SkyBitz CMANA00052 Manuel utilisateur

SkyBitz CMANA00052 WMS Door Sensor Install Guide Rev A 11/30/2018 1

CMANA00052 WMS Door Sensor Install Guide

WMS Kit:

WMS

WMS Bracket

2, 8-32 by 5/16 Tamper Proof Screws

6, 3/16 DIA Stainless Steel Rivets

1, Activation Magnet

1, Strike Plate with VHB

4, Strike Plate Screws

3M Primer 94 Ampoule

Tools Required:

Power Drill

3/16 Inch Drill Bit

1/8 Inch Drill Bit

Heavy Duty Blind Rivet Tool

T-15 “Pin in Torx”Tamper Resist Screw Driver

#2 Phillips Screwdriver

50/50 Isopropyl Alcohol/Water Solution

Clean Rags

WMS Door Sensor Installation Overview

This guide is for the installation of the SkyBitz

WMS Door Sensor on Dry Vans or Containers

with swing doors. The WMS will be mounted high

on the door frame of the asset and will sense the

ferrous steel of the door when it is closed. The

WMS will be mounted on the frame of the primary

door if the asset has double doors. If the door is

nonferrous, a ferrous strike plate is included in

the kit and will be mounted on the door. Once

installed, the WMS must be activated and

calibrated to ensure the sensor is functioning

properly after installation. Please contact SkyBitz

at CustomerCare@SkyBitz.com for help with any

issues you may encounter with the installation of

the SkyBitz WMS product.

Install the WMS Mounting Bracket

With the door fully closed and latched, position

the WMS Bracket as shown with the bracket

pushed against the door. Mark the upper and

lower center hole locations. Remove the bracket

and use a 3/16 inch drill bit to drill the top hole.

SkyBitz CMANA00052 WMS Door Sensor Install Guide Rev A 11/30/2018 2

With the bracket oriented as shown, install the

bracket to the door frame using one 3/16

stainless steel rivet in the top center hole. Push

the bottom of the bracket against the door and

use a 3/16 inch drill bit to match drill the lower

center hole.

Install a 3/16 inch stainless steel rivet in the lower

center hole. Match drill the remaining four WMS

bracket mounting holes.

Open the door and install the remaining four

rivets to complete the bracket installation.

SkyBitz CMANA00052 WMS Door Sensor Install Guide Rev A 11/30/2018 3

Install the WMS to the Mounting Bracket

Orient the WMS on the bracket as shown and

fasten with two 8-32 tamper resistant screws with

thread locker.

Activate the WMS

The WMS is shipped in inventory mode to prohibit

RF transmission and save battery power. The

WMS must be activated to make it operational.

Place the magnet as shown for 3 seconds and

confirm both LEDs are blinking together. This

confirms the WMS is still in inventory mode and

functioning properly.

Once the LEDs turn off after 10 seconds, hold the

magnet in the location shown again for at least 15

seconds. The LED on the left will begin to blink

RED to confirm the WMS has been activated.

SkyBitz CMANA00052 WMS Door Sensor Install Guide Rev A 11/30/2018 4

Calibrate the WMS

With the door wide open, hold the magnet in

place until the LED on the right turn’s solid blue.

Continue holding the magnet in place for at least

15 seconds until both LEDs begin an alternating

blink pattern then remove the magnet. The LEDs

will continue alternating for about 10 seconds

indicating a “Door Open” calibration reading is

about to take place.

The LEDs will begin blinking together rapidly to

signify they are taking a “Door Open” calibration

measurement. After about 10 seconds the LEDs

will return to the alternating blink pattern for 30

seconds.

During this 30 second alternating blink pattern,

close and latch the door as the WMS waits to

take a “Door Closed” calibration measurement.

The LEDs will begin blinking together rapidly to

signify the WMS is taking a “Door Closed”

calibration measurement.

SkyBitz CMANA00052 WMS Door Sensor Install Guide Rev A 11/30/2018 5

After about 10 seconds the LED on the left will

begin to blink Green to confirm a successful

calibration. If the LED on the left begins to blink

Red then the calibration has failed. Carefully

repeat the calibration procedure ensuring all the

steps are followed correctly. If the WMS still fails

calibration you will need to install a strike plate on

the door and repeat the calibration.

Install Ferrous Strike Plate

If the initial calibration has failed you will need to

install the ferrous strike plate on the door. Fully

close and latch the door. Place the edge of the

strike plate against the WMS and center it along

the side of the WMS as shown then mark the

location of the strike plate on the door. Clean the

mounting location with the 3M Primer 94 and

allow it to dry for at least 3 minutes. Remove the

film liner from the VHB tape on the back of the

strike plate and mount the strike plate to the door

in the marked location. Press firmly on the strike

plate to activate the VHB tape then pull up on the

strike to ensure a good bond has been achieved.

Repeat the calibration procedure ensuring all the

steps are followed correctly.

1) FCC Interference Statement (Part 15.105 (b))

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

2) FCC Part 15 Clause 15.21

“Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment”

SkyBitz CMANA00052 WMS Door Sensor Install Guide Rev A 11/30/2018 6

3) FCC Part 15.19(a)

“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.”

4) ISED RSS-Gen Notice:

“This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two

conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the

device.”

“Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux conditions suivantes :

1) l’appareil ne doit pas produire de brouillage;

2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.”

5) ISED Canada ICES-003 Compliance Label:

“CAN ICES-3 (B)/NMB-3(B)”

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated to provide a separation

distance of at least 20 cm from all persons.

Cet équipement est conforme aux limites d'exposition aux radiations de la FCC définies

pour un environnement non contrôlé. Cet équipement doit être installé et utilisé de

manière à assurer une distance de séparation d'au moins 20 cm de toutes les personnes.

Table des matières

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur