SILENT KNIGHT SK-5208 Manuel utilisateur

Installation and

Operations Manual

Fire Control/

Part Number 151204 Rev L

Communicator

MODEL SK-5208

151286 -1

Installation Procedure

Adherence to the following will aid in problem-free installation with long-term reliability:

Installation Precautions - Adherence to the following will aid in problem-free installation

with long-term reliability: WARNING - Several different sources of power can be connected

to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit

and associated equipment may be damaged by removing and/or inserting cards, modules, or

interconnecting cables while the unit is energized. Do not attempt to install, service, or operate

this unit until manuals are read and understood. CAUTION - System Re-acceptance Test after

Software Changes: To ensure proper system operation, this product must be tested in

accordance with NFPA 72 after any programming operation or change in site-specific

software. Re-acceptance testing is required after any change, addition or deletion of system

components, or after any modification, repair or adjustment to system hardware or wiring. All

components, circuits, system operations, or software functions known to be affected by a

change must be 100% tested. In addition, to ensure that other operations are not inadvertently

affected, at least 10% of initiating devices that are not directly affected by the change, up to a

maximum of 50 devices, must also be tested and proper system operation verified. This

system meets NFPA requirements for operation within the range of 0°C-49°C (32°F-120°F) or

humidity within the range of 10%-93% at 30°C (86°F) noncondensing. However, the useful

life of the system's standby batteries and the electronic components may be adversely affected

by extreme temperature ranges and humidity. Therefore, it is recommended that this system

and its peripherals be installed in an environment with a normal room temperature of 15-27º

C/60-80º F. Verify that wire sizes are adequate for all initiating and indicating device loops.

Most devices cannot tolerate more than a 10% I.R. drop from the specified device voltage.

Like all solid state electronic devices, this system may operate erratically or can be damaged

when subjected to lightning induced transients. Although no system is completely immune

from lightning transients and interference, proper grounding will reduce susceptibility.

Overhead or outside aerial wiring is not recommended, due to an increased susceptibility to

nearby lightning strikes. Consult with the Technical Services Department if any problems are

anticipated or encountered. Disconnect AC power and batteries prior to removing or

inserting circuit boards. Failure to do so can damage circuits. Remove all electronic

assemblies prior to any drilling, filing, reaming, or punching of the enclosure. When possible,

make all cable entries from the sides or rear. Before making modifications, verify that they

will not interfere with battery, transformer, or printed circuit board location. Do not tighten

screw terminals more than 9 in-lbs. Over-tightening may damage threads, resulting in

reduced terminal contact pressure and difficulty with screw terminal removal. Silent Knight

fire alarm control panels contain static-sensitive components. Always ground yourself with a

proper wrist strap before handling any circuits so that static charges are removed from the

body. Use static suppressive packaging to protect electronic assemblies removed from the

unit.

Follow the instructions in the installation, operating, and programming manuals. These

instructions must be followed to avoid damage to the control panel and associated equipment.

VIP-Series Voice Integration Package Installation/Operation Manual

-2 151286

FACP operation and reliability depend upon proper installation.

While installing a fire alarm system may make lower insurance rates possible, it is not a

substitute for fire insurance! An automatic fire alarm system - typically made up of smoke

detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm

control with remote notification capability - can provide early warning of a developing fire.

Such a system, however, does not assure protection against property damage or loss of life

resulting from a fire. Any fire alarm system may fail for a variety of reasons: Smoke

detectors may not sense fire where smoke cannot reach the detectors such as in chimneys, in

walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire

on another level or floor of a building. A second floor detector, for example, may not sense a

first floor or basement fire. Furthermore, all types of smoke detectors, including ionization

and photoelectric types, have sensing limitations. No type of smoke detector can sense every

kind of fire caused by carelessness and safety hazards like smoking in bed, violent explosions,

escaping gas, improper storage of flammable materials, overloaded electrical circuits, children

playing with matches, or arson.

