Skyrc e6650 Manuel utilisateur
Version 1.0C SkyRC Technology Co., Ltd. 2010
INSTRUCTION MANUAL
- 01 -
TABLE OF CONTENTS
Introduction
Special Features
Lithium Polymer Balance Charge Program Connection Diagram
Warning and Safety Notes
Program Flow Chart
Initial Parameter Setup (Users Set Up)
Lithium (LiPo/Lilon/LiFe) program
Charging Lithium Battery in Charge Mode
Charging Lithium Battery in Balance Mode
Fast Charging of Lithium Battery
Charging Lithium Battery in the Fast Charge Mode
Storage Control of Lithium Battery
Charging Lithium Battery in the Storage Mode
Discharging of Lithium Battery
Voltage Balancing and Monitoring in the Discharge Process
Charging of NiCd/NiMH Battery
Charging NiCd/NiMH Battery in the Charge Mode
Discharge of NiCd/NiMH Battery
Charge/Discharge and Discharge/Charge Cycle of NiCd/NiMH Battery
Charging of the Pb Battery
Charging Pb (lead-acid) Battery in the Charge Mode
Discharging of the Pb Battery
Data Storage Program
Load Data Program
Various Information in the Program
Warning and Error Message
Specifications
Warranty and Service
TABLE OF CONTENTS
02
03
05
06
11
12
15
16
16
17
17
18
18
19
19
20
20
20
21
21
22
22
23
24
25
26
27
27
- 02 -
INTRODUCTION
Thank you for purchasing the e6650 LiPo Balance Charger by
SKYRC.This product is a rapid charger with a high performance
microprocessor and specialized operating software. Please read
this entire operating manual completely and attentively before
using this product, as it covers a wide range of information on
operating and safety or please do use this product in company
with a specialist!
INTRODUCTION
AC Input Power Port
(AC 100-240V, 50/60HZ)
DC Input Power Port
11-18V DC
LCD Display
(16 chr.* 1 line)
Balance
Socket
Output
Charging
Scroll Through
the Main Menu
Stop any Charge
Processes
Alter Values Cells
in Balance Charge Mode
See the Status of Individual
Resume or Start Charge Processes
Confirm an Action
Temperature
Sensor Port
Temperature
Controlled Fan
- 03 -
SPECIAL FEATURES
Optimized operating software
e6650 features the so-called AUTO function that set the feeding
current during the process of charging or discharging. Especially
for Lithium batteries, it can prevent the overcharging which may
lead to an explosion due to the user's fault. It can disconnect the
circuit automatically and alarm once detecting any malfunction.
All the programs of this product were controlled through two way
linkage and communication, to achieve the maximum safety and
minimize the trouble. All the settings can be configured by users!
SPECIAL FEATURES
Internal independent lithium battery balancer
e6650 employs an individual-cell-voltage balancer. It isn’t
necessary to connect an external balancer for balance charging.
Balancing individual cells battery discharging
During the process of discharging, e6650 can monitor and
balance each cell of the battery individually. Error message will
be indicated and the process will be ended automatically if the
voltage of any single one cell is abnormal.
Adaptable to various type of lithium battery
e6650 is adaptable to various types of Lithium batteries, such as
Li-ion, LiPo and the new LiFe series of batteries.
Fast and storage mode of lithium battery
Purposes to charge Lithium battery varies, ‘fast’ charge reduce
the duration of charging, whereas ‘store’ state can control the
final voltage of your battery, so as to store for a long time and
protect useful time of the battery.
Maximum safety
Delta-peak sensitivity: The automatic charge termination program
based on the principle of the Delta-peak voltage detection. When
the battery's voltage exceeds the threshold, the process will be
terminated automatically.
- 04 -
SPECIAL FEATURES
Automatic charging current limit
You can set up the upper limit of the charging current when
charging your NiCd or NiMH battery; it is useful for the NiMH
battery of low impedance and capacity in the 'AUTO' charging
mode.
Capacity limit
The charging capacity is always calculated as the charging
current multiplied by time. If the charging capacity exceeds the
limit, the process will be terminated automatically when you set
the maximum value.
Temperature threshold*
The battery’s internal chemical reaction will cause the temperature
of the battery to rise. If the temperature limit is reached, the
process will be terminated.
* This function is available by connecting optional temperature
probe, which is not included in our package.
Processing time limit:
You can also limit the maximum process time to avoid any
possible defect.
Input power monitoring
To protect the car battery used as DC input power from being
damaged, its voltage keeps being monitored. If it drops below
the lower limit, the process will be ended automatically.
Data store/load
The maximum five batteries’ data can be stored for users’
convenience. You can keep the data pertaining to program
setting of the battery of continuous charging or discharging.
Users can call out these data at any time without any special
program setting.
Cyclic charging/discharging
1 to 5 cyclic and continuous process of charge>discharge or
discharge>charge is operable for battery refreshing and Balancing
to stimulate the battery's activity.
