPG”.

Instructions for the installer

3.2 Regulation for LPG

Loosen screw Aand push air

regulator Bto the bottom.

Witha7mmwrench,removenozzle

Cand replace it with the proper one

(follow the instructions on the

reference tables for the type of gas

to be used).

The torque wrench setting of the

nozzle must not exceed 3Nm.

Regulate the air by sliding regulator

Buntil reaching distance “X” shown

in the table in paragraph “3.4

Regulation of primary air”.

Lock regulator Bby tightening

screw A.

Burner Rated

heating

capacity

(kW)

LPG – G30/G31 28/37 mbar

Nozzle

diameter

1/100 mm

By-pass

1/100

Reduced

flowrate

(W)

Flowrate

g/h G30 Flowrate

g/h G31

Top with front controls:

Auxiliary 1.05 48 33 420 76 75

Semi rapid 1.65 62 33 420 120 118

Rapid 2.55 75 50 900 185 182

Ultrarapid 3.25 85 68 1500 236 232

Top with side controls:

Auxiliary 1.05 48 33 450 76 75

Semi rapid 1.65 62 33 450 120 118

Rapid 2.55 75 45 800 185 182

Ultrarapid 3.25 85 65 1500 236 232

Instructions for the installer

3.3 Regulation for natural gas

The hob has been inspected for G20 (2H) natural gas at a pressure of

20 mbar. To allow the unit to work with this type of gas, perform the same

operations described in paragraph “3.2 Regulation for LPG”, but choose

the nozzles and regulate the primary air for natural gas, as shown in the

following table and in paragraph “3.4 Regulation of primary air”.

Burner Rated

heating

capacity

(kW)

Natural gas – G20 20 mbar

Nozzle diameter

1/100 mm Reduced flowrate

(W)

Top with front controls:

Auxiliary 1.05 73 380

Semi rapid 1.65 92 420

Rapid 2.55 115 650

Ultrarapid 3.25 130 1400

Top with side controls:

Auxiliary 1.05 73 380

Semi rapid 1.65 92 450

Rapid 2.55 115 650

Ultrarapid 3.25 130 1400

3.4 Regulation of primary air

Referredtodistance“X” in mm.

BURNER G20

20 mbar G30/G31

28/37 mbar

Top with front controls:

Auxiliary 2.5 2.5

Semi rapid 1.5 2

Rapid 2.5 2

Ultrarapid 1.5 2.5

Top with side controls:

Auxiliary 3 3

Semi rapid 21.7 (*)

Rapid 32.5

Ultrarapid 1.7 3 (**)

(*) Semi rapid, rear: 2.5

(**) Ultrarapid, front: 4

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Smeg Plaque

Smeg

Smeg P1640X Manuel utilisateur

Smeg

Smeg SIHP3+WG4 Manuel

Smeg

Smeg Dolce Stil Novo PV695LCNXAU Manuel utilisateur

Smeg

Smeg Hob Manuel utilisateur

Smeg

Smeg SIB2741D Manuel utilisateur

Smeg

Smeg AP2640TC1 Manuel utilisateur

Smeg

Smeg SE264TD1 Manuel utilisateur

Smeg

Smeg PV164CN2AU Manuel utilisateur

Smeg

Smeg SI5643B Manuel utilisateur

Smeg

Smeg PS9R-3 Manuel utilisateur

Smeg

Smeg Piano P705ES Manuel utilisateur

Smeg

Smeg PGF32GNL Manuel utilisateur

Smeg

Smeg SI1F7955B Manuel utilisateur

Smeg

Smeg Dual Fuel Range Cooker B102MFX5 Manuel utilisateur

Smeg

Smeg SI1M4854D Manuel utilisateur

Smeg

Smeg PGF75-4 Manuel utilisateur

Smeg

Smeg Electric Built-in Hob Unit SE2755PS Manuel d'utilisation

Smeg

Smeg P755ABBN Manuel utilisateur

Smeg

Smeg PVL675LCN Manuel utilisateur

Smeg

Smeg PTSA727X Manuel utilisateur

Smeg

Smeg CIR597X Manuel utilisateur

Smeg

Smeg Dolce Stil Novo Series Manuel utilisateur

Smeg

Smeg SEI5632D Manuel utilisateur

Smeg

Smeg SI2741D Manuel utilisateur

Manuels Plaque populaires d'autres marques

Siemens

Siemens EX875KYV1E Fiche technique

AEG

AEG CERAMIC HOB 6010 K Manuel utilisateur

VALERA

VALERA CT 70A Manuel utilisateur

Zanussi

Zanussi ZGF 6420 Manuel utilisateur

Gaggenau

Gaggenau CI 273 Manuel utilisateur

G3 Ferrari

G3 Ferrari Energy Manuel utilisateur

Pkm

Pkm IN4B Manuel utilisateur

Award

Award H903BG Manuel utilisateur

Zanussi

Zanussi VCH 5005 RZ Manuel utilisateur

Miele

Miele KM 523 Manuel utilisateur

Hotpoint

Hotpoint IS67V8CCXT/E Manuel utilisateur

AEG

AEG HK854870XB Manuel utilisateur

Cookology

Cookology SEP600BK Manuel utilisateur

Bauknecht

Bauknecht Hob Manuel utilisateur

Zanussi

Zanussi ZGM 782 Manuel utilisateur

dipo INDUCTION

dipo INDUCTION DIBK218S Manuel utilisateur

Miele

Miele KM 5987 Manuel utilisateur

Miele

Miele KM 360 G Manuel utilisateur