IMPORTANT! Smoke detectors must be installed in the same room as the control panel and

in rooms used by the system for the connection of alarm transmission wiring,

communications, signaling, and/or power. If detectors are not so located, a developing fire

may damage the alarm system, crippling its ability to report a fire. Audible warning devices

such as bells may not alert people if these devices are located on the other side of closed or

partly open doors or are located on another floor of a building. A fire alarm system will not

operate without any electrical power. If AC power fails, the system will operate from standby

batteries only for a specified time. Rate-of-Rise heat detectors may be subject to reduced

sensitivity over time. For this reason, the rate-of-rise feature of each detector should be tested

at least once per year by a qualified fire protection specialist. Equipment used in the system

may not be technically compatible with the control. It is essential to use only equipment listed

for service with your control panel. Telephone lines needed to transmit alarm signals from a

premise to a central monitoring station may be out of service or temporarily disabled. The

most common cause of fire alarm malfunctions, however, is inadequate maintenance. All

devices and system wiring should be tested and maintained by professional fire alarm

installers following written procedures supplied with each device. System inspection and

testing should be scheduled monthly or as required by National and/or local fire codes.

Adequate written records of all inspections should be kept.

Contents

Section 1

Introduction .............................................................................................................................................. 1-1

1.1 Model SK-5208 Features ......................................................................................................................... 1-1

1.2 About This Manual .................................................................................................................................. 1-2

1.2.1 Optional Accessories ...................................................................................................................... 1-2

Limitations of Fire Alarm Systems ........................................................................................ 1-3

Section 2

Agency Listings and Requirements ........................................................................ 2-1

2.1 Federal Communications Commission (FCC) ......................................................................................... 2-1

2.2 Underwriters Laboratories (UL) .............................................................................................................. 2-2

2.2.1 Requirements for All Installations .................................................................................................... 2-2

Restricted Options: ................................................................................................................. 2-2

2.2.2 Requirements for Central Station Fire Alarm Systems .................................................................... 2-2

2.2.3 Requirements for Auxiliary Protected Fire Alarm Systems for Fire Alarm Service ........................2-2

2.2.4 Requirements for Remote Station Protected Fire Alarm Systems, for Digital Communication or

Polarity Reversal 2-2

Section 3

Control Panel Installation ...................................................................................................... 3-1

3.1 Electrical Specifications ........................................................................................................................... 3-1

3.2 Environmental Specifications .................................................................................................................. 3-1

3.3 Wiring Specifications ............................................................................................................................... 3-2

3.4 Control Board Components ..................................................................................................................... 3-3

3.5 Mounting the SK-5208 ............................................................................................................................. 3-5

3.5.1 Preventing Water Damage ................................................................................................................ 3-5

3.6 Current Draw Calculations ....................................................................................................................... 3-6

3.6.1 Worksheet Requirements .................................................................................................................. 3-6

Filling in the Current Draw Worksheet, Table 3-2 (Section 3.6.2) ....................................... 3-6

3.6.2 Current Draw Worksheet .................................................................................................................. 3-6

3.6.3 Maximum Battery Standby Load ...................................................................................................... 3-8

3.7 AC Wiring ................................................................................................................................................ 3-9

3.8 Backup Batteries .................................................................................................................................... 3-10

3.9 Terminal Strip Description ..................................................................................................................... 3-11

3.10 Telephone Line Connection .................................................................................................................. 3-13

3.11 Detector Installation ............................................................................................................................... 3-14

3.11.1 Class A (Style D) Zones ................................................................................................................. 3-14

3.11.2 Class B (Style B) Zones ................................................................................................................. 3-15

3.11.3 Four-Wire Smoke Detector Connection ......................................................................................... 3-16

3.11.4 Two-Wire Smoke Detector Connection ......................................................................................... 3-17

3.12 Supervised Notification Appliance Outputs ......................................................................................... 3-18

3.13 Auxiliary Relays .................................................................................................................................... 3-19

Contents

3.14 Accessory Devices ................................................................................................................................. 3-20

3.14.1 Setting ID Codes ............................................................................................................................. 3-20

3.14.2 Model SK-5235 Remote Annunciator ............................................................................................ 3-21

3.14.2.1 Mounting the SK-5235 Remote Annunciator ...................................................................... 3-21

3.14.2.2 Wiring the SK-5235 ............................................................................................................. 3-22

3.14.3 Model SK-5280 Status Display Module ......................................................................................... 3-23

3.14.3.1 Mounting the SK-5280 ......................................................................................................... 3-25

Mounting the SK-5280 into SK-5208 Cabinet .................................................................... 3-25

Mounting the SK-5280 into the SK-2190 Accessory Cabinet. ............................................ 3-26

3.14.3.2 Wiring Relays ...................................................................................................................... 3-27

3.14.3.3 Wiring LEDs to Outputs ...................................................................................................... 3-27

