Smartek NB40PP Manuel utilisateur

NB40PP

REV 02 – November 2019 - ENGLISH

NUBI 4.0 – PLUG & PLAY

Model: NB40PP

Power suppl : 3,6V lithium batter

PIR: YES

Thank ou for purchasing NUBI 4.0, the wireless,

intelligent and Plug & Pla securit smoke screen device. It

can be used with an anti-theft s stem, coupling the device

to an internal siren.

WE RECOMMEND THAT YOU READ THE

ENTIRE MANUAL BEFORE PROCEEDING TO

PRODUCT INSTALLATION.

1. OVERVIEW

The device is powered b a 3.6V AA size lithium batter

supplied with the product, such as SAFT LS14500 or

similar. This batter provides the necessar energ to the

device for a period of 10 ears. The ignition of the smoke

cartridge is ensured even when the batter is ver low

(2.2V). When the batter is about to run out, the device will

beep ever hour.

NUBI 4.0 efficientl protects volumes up to 100 m3. The

smoke generated b NUBI 4.0 is based on incense and

does not produce toxic atmosphere as tested according to

the TLV-STEL directive EU 2017/164 and ACGIH. After use

the room must be ventilated before sta ing there.

The device is completel wireless, it can be installed onl

with two dowels. In the same room where NUBI 4.0 is

installed, an internal siren is required. Programming

operations are not necessar on the burglar alarm control

panel. The sound of the siren is digitized during the pairing

operation to be performed during installation. Thanks to

digital learning, sounds other than the specific coupled

siren will not produce an effect, even the sound of the

same siren model, but installed in a different room, will not

activate NUBI 4.0.

While the coupled siren sounds, NUBI 4.0 switches to the

"active state" and as soon as it detects movement with its

infrared sensor it triggers the emission of smoke. It is

possible to extend the "active state" of NUBI 4.0 for 5

minutes even after the siren has stopped sounding (see

chapter 6: select the operating mode).

For the first 20 minutes after performing the siren coupling

operation, or inserting the power suppl batter , it is

possible to perform the functional test of NUBI 4.0 without

causing smoke emission.

The smoke cartridge works onl once, the smoke

emission, when triggered, can no longer be interrupted.

The replacement of the smoke cartridge is ver simple, the

conductors of each cartridge end with the activation card

which will be easil plugged into the appropriate connector

on the motherboard.

NUBI 4.0 is a famil of products, in addition to the Plug &

Pla version, other models are available to be connected

to the alarm control panel through the inputs and outputs.

The are available with 12V power suppl or batter , with

or without built-in infrared sensor. For more information,

visit www.smarteksrl.it.

2. INSTALLATION

NUBI 4.0 can be easil

installed on the wall or

even in a corner at a

height between 150 and

250 cm.

WARNING

Do not insert an obstacle at a distance of less than 1.5

meters from the smoke outlet hole.

The best performance is achieved when the jet of smoke

coming out from NUBI 4.0 directl hits the floor, in this wa

the smoke will cool and spread better.

NUBI 4.0 Plug & Pla must be installed in the same room

where an internal alarm s stem siren is located.

Do not place NUBI 4.0 in particularl nois places, as well

as near strong sound sources, such as television or

speakers. Strong and continuous sound sources will

reduce batter life.

The distance between NUBI 4.0 and the siren should be

approximatel between 0.5 and 2 m, but this parameter

strongl depends on each siren. In principle it is better to

keep the siren close to NUBI 4.0 to obtain better noise

immunit , but if it is too close it could be reached b an

excessive sound level or influenced b sound reflection

phenomena.

To obtain maximum immunit to anomalies due to ambient

sound reflections, it is recommended to install the siren

and NUBI 4.0 at a height greater than 2 meters.

Before definitivel fixing NUBI 4.0 to the wall, proceed to

carr out the sound tests described in chapter 3 and 4

below.

3. TEST OF SOUND THRESHOLD

Open the box, insert the batter into the motherboard

without connecting the smoke cartridge, then close the

container. The green LED reports a sound level lower than

the 90Db threshold, the red one reports a higher level that

causes the device to wake up.

NB40PP

REV 02 – November 2019 - ENGLISH

Perform the sound tests with the closed box, so as to

simulate the real working condition.

For longer batter life, ambient noise should not frequentl

turn on the red LED, while it is essential that the sound of

the siren do it.

The LEDs are offset from the slots to allow the

best frontal observation.