- 05 -
LITHIUM POLYMER BALANCE CHARGE PROGRAM
CONNECTION DIAGRAM
This diagram shows the correct way to connect your battery to
the e6650 charger while charging in the balance charge program
mode only.
LITHIUM POLYMER BALANCE CHARGE PROGRAM
CONNECTION DIAGRAM
WARNING:
Failure to connect as shown in this diagram will damage this
charger.
The main battery leads must be connected along with the balance
lead connector as shown before charging your battery .
- 06 -
WARNING AND SAFETY NOTES
These warnings and safety notes are particularly important.
Please follow the instructions for maximum safety; otherwise the
charger and the battery can be damaged or at worst it can cause
a fire.
WARNING AND SAFETY NOTES
Never leave the charger unattended when it is connected to its
power supply. If any malfunction is found, Terminate THE
PROCESS AT ONCE and refer to the operation manual.
Keep the charger well away from dust, damp, rain, heat, direct
sunshine and vibration. Never drop it.
The allowable input voltage is 11-18V DC/110-240V AC.
This charger and the battery should be put on a heat-resistant,
noninflammable and nonconductive surface. Never place them
on a car seat, carpet or similar. Keep all the inflammable
volatile materials away from operating area.
Make sure you know the specifications of the battery to be
charged or discharged to ensure it meets the requirements of
this charger. If the program is set up incorrectly, the battery
and charger may be damaged .It can cause fire or explosion
due to overcharging. This warranty is not valid for any damage
or subsequent damage arising as a result of a misuse or failure
to observe the procedures outlined in this manual.
- 07 -
WARNING AND SAFETY NOTES
NiCd/NiMH
- Voltage level: 1.2V/cell
- Allowable fast charge current: 1C-2C (depends on the
performance of cell)
- Discharge voltage cut off level: 0.85V/cell (NiCd),
1.0V/cell(NiMH)
Li-ion
- Voltage level: 3.6V/cell
- Max. charge voltage: 4.1V/cell
- Allowable fast charge current: 1C or less
- Min. discharge voltage cut off level: 2.5V/cell or higher
LiPo
- Voltage level: 3.7V/cell
- Max. charge voltage: 4.2V/cell
- Allowable fast charge current: 1C or less
- Discharge voltage cut off level: 3.0V/cell or higher
LiFe
- Voltage level: 3.3V/cell
- Max. charge voltage: 3.6V/cell
- Allowable fast charge current: 4C or less
- Discharge voltage cut off level: 2.0V/cell or higher
Pb
- Voltage level: 2.0V/cell
- (Lead-acid) Max. charge voltage: 2.46V/cell
- Allowable fast charge current: 0.4C or less
- Discharge voltage cut off level: 1.75V/cell or higher
- 08 -
WARNING AND SAFETY NOTES
To avoid short circuit between the charge lead always connect
the charge cable to the charger first, then connect the battery.
Reverse the sequence when disconnecting.
Do not connect more than one battery pack to this charger at
any one time.
Never attempt to charge or discharge the following types of
batteries.
A battery pack which consists of different types of cells
(including different manufacturers)
Batteries that are not expressly stated by the manufacturer to
be suitable for the currents the charger carries during the
charge process.
Batteries installed in a device or which are electrically linked to
other components.
A battery fitted with an integral charge circuit or a protection
circuit.
A faulty or damaged battery.
Batteries that require a different charge technique from NiCd,
NiMh, LiPo or Gel cell (Pb, Lead acid).
Non-rechargeable batteries (Explosion hazard).
A battery that is already fully charged or just slightly discharged.
Please bear in mind the following points before commencing
charging.
Did you select the appropriate program suitable for the type of
battery you are charging?
Have you checked the battery voltage? Lithium battery packs
can be wired in parallel and in series, i.e. a 2 cell pack can be
3.7V (in parallel) or 7.4V (in series).
Did you set up adequate current for charging or discharging?
- 09 -
WARNING AND SAFETY NOTES
Have you checked that all connections are firm and secure?
Make sure there are no intermittent contacts at any point in the
circuit.
Charging
During charge process, a specific quantity of electrical energy is
fed into the battery. The charge quantity is calculated by
multiplying charge current by charge time. The maximum
permissible charge current varies depending on the battery type
or its performance, and can be found in the information by the
battery manufacturer. Only batteries that are expressly stated to
be capable of quick-charge are allowed to be charged at rates
higher than the standard charge current.
Connect the battery to the terminal of the charger: red is positive
and black is negative. Due to the difference between resistance
of cable and connector, the charger can not detect resistance of
the battery pack, the essential requirement for the charger to
work properly is that the charge lead should be of adequate
conductor cross-section, and high quality connectors which are
normally gold-plated should be fitted to both ends.
Always refer to the manual by the battery manufacturer pertaining
to charging methods, recommended charging current and
charging time. Especially, the Lithium battery should be charged
according the charging instruction provided by the manufacturer
strictly.
Attention should be paid to the connection of Lithium battery
especially.
Do not attempt to disassemble the battery pack arbitrarily.
Table des matières
Autres manuels Skyrc Chargeur
