SMC Networks SMC-520 Manuel utilisateur

SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu

SMC-520

TEMPERATURE & HUMIDITY SENSOR

USER GUIDE

SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu

Notice

The information in this User Guide is subject to change without notice.

Not all the features described in this manual are available in all hardware and firmware versions.

Please check with SMC for details of model specific features such as measurement parameters and

Protocol support.

This document is property of SMC and shall not be reproduced in any form without written approval

from SMC.

SMC Ship Motion Control is not responsible for any errors in this manual or their consequences.

SMC Ship Motion Control Ltd

Email: info@shipmotion.eu

Web: www.shipmotion.eu

Tel: +46 8 644 5010

 
3 
SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu 
 
TABLE OF CONTENTS 
1INTRODUCTION.................................................................................................................... 4 
1.1 RECEIVING THE TEMPERATURE AND HUMIDITY SENSOR....................................................................... 4 
1.2 SMC-520 DIMENSIONS ................................................................................................................ 5 
1.3 INSTALLATION.............................................................................................................................. 6 
1.3.1 INSTALLATION LOCATION RECOMMENDATIONS.......................................................................... 6 
1.4 MOUNTING INSTRUCTIONS USING SOLAR RADIATION SHIELD .............................................................. 7 
1.5 ELECTRICAL COMMUNICATION ....................................................................................................... 9 
1.6 SMCINSTRUMENTS CONFIGURATION SOFTWARE ........................................................................... 10 
1.6.1 DEFAULT SETTINGS AT THE FACTORY...................................................................................... 10 
1.6.2 GENERAL INFORMATION CONFIGURATION SOFTWARE.............................................................. 11 
2SERIAL OUTPUT STRINGS.................................................................................................... 13 
2.1.1 WIXDR............................................................................................................................ 13 
2.1.2 VAISALA HMP155 FORMAT ................................................................................................ 13 
3CONFIGURATION COMMANDS ........................................................................................... 14 
3.1 REPLIES FROM THE SMC-520...................................................................................................... 14 
4MAINTENANCE................................................................................................................... 15 
5SERVICE AND WARRANTY................................................................................................... 15 
5.1.1 LIABILITY........................................................................................................................... 16 
5.1.2 RESTRICTION OF WARRANTY ................................................................................................ 17 
5.2 TECHNICAL SUPPORT .................................................................................................................. 17 
6TECHNICAL SPECIFICATIONS SMC-520 ................................................................................. 18 
7FAQ AND SUPPORT............................................................................................................. 19

SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu

1INTRODUCTION

The SMC-520 Temperature and Humidity sensor is an accurate, reliable and cost effective way to

measure the air temperature and humidity for many applications.

The data transmitted from the SMC Temperature and Humidity sensor is in a standard NMEA

sentence format over RS232 and RS485 that can be used by many systems as well as SMCs

Monitoring System applications for graphical presentation and data logging, listed below.

•SMChms, Helideck Monitoring System

•SMCems, Environmental Monitoring System

•SMCwms, Weather Monitoring System

The SMC-520 is produced to be used in outdoor applications. The optional SMC-560 Solar radiation

shield provides accurate temperature readings also in sunny environments. The SMC-520 uses a

PT1000 element for the temperature measurements.

1.1 RECEIVING THE TEMPERATURE AND HUMIDITY SENSOR

Unpack the equipment and remove all the packaging materials and shipping carton.

The SMC-520 sensor is delivered in a cardboard box designed to protect it from damage during

transit.

When the sensor has been received, it must be inspected for damage during shipment. If damage has

occurred during transit, all the shipping cartons and packaging materials should be stored for further

investigation. If damage is visible, a claim for shipping damage must be filed immediately.

Standard Delivered Items

•Temperature and Humidity Sensor

•Calibration Certificate

•SMC Instruments Configuration software and User Manual

•Cable with M12 connector, 3 m cable standard

Optional Items

•SMC-560 Solar Radiation Shield including Pole mounting brackets

•M12, 8 pin connector on a 5m cable

•M12, 8 pin connector on a 10m cable

SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu

1.2 SMC-520 DIMENSIONS

All dimensions are in mm

SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu

1.3 INSTALLATION

SMC highly recommend that the SMC-520 Temperature and Humidity sensor is deployed on site

inside a solar radiation shield such as the SMC-560 to achieve the optimum performance from the

sensor.

The sensor can also be installed without the shield inside a Stevenson screen.

