Singer 14SH654 Manuel utilisateur

SERGER MODEL 14SH654 DETAILED THREADING GUIDE

3 / 4 – Thread Sergers

Step 1:

Threading the Upper Guides:

• Make sure the thread slips under the guide

located on the top at the back of the serger.

• Insert the thread by slipping it under from right to

left.

Step 2:

Threading Upper Looper: (ORANGE)

• Always begin threading your serger by starting with

the upper (orange) looper.

• Slip the thread behind the first guide directly below the

tension dial from right to left.

• Slip the thread behind the next 4 guides (these are

indicated by orange dots below the guide).

• Next thread the eye of the looper, and then pull the

thread towards the back of the serger, leaving

approximately 8 inches of thread.

Photo #1

Step 3:

Threading Lower Looper: (YELLOW)

• Slip the thread behind the first guide directly below

the tension dial from right to left.

• Slip thread behind the 4 yellow thread guides (these

are indicated by yellow dots below the guide).

• Slip thread behind the lower looper using the

tweezers as shown in photo #2, until the thread slips

into the notch located at the far left on the looper.

• Next thread the eye of the looper, and then pull the

thread over the top of the upper (orange) looper and

then towards the back of the serger, leaving

approximately 8 inches of thread.

Lower Looper Threading Continued:

Photo #2

Photo #3

Photo #1

Step 4:

Threading the Right Needle: (GREEN)

• Slip the thread under the first guide directly below the

tension dial, and then under the guide just to the left of

the first guide.

• Run the thread over the top thread path indicated by a

green dot as shown.

• Thread through wire guide A located at the top of the

right needle and then through the eye of the needle.

• Slip thread under the overpass on the right of the foot

and then to the back of the serger, leaving

approximately 8 inches of thread.

Step 5:

Threading the Left Needle: (BLUE)

• Slip the thread under the first guide directly below the

tension dial.

• Run the thread over the bottom thread path indicated

by a blue dot as shown.

• Thread through wire guide B located at the top of the

left needle and then through the eye of the needle.

• Slip thread under the overpass on the right of the foot

and then to the back of the serger, leaving

approximately 8 inches of thread.

Step 6: Adjusting Width Adjustment Knob

It is important to set the width adjustment knob to the

correct setting, as this will affect the quality of your stitch.

Your serger is pre-set to the R setting at the factory.

• Disengage upper knife by pulling knife holder to the

right and turning the knob away from you until the

knife is in a horizontal position.

• Using Hex-Head wrench loosen width adjustment

knob by turning to the left, as shown.

• Set the knob to the desired position by moving it

right or left, and then tighten adjustment knob by

turning the Hex-Head wrench to the right.

• The edge of the width finger support plate will line up

with the guidelines on your throat plate as indicated

in the photo.

• When using left and right needle with upper and

lower looper (4-thread) set width adjustment at 4.5

guideline.

• When using left needle and upper and lower looper

(3-thread) set width adjustment at 4.5 guideline.

• When using right needle and upper and lower looper

(3-thread) set width adjustment at 3.5 guideline.

• When doing a 3-thread rolled hem set at R guideline.

Step 7: Threading Tips for the Serger

• Use good quality serger thread. This thread is sold in

larger 3000 yd. spools at most fabric and sewing retailers.

• Use the same brand of thread in all tensions, do not mix

and match brands.

• Use the same size spools on all cone adapters that are

located at the back of the machine when threading your

serger.

• Try to avoid black thread; it tends to cause static, leading

to skipped stitches. Use a dark grey or navy instead. If

you must use black, then thread-up the needles with

black, but use grey or navy in the loopers.

Autres manuels Singer Machine à coudre

Singer

Singer 147-115 Guide de démarrage rapide

Singer

Singer 7466 Manuel utilisateur

Singer

Singer 831U Manuel utilisateur

Singer

Singer 7-22 Manuel utilisateur

Singer

Singer XL-50 Manuel utilisateur

Singer

Singer 2591 series Guide de configuration

Singer

Singer 1120 Manuel utilisateur

Singer

Singer 271K Manuel utilisateur

Singer

Singer 155-1 Guide de démarrage rapide

Singer

Singer 111W112 Guide de démarrage rapide

Singer

Singer 201-2 Manuel utilisateur

Singer

Singer 14U286B Manuel utilisateur

Singer

Singer M2100 Manuel utilisateur

Singer

Singer 2273 Manuel utilisateur

Singer

Singer 5705 Manuel utilisateur

Singer

Singer Futurf II 920 Manuel utilisateur

Singer

Singer 96-41 Manuel utilisateur

Singer

Singer 7442 Manuel utilisateur

Singer

Singer 5500 Manuel utilisateur

Singer

Singer 44-81 Manuel utilisateur

Singer

Singer 145W302 Guide de configuration

Singer

Singer 140W1 Guide de démarrage rapide

Singer

Singer 14U10 Manuel

Singer

Singer 2802 - LIST OF PARTS SEWING MACHINE Manuel utilisateur

Manuels Machine à coudre populaires d'autres marques

Riccar

Riccar RL634DE Manuel utilisateur

Pfaff

Pfaff 3307-1 SERIES Manuel utilisateur

Janome

Janome Quilt Maker Pro 18 VERSA Manuel utilisateur

Siruba

Siruba C007JP Manuel utilisateur

Husqvarna Viking

Husqvarna Viking Designer SE Manuel utilisateur

IKEA

IKEA SY Manuel utilisateur

Pfaff

Pfaff 571 Manuel utilisateur

Brother

Brother BB370 Manuel utilisateur

Pegasus

Pegasus WT100 Series Manuel utilisateur

Reliable

Reliable 7100DB Manuel utilisateur

Pfaff

Pfaff 937 Manuel utilisateur

Pfaff

Pfaff 1471 E1 Manuel utilisateur

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuel utilisateur

HIGHLEAD

HIGHLEAD GC2008-M Manuel utilisateur

Brother

Brother BE-1204C Manuel utilisateur

JUKI

JUKI MO-104 Manuel utilisateur

Bernina

Bernina Quilting Frame Manuel utilisateur

Brother

Brother 885-V14 Manuel utilisateur