IMPORTANT SAFETY INSTRUCTIONS
!
CAUTION
RISK OF ELECTROCUTION
DO NOT OPEN
Make sure not to overload the socket or any extension cord.
FortheDigiOpticalImageProcessoronlyusethepowersupply
provided or in any case a power supply approved by SIM2.
•Pay attention to the cables.
Arrange the cables so that they do not constitute an obstacle.
Also, keep them out of the reach of children.
Install the units as close as possible to the wall socket.Do not
tread on the power cables, make sure that they are not tangled
or jerked;do not expose them to heat sources;make sure they
do not form knots or bends. If the cables are damaged in any
way, stop using the system and call an authorised technician.
•Disconnect the device in the event of storms or when not
used.
To avoiddamagethatcouldbecausedbylightning strikinginthe
vicinity of your home, disconnect the units in the event of storms
or when the system is not going to be used for a long period.
•Avoid contact with liquids and exposure to humidity.
Do not use the units near water (sinks, tubs, etc.);do not place
objects containing liquids on top of or near the units and do not
exposethentorain,humidity, drops or sprays;donotusewater
or liquid detergents to clean them.
•Avoid overheating the units.
Do not block ventilation openings.Do not place the units near
heat sources such as stoves, radiators or other devices
(including amplifiers) that generate heat.Do not place the units
in a confined space (bookcase, shelves, etc.) that is not well
ventilated.
• Do not expose eyes to the intense light of the lamp.
Neverlook directly into the lamp throughtheventilationopening
when it is working.
Thiscoulddamageyoureyesight.Inthis respect, payparticular
attention to children.
•Position the unit on a stable surface.
To avoid serious injury and damage to things, make sure the
units are placed on a level, flat and stable surface from which
they cannot fall, tip over or slide.In this respect, pay particular
attention when they are placed on a trolley to be moved.Do not
to expose them to shocks.
•Do not put anything in the openings of the units.
Make sure that no object is placed inside the units. If this
happens,immediately disconnecttheunitfromthe powersupply
and call an authorised technician.
This symbol indicates the danger of possible electric
shock caused by uninsulated current inside the
product.
This symbol indicates the presence of important
instructions regarding use and maintenance of the
product.
•Read and keep this manual.
This manual contains important information on how to install
and use this device in an appropriate manner. Before use,
carefullyreadthesafetyrulesandinstructions.Keepthemanual
for all future reference.
•Avoid contact with the internal parts of the units.
Inside the units there are electrical parts fed with dangerous
voltage and parts that operate at high temperatures. Do not
opentheunits;contactauthorised personnel forall maintenance
and repair operations.
Opening the units will also invalidate the warranty.
•Device for disconnecting the power supply.
The device for disconnecting the units from the electrical grid
is the feed cable plug. During installation make sure that the
feed cable plugs and the electrical system sockets are easily
accessible. To disconnect the units from the electric sockets,
pull the plug and not the cable.
•Only use the type of feed indicated.
Connect the units to an electrical grid with nominal voltage
between the values of 100-240 VAC, 50/60 Hz and provided
with grounding.If you are not sure of the type of power in your
home, consult a qualified technician.
TheRTXsystemconsistsoftwoparts,theDigiOpticalImage
Processor and the Display, connected by an optical fibre
cable.Below, the unit will be referred to as including the two
parts making up the system.
•Federal Communication Commission (FCC Statement)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is used in a
commercial environment.This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determinated by
turning the equipment off and on, the user is encuraged to try
to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna
-Increasetheseparationbetweentheequipmentandreceiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
•For customers in Canada
This Class B digital apparatus complies with Canadian ICES-
003.
•For customers in the United Kingdom
ATTENTION:This apparatus must be earthed.
The wires in this mains lead are coloured in accordance with
the following code:
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
Thewirewhichis colouredgreen-and-yellow mustbeconnected
to the terminal in the plug which is marked by the letter
E or by the safety earth symbol or coloured green or green-
and-yellow.
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