3.14.4 Model SK-5217 Zone Expander Installation .................................................................................. 3-28

3.14.4.1 Zone Inputs .......................................................................................................................... 3-29

3.14.4.2 Mounting Instructions .......................................................................................................... 3-30

Mounting the SK-5217 into SK-5208 Cabinet .................................................................... 3-30

Mounting the SK-5217 into the SK-2190 Accessory Cabinet. ............................................ 3-31

3.14.5 Model 5824 Installation Instructions .............................................................................................. 3-32

3.14.5.1 Mounting the 5824 Module .................................................................................................. 3-32

3.14.5.2 5824 SBUS Connections ...................................................................................................... 3-33

3.15 Special Applications .............................................................................................................................. 3-34

3.15.1 Model 5220 Direct Connect Module .............................................................................................. 3-34

3.15.1.1 City Box Connection ............................................................................................................ 3-34

3.15.1.2 NFPA 72 Polarity Reversal .................................................................................................. 3-35

3.15.2 Keltron 95M3158 Tones Transmitter Module ................................................................................ 3-36

3.15.3 Using a MR-201/T Control Relay From Air Products ................................................................... 3-37

Section 4

Programming ......................................................................................................................................... 4-1

4.1 Keypad Operation During Programming ................................................................................................. 4-1

4.1.1 Special Characters ............................................................................................................................. 4-2

4.1.2 Enabling Extended Programming List .............................................................................................. 4-2

4.2 Programming Flow .................................................................................................................................. 4-3

4.2.1 Zone Options ..................................................................................................................................... 4-4

4.2.2 Misc System Option .......................................................................................................................... 4-5

4.2.3 NAC Cadence ................................................................................................................................... 4-6

4.2.3.1 Cadence Patterns .................................................................................................................... 4-6

4.2.4 NAC Options .................................................................................................................................... 4-7

4.2.5 Relay Options ................................................................................................................................... 4-8

4.2.6 User Code ......................................................................................................................................... 4-9

4.2.7 Account ........................................................................................................................................... 4-10

4.2.8 Computer Options ........................................................................................................................... 4-11

4.2.8.1 Computer Code .................................................................................................................... 4-11

4.2.9 Line Options ................................................................................................................................... 4-12

4.2.10 Misc Reporting ............................................................................................................................... 4-13

4.2.11 5280 Outputs ................................................................................................................................... 4-14

4.2.12 5824 Expander Options .................................................................................................................. 4-15

4.2.13 DST/Clk Options ............................................................................................................................ 4-16

4.3 Programming Options ............................................................................................................................ 4-17

Contents

iii

Section 5

Operation ..................................................................................................................................................... 5-1

5.1 Installer & User Keys ............................................................................................................................... 5-1

5.2 On-board Touchpad and SK-5235 Operation .......................................................................................... 5-2

5.2.1 View Control Panel Firmware Number and Revision ...................................................................... 5-3

5.3 Acknowledge Operation .......................................................................................................................... 5-3

5.4 LED Indicators ......................................................................................................................................... 5-4

5.5 Releasing Operation ................................................................................................................................. 5-5

5.5.1 Cross Alarm Operation ..................................................................................................................... 5-5

5.5.1.1 Default NAC Settings for Releasing ......................................................................................5-5

5.5.2 Double Interlock Releasing Operation ............................................................................................. 5-7

5.6 Smoke Alarm Verification ....................................................................................................................... 5-8

5.7 System Testing ......................................................................................................................................... 5-9

5.7.1 Fire Drills .......................................................................................................................................... 5-9

5.7.2 Walk Test .......................................................................................................................................... 5-9

5.7.3 Automatic Self Test .......................................................................................................................... 5-9

5.7.4 Watchdog Circuit .............................................................................................................................. 5-9

5.8 Communicating with a Programming Computer ...................................................................................5-10

5.8.1 Programming From a Remote Computer Location ........................................................................ 5-10

5.8.1.1 Having the Control Panel Call the Remote Computer ......................................................... 5-10

5.8.1.2 Having Remote Computer Call the Control Panel ............................................................... 5-11

5.8.2 Directly Connecting to a Programming Computer ......................................................................... 5-12

Section 6

Reporting ..................................................................................................................................................... 6-1

6.1 Reporting Formats .................................................................................................................................... 6-1

6.2 Reporting Codes ....................................................................................................................................... 6-2

6.2.1 Default Settings for 3/1 Format ........................................................................................................ 6-4

