SLOC SPR-203 Manuel

SPR-203 Inbetriebnahme

INITIAL SETUP SPR-203

Version: 1.0 06/10/2020

SPR-203 Initial Setup

TABLE OF CONTENT

1. Introduction..........................................................................................................3

1.1. Commissioning steps..........................................................................................................3

1.2. Helpful documents ..............................................................................................................3

2. SLOC Device Management (SDM) .........................................................................4

2.1. First login to the SDM portal ...............................................................................................4

2.2. App Download & Installation...............................................................................................4

3. SLOC activating/deactivating................................................................................5

3.1. Activating: ............................................................................................................................5

3.2. Deactivating BLE Visibility:..................................................................................................5

3.3. Transport mode ...................................................................................................................5

4. SLOC Configuration..............................................................................................6

5. Check data transmission ....................................................................................13

5.1. Download and install demo app .......................................................................................13

5.2. Reading SPR-203 data with demo app.............................................................................13

6. Mounting............................................................................................................16

6.1. SPR-203..............................................................................................................................16

6.2. SPR-203 Reference............................................................................................................17

7. Read out the data via BLE ...................................................................................18

7.1. Package structure..............................................................................................................18

7.2. MAC - Adress .....................................................................................................................18

7.3. Type ....................................................................................................................................19

7.4. Loading status ...................................................................................................................19

7.5. Motion state.......................................................................................................................19

7.6. Lifting height ......................................................................................................................20

7.7. Distance in mm..................................................................................................................20

7.8. Acceleration (shock) .........................................................................................................20

7.9. Battery status in percent...................................................................................................21

7.10. Current position .................................................................................................................21

8. Legal regulations................................................................................................22

8.1. Declaration of conformity .................................................................................................22

8.2. Copyright ............................................................................................................................23

8.3. Disposal..............................................................................................................................23

SPR-203 Initial Setup

1. Introduction

Thank you very much for choosing SLOC.

In this documentation you will learn how to put your product into operation and evaluate

the data.

We at SLOC are always trying to make our products as simple and intuitive as possible.

However, should you encounter any problems, we are at your disposal.

E-Mail Adress: sup[email protected]

1.1. Commissioning steps

The following steps must be completed to successfully configure the SLOC device:

1. Visit support.sloc.one

2. Download the commissioning documentation

3. Login/registration in the SDM portal (Chapter 2.1)

4. SDM app installation on the Android device (Chapter 2.2)

5. Wake up the SLOC with the magnet (Chapter 3)

6. Configuration of the SLOC with the SDM app (Chapter 4)

7. Check data transmission (Chapter 5)

8. Mounting the SLOC on the vehicle (Chapter 6)

9. Read out the data via BLE (Chapter 7)

1.2. Helpful documents

Download SLOC Software-Manual

SPR-203 Initial Setup

2. SLOC Device Management (SDM)

SLOC Device Management consists of a web portal (https://sdm.sloc.one/) and an Android

app, which is needed for the configuration.

2.1. First login to the SDM portal

If you purchase your products through SLOC, you have been sent a registration email to

If you purchase the product via an external platform, please use the e-mail address with

which the order was placed. You will find the password in the product packaging on the

enclosed info sheet. You will then receive a registration link and can assign your password.

(Login Screen)

(SDM Portal Homepage)

2.2. App Download & Installation

The app can be downloaded to a smartphone/tablet via the SLOC Support Center

(https://support.sloc.one) on a smartphone/tablet by clicking on your product (SPR-203)

and then downloading the APK file. This can be done directly from the smartphone/tablet

or via a PC and USB cable. Afterwards the app can be installed.

For more information on APK installation, please refer to chapter 3 of the SLOC Software Manuals at support.sloc.one.

SPR-203 Initial Setup

3. SLOC activating/deactivating

3.1. Activating:

To configure a SLOC, the transport mode of the SLOC must first be deactivated and/or the

BLE visibility must be activated.

To do this, the magnet (included in the scope of delivery) must be placed on that side of the

SLOC for at least 2s and, if necessary, moved back and forth on which the magnet symbol

is shown (see illustration).

3.2. Deactivating BLE Visibility:

BLE communication is automatically disabled after 60 seconds. After that it can be

reactivated with the magnet (see chapter 3.1).

3.3. Transport mode

The transport mode is the mode in which the SLOC is sent (i.e. the SLOC measures and

sends no data and consumes no power).

To put an activated SLOC back into transport mode, select the SLOC in the SDM app and

click the button "Transportmode on" under "ADVANCE".

SPR-203 Initial Setup

4. SLOC Configuration

On the following pages the configuration is explained step by step with pictures.

IMPORTANT:

Be sure to configure the SLOC before assembly (see Chapter 5) and check the data

transmission (see Chapter 4).

NOTE:

The BLE of the SLOC is deactivated after 60 seconds. If a SLOC is no longer accessible while

using the app, wake it up again with the magnet (see chapter 2.1.).

Registration in the SDM App:

Use SLOC Device Management login data (see

Chapter 1).

SPR-203 Initial Setup

1. SETTINGS:

- Server must be https://sdm.sloc.one

- Other settings as in the picture on the left

API Key, Organization UUID, Organization

and Privileges vary depending on the app

token used

2. Scan environment for SLOCs:

Wake up SLOC (see Chapter 2)

Then



Click on SCAN

SPR-203 Initial Setup

3. SLOC selection:



Selection of the SLOCs

using the MAC address

(see sticker on SLOC)

Note:

The BLE of the SLOC is deactivated after 60 seconds. If

the app cannot establish a connection, the SLOC must

be reactivated with the magnet.

4. HOMEPAGE - SLOC



Click SETUP

Note:

If the SLOC has never been configured before, step 5

(setup page 1/2) is displayed directly.

SPR-203 Initial Setup

5. SETUP 1/2:

Product:

SPR-203 (cannot be changed)

Name:

Can be changed as desired

Location:

Optionally a location can be entered



Click next to LOCATION

Note: Steps 6-7 are only displayed when clicking next to

LOCATION and can be skipped if no location is desired.

6. LOCATION 1/2:

Variant 1 (directly at the location):

Switch on GPS



Click on CURRENT LOCATION VIA GPS

Wait - GPS needs some seconds

Variant 2 (in preparation):

Enter address

exactly according to the following scheme:

address: house number, postal code, city,

country



Click on FROM LOCATION INFORMATION

wait until GPS coordinates are loaded

SPR-203 Initial Setup

7. LOCATION 2/2:

Check the address for "Current Location via

GPS"



if the address is not correct, change it

manually



Click on SAVE

8. SETUP 1/2



Click on SAVE

Table des matières

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur