Simplex Ethernet Clock Manuel utilisateur
Simplex Ethernet Clock
Power Over Ethernet (POE)
Installation Manual
Installation Manual
Ethernet Clock
Power Over Ethernet (POE)
Inova Part Number: 715437
While reasonable efforts have been taken in the preparation of this
document to insure its accuracy, Simplex assumes no liability
resulting from any errors or omissions in this manual, or from the
use of the information contained herein.
© 2006 Simplex
50 Technology Drive
Westminster, MA 01441-0001Tel: 978-731-2500
http://www.simplexgrinnell.com
©2007 Simplex Time Recorder Co. All rights reserved. Page i
TABLE OF CONTENTS
Section 1 – Introduction and Network Planning........................................... 1
Section 2: System Integration .......................................................................... 2
Non-PoE Enabled Hub/Switch and Single Simplex Ethernet Clock .................3
Non-PoE-Enabled Hub/Switch and Multiple Simplex Ethernet Clocks............4
Recording Location, Static IP Address, and Host Name....................................5
Section 3: Unpacking ......................................................................................... 7
Section 4: Installation Instructions.................................................................. 8
Surface Mounting.......................................................................................................9
Pendant Mounting – Single or Double .................................................................11
Cantilever Mounting – Single or Double..............................................................13
Section 5:Installation Wrap-up and Verification.........................................15
Section 6: Telnet Command Map...................................................................16
©2007 Simplex Time Recorder Co. All rights reserved. Page ii
Section 1 – Introduction and Network Planning
Simplex PoE clocks operate with the IEEE standard for Power Over
Ethernet. The power for the clock is provided by a PoE injector or a
PoE Switch.
After you connect the clock, it will display the IP address associated
with the device.
The Simplex Ethernet clocks are linked together only in that they are
connected to the network and use the same time source. By updating
the clocks from the same time source, the clocks will remain accurate
to 200ms of that source.
There are four things that the clocks need from the network
1. A standard Ethernet connection using minimum CAT5 Cabling
minimum up to 300’ from the switch/router
2. Power over Ethernet using the IEEE 802.3AF standard (48v
DC). If the switch does not have this feature, it can be added
with single or multi port midspan injectors at the switch.
3. An IP address, fixed or provided by network DHCP service
4. SNTP (Simple Network Time Protocol) service from an internal
of external NTP server.
Section 2 contains System Integration information.
Sections 3, 4, and 5 cover the physical installation.
Section 6 contains instructions on how to configure your device using
Telnet commands.
©2007 Simplex Time Recorder Co. All rights reserved. Page 1
Section 2: System Integration
The diagrams below illustrate three options for system integration with
your PoE-capable LAN.
PoE-Enabled Hub/Switch
In the simplest example, the Ethernet is already PoE-enabled
(802.3AF) and is supporting PoE devices such as IP phones. Simply
mount the Simplex Ethernet Clock and connect it to a PoE-capable
wall jack.
©2007 Simplex Time Recorder Co. All rights reserved. Page 2
Non-PoE Enabled Hub/Switch and Single Simplex
Ethernet Clock
If the Ethernet is not currently PoE-enabled and is going to support a single
Simplex Ethernet Clock, a Single Port Midspan Power Injector must be
added to the 10/100 BaseT Ethernet LAN.
Note: The power injector must be fully compatible with IEEE 802.3af.
©2007 Simplex Time Recorder Co. All rights reserved. Page 3
Non-PoE-Enabled Hub/Switch and Multiple Simplex
Ethernet Clocks
If the Ethernet is not currently PoE-enabled and is going to support the
Simplex Ethernet Clocks, a single or multiple Port Midspan Power Injector
must be added to the 10/100 BaseT Ethernet LAN.
Note: The power injector must be fully compatible with IEEE 802.3af.
Multi-Port Midspan Power Injector
OnTime
TMClock
10/100BASE-T wall plate
Non-PoE Enabled Hub/Switch
©2007 Simplex Time Recorder Co. All rights reserved. Page 4
Recording Location, Static IP Address, and Host Name
In order to make the management of your Simplex Ethernet Clock
system as easy as possible, Simplex recommends that you record the
Clock ID, Location, IP Address, and Host Name for each unit in the
system as it is installed.
The Host Name will be visible in most DHCP servers. It should
describe the location so that the IP Address of a particular clock will
be easy to locate by matching up the Host Name. For example:
3rdFlrConfRm
Please see page 53 in the Simplex Ethernet Clock Owner’s Manual for
the procedure that can be used to change the Host Name of the
Simplex Ethernet Clock.
CLOCK
ID# LOCATION
IP ADDRESS Host Name
©2007 Simplex Time Recorder Co. All rights reserved. Page 5
CLOCK
ID# LOCATION
IP ADDRESS Host Name
©2007 Simplex Time Recorder Co. All rights reserved. Page 6
Section 3: Unpacking
The Simplex Ethernet Clock arrives fully assembled in a single
package.
Inspect all items and report any missing or damaged items using the
standard reporting process on the company web site.
Follow the directions in Section 4 for the desired mounting option.
A separate mounting kit, model ONT4KIT or ONT6KIT for cantilever or
pendant mounting, is available. Unpack the mounting kit and check its
contents against the illustration provided with the mounting kit.
(Contact your local Simplex field office in the mounting kit is missing.)
.
©2007 Simplex Time Recorder Co. All rights reserved. Page 7
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Simplex Horloge
Simplex
Simplex SIMPLEX 500 Manuel utilisateur
Simplex
Simplex 6311-1234 Manuel utilisateur
Simplex
Simplex 300 Manuel utilisateur
Simplex
Simplex EP800 Manuel utilisateur
Simplex
Simplex SIMPLEX 500 Manuel utilisateur
Simplex
Simplex Simplex Heritage Manuel d'installation
Simplex
Simplex 6311-1234 Manuel utilisateur
Simplex
Simplex Acroprint 175 Manuel d'installation
Simplex
Simplex Simplex Centennial Recorder Manuel d'installation
Simplex
Simplex 6310-9221A Manuel utilisateur
Manuels Horloge populaires d'autres marques
Silicon Laboratories
Silicon Laboratories SI5324 Manuel utilisateur
Heathkit
Heathkit GC-1005 Manuel utilisateur
Oregon Scientific
Oregon Scientific PRYSMA RMR221P Manuel utilisateur
Andrew O'Malley
Andrew O'Malley DOTKLOK Manuel utilisateur
ALGE-Timing
ALGE-Timing ASC3 Manuel utilisateur
Bodet
Bodet Profil 960 Manuel utilisateur