4. TEST OF THE SIREN

This test controls if the sound level of the siren is suitable

to be digitized. Pressing the "PAIR" button alternates the

"sound threshold test" (blue LED off) and the "siren test"

(blue LED on).

1. Sound the siren

2. Hold the appliance in the installation position.

3. Press the "PAIR" button (blue LED ON).

4. Wait about 2 seconds

5. Observe the red and green LEDs:

# Red Green Result

1 SF OFF Sound too weak

2 SF ON Sound OK, but too weak

3 OFF ON Sound OK

4 FF ON Sound OK, but strong

5 FF OFF Sound too strong

SF = Slow flashing, FF = Fast flashing

Table 1: siren test result

Condition 3 is the ideal one, in conditions 2 or 4 the

appliance works, but if it is possible to improve the

positioning. In conditions 1 or 5 the positioning must

necessaril be modified.

To re licate the test in another osition:

•Reach the new location

•Press the "PAIR" button twice to reset the

previous test (blue LED OFF, blue LED ON)

•Wait 2 seconds and see the new result.

Once the sound tests have been erformed,

o en the device and remove the battery.

5. FIXING THE DEVICE

After opening the

top cover, fix the

lower part of the

box on the wall

using the holes

(A).

6. SELECT OPERATING MODE

Use the appropriate JUMPER to select whether to dela

the return of NUBI 4.0 to the "sleep mode" when the sound

of the siren ceases.

MODE1 => Jum er o ened => no delay

NUBI 4.0 will return to "sleep mode" at the end of the siren

sound, regardless of its duration.

MODE 2 => Jum er closed => 5' delay

When the duration of the sound of the siren does not

exceed the time recorded in the pairing phase, NUBI 4.0

will return to the "sleep mode" when the sound stops, as in

mode 1. Otherwise, if the duration of the sound of the siren

exceeds that recorded in the phase of pairing, NUBI 4.0

will remain active and will return to "sleep mode" 5 minutes

after the sound of the siren stops.

MODE 2 allows ou to discriminate between two

situations: an alarm caused b a user mistake, which

disarm the s stem within a reasonable time or a real alarm

that will last longer. During the 5 minutes after the end of

the siren sound, NUBI 4.0 will emit a short acoustic signal

ever 8 seconds to indicate that it is still active, a useful

signal especiall for the s stem owner.

7. INSTALL THE SMOKE CARTRIDGE

WARNING

Before mounting the smoke

canister, check the color of the

shock indicator. Do not mount the

smoke canister if the indicator is

stained red.

NB40PP

REV 02 – November 2019 - ENGLISH

1) Insert the smoke cartridge into its housing.

2) Insert the smoke cartridge connector into the

appropriate one on the motherboard.

WARNING

Remove the batter from the motherboard before

connecting the smoke cartridge and wait at least

10 seconds.

Finall close the box.

8. SIREN PAIRING

Perform this operation when both NUBI 4.0 and the siren

are fixed in the final position. Changing the installation

location after pairing will result in the failure of the siren

recognition. Press and hold the pairing button for 3

seconds, until the blue LED flashes and a beep is emitted.

NUBI 4.0 is now in pairing state.

When the red and green LEDs flash, wait a few seconds

for them to switch off before pressing the "PAIR" button.

Battery test: As soon as ou enter pairing state, the green

LED will light up for 5 seconds if the batter is charged, or

the red LED if it is exhausted.

Walk test: After the batter test, NUBI 4.0 will beep ever

time the integrated infrared sensor detects movement,

allowing the detector's range to be tested. The test ends as

soon as the siren sound recording starts or exited

prematurel from the pairing state.

Exit airing state: You can cancel the pairing state

before start recording the sound with a short press of the

“PAIR” button. In this case, an previousl stored siren

pairing will not be erased from the memor . It ma be

useful to exit prematurel from pairing state when ou want

to perform onl the walk test.

Pairing the siren: Sound the siren for at least 20 seconds

or for a longer time at will, especiall if ou have selected

MODE 2 for operation.

Avoid to stay close the device during

registration, this could alter its qualit . Look at the

result of digitization on the LEDs, after turning off

the siren.

The result of the recording is the one alread shown in

Table 1. When the sound of the siren stops, the LEDs will

remain lit for a minute to allow control. To switch them off

prematurel simpl press the "PAIR" button briefl . The

best result is that the blue and green LEDs are on and the

red LED is off.