Section 7

Troubleshooting ................................................................................................................................7-1

7.1 System Error Messages ............................................................................................................................ 7-1

7.2 Earth Ground Fault Troubleshooting ....................................................................................................... 7-3

7.3 Earth Fault Resistance .............................................................................................................................. 7-4

Appendix A

Compatible Devices ..................................................................................................................... A-1

A.1 Notification Appliances .......................................................................................................................... A-1

A.2 Two-Wire Smoke Detectors .................................................................................................................. A-11

A.3 Four Wire Smoke Detectors .................................................................................................................. A-13

Silent Knight Fire Product Warranty and Return Policy

SK-5208 Plus Basic Operating Instructions P/N 151214 Rev. A

Installation Manual

P/N 151204 1-1

Section 1

Introduction

The Model SK-5208 is an 24-volt 10-zone fire alarm control panel (expandable up to 30 zones

using SK-5217 Zone Expanders) with a digital communicator that meets NFPA 72

requirements. The SK-5208 cabinet can be surface mounted or semi-flush mounted.

1.1 Model SK-5208 Features

• Built-in two-line (16 Character each line) LCD display provides easy to read english

language readouts

• 10 Initiation inputs, 8 Class B (Style B) and 2 zones that can be configured as Class B

(Style B) or Class A (Style D), expandable to 30 zones

• Supervised zone expanders and I/O modules can be mounted remotely from the main

control panel

• UL Listed

• Event History Buffer (approximately 150 events) with Date/Time stamp

• All zones are compatible with 2- and 4-wire detectors

• 8 selectable/programmable output pattern for notification appliance circuits (Including

ANSI 3.41)

• Built-in Digital Alarm Communicator Transmitter (DACT)

• 4 Notification appliance circuits

• 4 programmable general purpose relays

• Programmable smoke verification, pre-alarm delay, cross zoning and enhanced

verification mode features that can help minimize false alarms

• Capable of single or dual operation for water releasing services.

• Programmable from the built-in control panel touchpad, remote annunciator or Window®

downloading software

• Built-in walk test

Model SK-5208 Fire Control/Communicator Installation and Operation Manual

1-2 P/N 151204

1.2 About This Manual

The Model SK-5208 Fire Control/Communicator Installation Manual (P/N 151204) is

intended for those persons involved with the installation and maintenance of the SK-5208

panel. It is a comprehensive guide, providing detailed instructions, and should be kept for

reference. As much as possible, we have tried to organize the manual chronologically by the

tasks that need to be performed.

1.2.1 Optional Accessories

Table 1-1: Standards Used in this Manual

A same graphic replicating the key that you press on a touchpad.

LCD DISPLAY MESSAGE The font shown to the left represents messages that you see on a liquid crystal

display (LCD) on the control panel and the remote annunciator.

1-1, 2-3, etc. This manual is organized into sections. Section numbers are part of the page

numbers. For example, 1-1 means Page 1 of Section 1.

Table 1-2: Compatible Modules Manufactured by Silent Knight

Model What It Does

SK-5217 Zone Expander Adds 10 zones to the SK-5208 for a total expansion of the system to 30 zones.

SK-2190 Accessory Cabinet Used for remote mounting of the SK-5217 Zone Expander.

Dimensions: 10-3/8”W x 10-3/16”H x 3”D (26.35 cm W x 25.88 cm H x 7.62 cm D)

5220 Direct Connect Module For direct alarming and trouble transmission from the SK-5208 to a supervising

station.

SK-5235 Remote Annunciator For remote annunciation, operation, and on-site programming.

SK-5280 The Model SK-5280 Status Display module provides outputs and control functions for

remote annunciation of alarm, trouble, and supervisories for each zone.

5824 Provides connectivity to a Serial or Parallel printer. (See Section 4.2.12 for

programming.)

SK-5499 Signal Power Expander Notification circuit power for additional notification appliances. Provides additional

9A of 24 VDC, supervised.

SK-5495 Signal Power Expander Notification circuit power for additional notification appliances. Provides additional

6A of 24 VDC, supervised.

SKSS Downloading Software

Model 5660 For remote programming of the SK-5208 using a personal computer.

PLEX-2 Optional door accessory for single button operation. (See Section 4.3 for

programming.)

Table des matières

Autres manuels SILENT KNIGHT Contrôleurs

SILENT KNIGHT

SILENT KNIGHT SK-Control Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur