Read the instructions before using the machine
1. Specication
Model No: BT-700D3(T)
Power Rate: 7000W
Voltage: 220-240V / 1N ~ 50/60 Hz
Temperature: 60°C - 240°C
2. Caution
• Do not plug in with wet hands.
• Do not plug into a socket where several other appliances are plugged in.
• Do not use if the plug cord is damaged or the power plug does not t the socket safely.
• Do not modify the parts, or repair the unit by yourself.
• Do not use the unit near ame or wet places.
• Do not use where children can easily touch the unit, or allow children to use the unit by
themselves.
• Do not place on unstable surfaces.
• Do not move the unit when the pot or the pan is on it.
• Do not heat the pot empty or overheat the pot.
• Do not place metallic objects such as knives, forks, spoons, lids, cans, and aluminum foils on
the top plate since they can get hot.
• Use the unit with sucient space around it. Keep the front side and either right or left side of
the unit clear.
• Do not use the unit on carpet or tablecloth (vinyl) or any other low-heat-resistant article.
• Do not place a sheet of paper between the pot or the pan and the unit. The paper may get
burnt.
• If the surface is cracked, switch o to avoid the possibility of electric shock and then take to
the service center immediately.
• Do not block air intake or exhaust vent.
• Do not touch the top plate right after removing the pot or the pan, as the top plate will still be
very hot.
• Do not place the unit near objects which are aected by magnets, such as: radios, televi-
sions, automatic-banking cards and cassette tapes.
• The power cord must be replaced by qualied technicians.
• CAUTION: Hot surface.
• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
• The temperature of accessible surfaces may be high when the appliance is operating.
• The appliance is not intended to be operated by means of an external timer or separate
remote control system.
• This product contains recyclable materials. Do not dispose this product as unsorted
municipal waste. Please contact your local municipality for the nearest collection point.
• Metallic objects such as kitchen utensils, cutlery etc. shall not be placed on the hob surface
within the cooking zones since they could get hot;
• Take care when operating the appliance, as rings, watches and similar objects worn by the
user could get hot when in close proximity to the hob surface
• Only use vessels of the type and size recommended.
• After use, switch the hob element o by means of its control. Do not rely on the pan detector.
• Appliance not to be cleaned with water jet.
• Any repairs shall be carried out only by persons trained or recommended by the
manufacturer.
• Care must be taken to ensure that the splash back and surrounding area free of metallic
surfaces
• Non-ionizing electromagnetic radiation, be careful.
• DANGER: High voltage.
• Appliance is not intended to be operated by means of an external timer or separate remote-
control system.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualied persons in order to avoid a hazard.
• Means for disconnection must be incorporated in the xed wiring in accordance with the
wiring rules
• Additional protective device of residual- current device of 30 mA shall be installed on the xed
wiring before connected to the xed wiring
Warning: Children should be supervised to ensure that they do not play with the appliance.
Power line connection
The using standard of power line is: 3G×4.0mm (core number × section).
When installation, please use special electricity air protection switch, and the switch must be
installed in a convenient or easy controlled place, and the installation place should reach a height
of 1.3M to 1.5M .The required electricity current of the switch is 35A.
The socket shall be connected according to the relevant standard or connected to a single-pole
cut-out. The method of connection is shown in Figure (3):
Voltage Power cord connection