It is not recommended to mount the sensor outside unshielded.

SMC-560 Solar Radiation Shield

1.3.1 INSTALLATION LOCATION RECOMMENDATIONS

Install the SMC-520 Temperature and Humidity sensor in an area with free air flow. Avoid positioning

the sensor in position that would not be representative of the area to be measured. Where possible

the sensor should be mounted away from heat sources, either direct such as exhausts or reflected

such as building walls. Placing the sensor to close to the ground may lead to inaccurate

measurements.

SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu

1.4 MOUNTING INSTRUCTIONS USING SOLAR RADIATION SHIELD

The SMC-560 Solar radiation shield is designed to be mounted on a pole of 30 to 60mm diameter.

After the shield has been attached to the pole, the Temperature and Humidity sensor is to be fitted

into the shield until the wider part of the sensor reach the compression fitting. Tighten the

compression fitting to hold the sensor in place. It is normally enough to tighten the fitting by hand.

After mounting in the shield connect the cable to the sensor.

SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu

1.5 ELECTRICAL COMMUNICATION

M12, 8 pin male connector on the SMC-520 schematic layout

Free cable end wire color

Sensor function

Details

White

Signal Ground

Brown

RS232 Tx

default 38400 8N1

Green

RS232 Rx

Yellow

Ground

Gray

VDC -

Pink

RS485 Data+

default 38400 8N1

Blue

RS485 Data-

Red

VDC+

Power input 12…30 VDC

Note: Please pay special attention to the SMC-520 wire colours, as applying voltage to the data wires

may damage the sensor.

The serial communication over RS232 and RS485 can be configured for the following baudrates 4800,

9600, 19200, 38400 and 57600 bps from the SMC Configuration software. The SMC-520 is set to

automatically output the strings in the selected data format in the selected output rate.

SMC-520 User Guide revision 1.3 SMC Ship Motion Control www.shipmotion.eu

1.6 SMC INSTRUMENTS CONFIGURATION SOFTWARE

The SMC configuration software is a PC application, after the sensor serial communication has been

connected the SMC Configuration Software can be used to set the sensor configuration and

communication parameters according to requirements.

The settings entered in the SMC Configuration software are written to the sensor. The settings are

stored in flash memory inside the sensor and are not dependent on power supply or battery power.

1.6.1 DEFAULT SETTINGS AT THE FACTORY

The sensor is delivered from SMC with a set of default parameters which can be changed from the

SMC IMU Configuration Software.

The factory default communication settings are as follows.

Baud Rate 38400

8 Databits

No parity

1 stop bits

Table des matières

Autres manuels SMC Networks Accessoires

SMC Networks

SMC Networks PSE57 Series Manuel utilisateur

SMC Networks

SMC Networks PSE530 Series Mode d’emploi

SMC Networks

SMC Networks D-MP Series Manuel utilisateur

SMC Networks

SMC Networks PFMV505 Manuel utilisateur

SMC Networks

SMC Networks IMU-007 Manuel utilisateur

SMC Networks

SMC Networks PFM5 Series Manuel utilisateur

SMC Networks

SMC Networks PSE510 Series Manuel utilisateur

SMC Networks

SMC Networks PSE200 Series Manuel utilisateur

SMC Networks

SMC Networks ISA2 Series Manuel d'installation

SMC Networks

SMC Networks SMCMT01-Z Manuel de l'opérateur

SMC Networks

SMC Networks D-MP Series Manuel utilisateur

SMC Networks

SMC Networks XT477-4-X2 Manuel utilisateur

SMC Networks

SMC Networks MHT2 Manuel utilisateur

SMC Networks

SMC Networks HRGC001-A Series Manuel utilisateur

SMC Networks

SMC Networks HRG001-W Manuel utilisateur

SMC Networks

SMC Networks IZD10-*10 Series Manuel utilisateur

SMC Networks

SMC Networks PFMV5 Series Manuel utilisateur

SMC Networks

SMC Networks PSE575 Manuel utilisateur

SMC Networks

SMC Networks SMCGB10-Z Manuel utilisateur

SMC Networks

SMC Networks PFM5 Series Mode d’emploi

SMC Networks

SMC Networks XT477 Manuel utilisateur

SMC Networks

SMC Networks PSE570 Manuel utilisateur

SMC Networks

SMC Networks PSE550 Manuel utilisateur

SMC Networks

SMC Networks PFMV5 Series Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur