SKY-HERO Anakin Manuel utilisateur

GUIDE

NATURAL BORN RACER

Anakin User guide V1.0

Version

TABLE OF CONTENT

INTRODUCTION

1. SAFETY ADVICE

2. GENERAL INSTRUCTIONS AND GUIDELINES FOR USE

3. REQUIRED EQUIPMENT

PREPARE YOUR ANAKIN

1: CONNECT YOUR RX

2: INSTALL VTX ANTENNA

3: CALLIBRATION OF FLIGHT CONTROLLER & ESC’S

4: SETUP ANAKIN SETTINGS IN FLIGHT CONTROLLER



ANAKIN FRAME ADJUSTEMENTS

1. ARMS’ GEOMETRY

2. MOTORS TILT ANGLE

3. CAMERA ANGLE

4. ATTACHING PROPELLERS ON MOTORS

USING LINK9

STARTING SEQUENCE

WARRANTY TERMS

INTRODUCTION

CONGRATULATIONS on your purchase of a SKY-HERO Anakin, we hope that it will provide you with many years of fun and entertainment.

SKY-HERO products are designed and developed in Belgium (Europe), but distributed and supported across the globe through a network of dealers and

outlets that can provide assistance and advice.



SAFETY ADVICE

THIS AIRCRAFT IS NOT A TOY!











GENERAL INSTRUCTIONS AND GUIDELINES FOR USE











control.



of your control and could cause unpredictable results.





















REQUIRED EQUIPMENT

At least one Lipo 3S 1300 mAh or greater is recommended.



Basic toolset

PREPARE YOUR ANAKIN

To your RX (Receiver) PPM & S.BUS

To your RX (Receiver) - DSM

For PPM & S.BUS please use black, red, yellow and blue cable.

YELLOW: Not used

BLACK: Ground

RED: +5V

BLUE: Signal

ANAKIN FPV ARF.

If you use Sky-Hero Link 9 radio with its receiver go to page XX

Mount your receiver on the upper frame with double-sided tape.

Sky-Hero CC3D ight controller is only compable with:

• S-BUS receivers

• JR & Spektrum Satellite receivers

• PPM receivers

Please note that PWM (Pulse With Modulaon) is NOT SUPPORTED!

before

Sky Hero CC3D



Sky-Hero CC3D supports 3 kinds of receivers: PPM, S.BUS and DSM.







advantage of such a PPM signal is that only one signal wire is needed instead of all the individual wires.

For PPM

the PPM output of your receiver, no other wires need to be connected. See below:

S.BUS





For S.Bus receiver

its socket.





For JR/Spektrum/DSM satellite receiver, plug the signal wire on the satellite to the DSM port on the main board. Then swap the ORANGE and BLACK



USING LINK9 RADIO & RECEIVER



STEP 1: CONNECT YOUR RX

Then turn on your radio

CONNECT THE ANTENNA TO YOUR VTX BEFORE CONNECTING THE MAIN BATTERY









the plug and put back in reverse order.

DSM2/DSMX satellite receiver signal wire swap

How it should looks when completed.





Cut the wire to turn 25mW to 200mW or reconnect it to turn from 200mW to 25mW.

STEP 2: INSTALL TRANSMITTER (VTX) ANTENNA

CHANGE VTX POWER

Sky-Hero VTX table for your reference



STEP 3 CALLIBRATION OF FLIGHT CONTROLLER & ESC’S

This step is mandatory if you’are not using a LINK9



PLEASE NOTE THAT THE CC3D IS NOT SUPPORTED BY OPENPILOT IN RELEASES HIGHER THAN 15.02.02











Download OpenPilot Soware (VERSION 15.02.02)

Windows NSIS installer:



Mac OS X distribuon image :



Linux 32 bit Debian package :



Linux 64 bit Debian package :















On the ESC menu we have Standard ESC, Rapid ESC and OneShot ESC.

















   







diagram.

-

nue.











STEP 4: SETUP ANAKIN SETTINGS IN FLIGHT CONTROLLER

This step is mandatory if you’are not using a LINK9

Now the basic setup of CC3D is completed, you need to double check that everything is done correctly.

-



If you’ve chosen PPM receiver



-



If you’ve chosen S.Bus receiver



If you’ve chosen DSM receiver

things to check:



-





the following page, double check if the contents under “Input Channel







 

 



Make sure you fully understand the arming process and select the pre-

“Arming Sengs”



Click “Atude”





Click “Flight data”



WARNING:

PLEASE DO NOT MODIFY THESE SETTINGS UNLESS YOU

ARE FAMILIAR WITH CC3D AND KNOWS WHAT YOU ARE

DOING. SAVED MISCONFIGURE MAY CAUSE HARDWARE



ONLY BE FIXED BY PCB REPLACEMENT.

Autres manuels pour Anakin

Table des matières

Autres manuels SKY-HERO Quadricoptère

SKY-HERO

SKY-HERO Little Spyder Manuel utilisateur

SKY-HERO

SKY-HERO Anakin Manuel utilisateur

SKY-HERO

SKY-HERO ANAKIN ARF Manuel utilisateur

SKY-HERO

SKY-HERO Litle Six Manuel utilisateur

SKY-HERO

SKY-HERO Spyder Manuel utilisateur

SKY-HERO

SKY-HERO Anakin Guide d'installation

Manuels Quadricoptère populaires d'autres marques

dji

dji MAVIC 2 PRO Manuel utilisateur

Autel Robotics

Autel Robotics EVO II Dual 640T Manuel utilisateur

Carson

Carson X4 NANO Manuel utilisateur

Attop

Attop W80 Manuel utilisateur

Alias

Alias 6608 Manuel utilisateur

Reely

Reely Drone Copter 2-in-1 Manuel utilisateur

Hubsan

Hubsan FPV X4 H107D Manuel utilisateur

Falcon

Falcon S2-210 Manuel utilisateur

Kaiser Baas

Kaiser Baas KBA15007 Manuel utilisateur

Denver Electronics

Denver Electronics DCH-261 Manuel utilisateur

Craig

Craig INTERCEPTOR Manuel utilisateur

Odyssey

Odyssey TURBO RUNNER Manuel utilisateur

IMAGINARIUM

IMAGINARIUM droni stream Manuel utilisateur

Hubsan

Hubsan X4 Pro FPV Manuel utilisateur

AR.Drone

AR.Drone Parrot VSM Manuel utilisateur

Walkera

Walkera QR X900 Manuel utilisateur

dji

dji Phantom 2 Vision + Manuel utilisateur

HobbyZone

HobbyZone Zugo Manuel utilisateur