Singer MT624 Manuel utilisateur

P a g e 1 of 8, V1

SuperbaKnit interface electronic hardware exchange for MT624 & 9000

The picture below shows the Singer MT624 knitting machine.

Place the bed on a table or workbench with the right end hanging free to give access to

the bottom.

P a g e 2 of 8, V1

Remove the screw that holds the small plastic cover piece

P a g e 3 of 8, V1

Slide the cover to the right and remove it completely.

P a g e 4 of 8, V1

After removal of the plastic cover, your machine will look similar to the picture

above.

P a g e 5 of 8, V1

Remove the printed circuit board from the connector.

P a g e 6 of 8, V1

The MT 624 after removal of the PCB.

Now you have to cut the red wire that comes from somewhere under the metal belt,

and runs either to the black connector, or disappears in the cable sleeve whit the

other 4 visible wires.

P a g e 7 of 8, V1

Make sure you do not cut a second red wire that runs from the connector into the

cable sleeve. If the red wire goes to the connector, cut the red wire close to the

connector. If the red wire goes into the cable sleeve, cut the red wire where the red

wire enters the cable sleeve. This gives the maximum length for this piece of wiring.

Then enter this lose end of red wire in the clamp connector. No need to remove

insulation. Put it right in the middle and then snap together the clamp. It usually

needs no tools, just your fingers, to close the clamp.

The result should look as above.

P a g e 8 of 8, V1

Attach the connector at the end on the header in the middle of the new pc board,

and insert the pc board into the black connector. Center the contacts well and make

sure the board is inserted to its maximum position.

It should look now as above.

Now you have to adjust the 2 potentiometers that control the optical sensor

sensitivity. For instructions, please consult the “SuperbaKnit Interface A

Adjustments” document.

Place back the plastic end cover of the bed just in the reversed way as you removed

the cover, and secure the cover with the screw from the bottom side.

Ce manuel convient aux modèles suivants

1

Autres manuels Singer Machine à coudre

Singer

Singer 1669U 101 Manuel utilisateur

Singer

Singer 5102 Manuel utilisateur

Singer

Singer Sewing Machine Manuel utilisateur

Singer

Singer 211G146 Manuel utilisateur

Singer

Singer 691D100GG Manuel utilisateur

Singer

Singer 1409 Manuel utilisateur

Singer

Singer 147-115 Guide de démarrage rapide

Singer

Singer 69 Series Manuel d'installation et d'exploitation

Singer

Singer 6202; 6212 Manuel utilisateur

Singer

Singer 469U Manuel

Singer

Singer C430 Manuel utilisateur

Singer

Singer 261 Class Manuel utilisateur

Singer

Singer 301 Manuel utilisateur

Singer

Singer 1371A1 Guide de configuration

Singer

Singer WW500 Manuel utilisateur

Singer

Singer 211W155 Manuel utilisateur

Singer

Singer 247-2 Manuel utilisateur

Singer

Singer 1408 Manuel utilisateur

Singer

Singer 105-9 Manuel utilisateur

Singer

Singer 99-13 Manuel utilisateur

Singer

Singer 212W140 Manuel d'instructions

Singer

Singer 58-12 Guide de démarrage rapide

Singer

Singer Advance 7422 Manuel utilisateur

Singer

Singer 410W110 Manuel utilisateur

Manuels Machine à coudre populaires d'autres marques

Riccar

Riccar RL634DE Manuel utilisateur

Pfaff

Pfaff 3307-1 SERIES Manuel utilisateur

Janome

Janome Quilt Maker Pro 18 VERSA Manuel utilisateur

Siruba

Siruba C007JP Manuel utilisateur

Husqvarna Viking

Husqvarna Viking Designer SE Manuel utilisateur

IKEA

IKEA SY Manuel utilisateur

Pfaff

Pfaff 571 Manuel utilisateur

Brother

Brother BB370 Manuel utilisateur

Pegasus

Pegasus WT100 Series Manuel utilisateur

Reliable

Reliable 7100DB Manuel utilisateur

Pfaff

Pfaff 937 Manuel utilisateur

Pfaff

Pfaff 1471 E1 Manuel utilisateur

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuel utilisateur

HIGHLEAD

HIGHLEAD GC2008-M Manuel utilisateur

Brother

Brother BE-1204C Manuel utilisateur

JUKI

JUKI MO-104 Manuel utilisateur

Bernina

Bernina Quilting Frame Manuel utilisateur

Brother

Brother 885-V14 Manuel utilisateur