9. PAIRING CHECK

The right siren pairing can be checked in the following

wa s:

With the NBCT test cartridge accessory:

The NBCT test

cartridge simulates the

behavior of the smoke

cartridge, but instead of

dispensing the smoke it

emits a series of beeps

and lights up its LEDs. NUBI 4.0 Plug & Pla with the test

cartridge is immediatel operational and ignores the 20

minute test time described below.

With the smoke cartridge su lied, but without

causing the emission of smoke:

For 20 minutes after pairing the siren, or after inserting the

batter , NUBI 4.0 enters a special "test mode". Regardless

of how the operating mode 1 or 2 is set, the behavior is

alwa s the following:

•When the siren sounds nothing happens, even

passing in front of the infrared sensor.

•If the siren sounds for a shorter time than the one

learned during the pairing phase, when the sound

stops NUBI 4.0 emits a series of beeps and

renew again 20 minutes to carr out a new test.

•If the siren sounds longer than the one learned

during the pairing phase, when the sound stops

NUBI 4.0 emits a beep ever 8 seconds and

remains active. When the infrared sensor detects

movement, NUBI 4.0 emits a series of beeps and

renew again 20 minutes to carr out a new test. If

no movement is detected for 5 minutes, NUBI 4.0

returns to the "sleep mode", still renewing the 20-

minute timer to perform a new test.

After 20 minutes from the last event that renew the timer

(power suppl , coupling with the siren or a test performed),

NUBI 4.0 enters into standard operating mode.

NB40PP

REV 02 – November 2019 - ENGLISH

10. OPERATING MODE

NUBI 4.0 is normall in "sleep mode". When it recognizes

the sound of the paired siren it goes into the "active state",

read to trigger the emission of smoke as soon as the

infrared sensor detects movement. When the sound of the

siren ends, NUBI 4.0 will return to "sleep mode"

immediatel or after 5 minutes, depending on the selected

operating mode 1 or 2 and the duration of the siren sound.

When it switches from "active state" to "sleep mode" it

alwa s emits a series of 8 beeps. When NUBI 4.0 remains

in the "active state" and the sound of the siren has ceased,

it emits a beep ever 8 seconds.

11. SMOKE CANISTER REPLACEMENT

Onl use original spare parts, remove the empt cartridge

and install the new one, as described in chapter 7.

12. MAINTENANCE

We recommend replacing the smoke cartridge ever 4

ears, using onl the original spare part.

If the installation place of the siren or NUBI 4.0 is changed,

carr out a new coupling.

If obstacles are inserted between the siren and NUBI 4.0,

such as bookcases or cabinets, proceed with a new

pairing.

In the case of using self-powered wireless sirens, alwa s

keep the siren batteries in good condition so that the do

not produce a distorted sound.

13. WARRANTY

SMARTEK s.r.l. It guarantees its products against all

manufacturing defects for a period of 30 months from the

production date shown on the label.

14. RECOMMENDATIONS

Before leaving, ventilate the rooms thoroughl after the

smoke has been delivered.

15. ADVANCED DIAGNOSTICS

Below we describe the behavior of the LEDs when an

advanced diagnostic operation is required:

PAIRING STATE:

The blue LED flashes. As soon as ou enter in pairing

state, the batter test is performed for 5 seconds: Green

LED ON = batter charged, red LED ON = batter to be

replaced. After the initial 5 seconds, when it receives

sound > 90db, in the first 5 seconds the blue LED will flash

ver quickl , if the sound stops the LED will return to

flashing normall . If the sound persists for more than 5

seconds, the blue LED lights up steadil indicating that the

recording phase has begun. When the blue LED is ON

stead and the green LED flashes the digitization of the

siren sound is finished, it is continuing to memorize the

pla ing time. At the end of the sound the blue LED is ON

and the result on the green and red LEDs as described in

table 1.

OPERATING MODE:

During the "test mode" (first 20 minutes), the red and

green LEDs flash alternatel to indicate that NUBI 4.0 is

anal zing a sound> 90db to recognize the siren.

The green LED flashes: NUBI 4.0 has recognized the siren

sound and it is in "active state".

16. TECHNICAL SPECIFICATIONS

Power suppl 3,6V lithium batter AA

Autonom 10 Years (*)

Size 12cm x 17cm x 14cm

Saturable volume 100m3

Weight 760g

Smoke average deliver time 25sec

Operating temperature From -20°C to +70°C

Maximum relative humidit 90%

(*) In a quiet environment

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur