SMD SM4247 Manuel utilisateur
SMART MOTOR DEVICES
http://www.smd.ee
Stepper motor SM4247 with integrated driver SMD-1.6 mini IP65
manual
SM4247/SMD.16mini.IP65.002
2019
Tallinn Science Park Tehnopol, Mäealuse st. 4, Tallinn
12618, Estonia Phone: + 372 6559914,
e-mail: sale@smd.ee
url: http://smd.ee
1. Product designation
This device is a stepper motor SM4247 with an integrated control unit SMD-1.6 mini with protection
IP65. Stepper motor is intended for transformation of control signals in angular movement of the rotor with its
fixation in the given position without feedback devices. Integrated control unit SMD-1.6 mini is an electronic
device mounted on the motor SM4247 housing and is intended for this motor control.
2. Technical characteristics Table 1. Technical characteristics.
Motor phase current, Amp 1.6
Holding torque, kgf∙cm
1
4.4
Protection class IP65
Rotor inertia, g∙cm
2
68
Microstepping modes 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/128, 1/256
Power supply voltage, VDC stabilized 12 - 48
Max. radial force (20 mm from the flange), N 28
Max. axial force, N 10
Shaft radial play, no more, mm 0.02
Shaft axial play, no more, mm 0.08
Step angle accuracy ±5% relative to the whole step
Phase resistance, Ohm 0.8
Phase inductance, mH 3.5
Temperature Rise, °C 80
Average resource, hours 20000
1Holding torque – the motor is powered but doesn’t rotate
3. Control signals – oscillogram, schemes, connection diagrams
Img.1. «STEP» and «DIR» signals order and duration
Tallinn Science Park Tehnopol, Mäealuse st. 4, Tallinn
12618, Estonia Phone: + 372 6559914,
e-mail: sale@smd.ee
url: http://smd.ee
Img.2. Connection scheme
Table 2. Contacts assignment.
Contact
number Assignment n
1
-
U
supply
(
12
…
48
VDC
)
2
-
Fault (
error indica
tion
)
3
+ COM (
common contact of the control interface
)
4
Setup (
input of operation parameters
)
5
+ U
supply
(12
…
48
VDC
)
6
-
Step 5V
7
-
Step 24V
8
-
Dir 5V
9
-
Dir 24V
Img. 3. Control signals circuits.
Tallinn Science Park Tehnopol, Mäealuse st. 4, Tallinn
12618, Estonia Phone: + 372 6559914,
e-mail: sale@smd.ee
url: http://smd.ee
4. Dimensions
Img.4. Dimensions of stepper motor SM4247 with integrated driver SMD-1.6 mini IP65
5. Configurating of the driver
The 4th contact «SETUP» of the input connector is intended to configure the built-in driver. Duration of
the signal «Setup» is not less than 100 ms, pulse-to-pulse spacing is no more than 3 s. To make the
configuration process easier, connect a button «Setup» according the connection scheme on Img. 3.
Driver setting parameters are indicated by 2-color LED. Number of red blinks indicates the parameter
number, green blinks - parameter value. Correspondence between the color indication and driver settings is
shown in the table 3. Default values of parameters are shown in bold and underlined.
Table 3. correspondence of LED indication and driver settings
Number of red blinks / parameter
number Meaning Number of green blinks / parameter
value Meaning
1 Microstepping
1 1
2 1/2
3 1/4
4 1/8
5 1/16
6 1/32
7 1/128
8 1/256
2 Holding current
1 10%
2 20%
3 30%
4 40%
5 50%
6 60%
7 70%
8 80%
9 90%
10 100%
3Rotation
direction 1 Not inversed
2 Inversed
To enter the configurating mode press and hold «SETUP» button (or hold a signal at the «SETUP»
input) for no less than 3 s. After entering cofigurating mode the green LED blinks off, the driver is waiting for
entering of a parameter number. The parameter number is set by short signals at «SETUP» input (or
«SETUP» button). Every signal impulse is indicated by green LED blink.
After entering the number of the setting parameter wait for 3 s. The single red LED flash indicates
accepting of the parameter number and readiness to get the parameter value. Entering of the parameter value
is the same as entering the parameter number.
Tallinn Science Park Tehnopol, Mäealuse st. 4, Tallinn
12618, Estonia Phone: + 372 6559914,
e-mail: sale@smd.ee
url: http://smd.ee
6. Environmental conditions:
SMD-1.6mini IP65 with motor SM4247 is designed to operate in operating mode S1 (24 hours/day)
under thenext conditions:
·Ambient environment: non- corrosive, non-explosive,
·Humidity: 90% RH or less upon condition +25°C
·Condensation and freezing: none
·Pressure: 650…800 mm of mercury.
·Ambient Temperature: 0…+40°C
7. Delivery in complete sets
Stepmotor SM4247 with integrated driver SMD-1.6 mini IP65 1 pcs
Manual SM4247/SMD.16mini.IP65.002 1 pcs
9. Warranty
Any repair or modifications are performed by the manufacturer or an authorized company.
The manufacturer guarantees the failure-free operation of the controller for 12 months since date of sale
when the operation conditions are satisfied.
The manufacturer sales department address:
Smart Motor Devices OÜ,
Tallinn Science Park Tehnopol, Mäealuse st. 4, Tallinn 12618, Estonia,
Phone: + 372 6559914,
e-mail: mai[email protected]
url: http://smd.ee
Date of sale:
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels SMD Moteur
