SILENT KNIGHT INTELLIKNIGHT 5808 Manuel utilisateur

Installation and

Operations Manual

INTELLIKNIGHT

MODEL 5808

Part Number 151274 Rev K

Addressable Fire Control Panel

Installation Procedure

Adherence to the following will aid in problem-free installation with long-term reliability:

Installation Precautions - Adherence to the following will aid in problem-free installation

with long-term reliability: WARNING - Several different sources of power can be connected

to the fire alarm control panel. Disconnect all sources of power before servicing. Control unit

and associated equipment may be damaged by removing and/or inserting cards, modules, or

interconnecting cables while the unit is energized. Do not attempt to install, service, or operate

this unit until manuals are read and understood. CAUTION - System Re-acceptance Test after

Software Changes: To ensure proper system operation, this product must be tested in

accordance with NFPA 72 after any programming operation or change in site-specific

software. Re-acceptance testing is required after any change, addition or deletion of system

components, or after any modification, repair or adjustment to system hardware or wiring. All

components, circuits, system operations, or software functions known to be affected by a

change must be 100% tested. In addition, to ensure that other operations are not inadvertently

affected, at least 10% of initiating devices that are not directly affected by the change, up to a

maximum of 50 devices, must also be tested and proper system operation verified. This

system meets NFPA requirements for operation within the range of 0°C-49°C (32°F-120°F) or

humidity within the range of 10%-93% at 30°C (86°F) noncondensing. However, the useful

life of the system's standby batteries and the electronic components may be adversely affected

by extreme temperature ranges and humidity. Therefore, it is recommended that this system

and its peripherals be installed in an environment with a normal room temperature of 15-27º

C/60-80º F. Verify that wire sizes are adequate for all initiating and indicating device loops.

Most devices cannot tolerate more than a 10% I.R. drop from the specified device voltage.

Like all solid state electronic devices, this system may operate erratically or can be damaged

when subjected to lightning induced transients. Although no system is completely immune

from lightning transients and interference, proper grounding will reduce susceptibility.

Overhead or outside aerial wiring is not recommended, due to an increased susceptibility to

nearby lightning strikes. Consult with the Technical Services Department if any problems are

anticipated or encountered. Disconnect AC power and batteries prior to removing or

inserting circuit boards. Failure to do so can damage circuits. Remove all electronic

assemblies prior to any drilling, filing, reaming, or punching of the enclosure. When possible,

make all cable entries from the sides or rear. Before making modifications, verify that they

will not interfere with battery, transformer, or printed circuit board location. Do not tighten

screw terminals more than 9 in-lbs. Over-tightening may damage threads, resulting in

reduced terminal contact pressure and difficulty with screw terminal removal. Silent Knight

fire alarm control panels contain static-sensitive components. Always ground yourself with a

proper wrist strap before handling any circuits so that static charges are removed from the

body. Use static suppressive packaging to protect electronic assemblies removed from the

unit.

Follow the instructions in the installation, operating, and programming manuals. These

instructions must be followed to avoid damage to the control panel and associated equipment.

FACP operation and reliability depend upon proper installation.

While installing a fire alarm system may make lower insurance rates possible, it is not a

substitute for fire insurance! An automatic fire alarm system - typically made up of smoke

detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm

control with remote notification capability - can provide early warning of a developing fire.

Such a system, however, does not assure protection against property damage or loss of life

resulting from a fire. Any fire alarm system may fail for a variety of reasons: Smoke

detectors may not sense fire where smoke cannot reach the detectors such as in chimneys, in

walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire

on another level or floor of a building. A second floor detector, for example, may not sense a

first floor or basement fire. Furthermore, all types of smoke detectors, including ionization

and photoelectric types, have sensing limitations. No type of smoke detector can sense every

kind of fire caused by carelessness and safety hazards like smoking in bed, violent explosions,

escaping gas, improper storage of flammable materials, overloaded electrical circuits, children

playing with matches, or arson.

IMPORTANT! Smoke detectors must be installed in the same room as the control panel

and in rooms used by the system for the connection of alarm transmission wiring,

communications, signaling, and/or power. If detectors are not so located, a developing fire

may damage the alarm system, crippling its ability to report a fire. Audible warning devices

such as bells may not alert people if these devices are located on the other side of closed or

partly open doors or are located on another floor of a building. A fire alarm system will not

operate without any electrical power. If AC power fails, the system will operate from standby

batteries only for a specified time. Rate-of-Rise heat detectors may be subject to reduced

sensitivity over time. For this reason, the rate-of-rise feature of each detector should be tested

at least once per year by a qualified fire protection specialist. Equipment used in the system

may not be technically compatible with the control. It is essential to use only equipment listed

for service with your control panel. Telephone lines needed to transmit alarm signals from a

premise to a central monitoring station may be out of service or temporarily disabled. The

most common cause of fire alarm malfunctions, however, is inadequate maintenance. All

devices and system wiring should be tested and maintained by professional fire alarm

installers following written procedures supplied with each device. System inspection and

testing should be scheduled monthly or as required by National and/or local fire codes.

Adequate written records of all inspections should be kept.

151274 i

Contents

Section 1

Introduction .............................................................................................................................................. 1-1

1.1 Overview of Basic System ....................................................................................................................... 1-1

1.1.1 Hardware Features ............................................................................................................................ 1-1

1.1.2 Software Features ............................................................................................................................. 1-2

1.2 About this Manual .................................................................................................................................... 1-2

1.2.1 Terms Used in this Manual ............................................................................................................... 1-2

1.3 Compatible Products ................................................................................................................................ 1-3

1.4 How to Contact Silent Knight .................................................................................................................. 1-4

Limitations of Fire Alarm Systems ........................................................................................ 1-5

Requirements and recommendations for proper use of fire alarm systems including smoke

detectors and other fire alarm devices: .................................................................................. 1-7

Section 2

Agency Listings, Approvals, and Requirements ................................... 2-1

2.1 Federal Communications Commission (FCC) ......................................................................................... 2-1

2.2 Underwriters Laboratories (UL) .............................................................................................................. 2-3

2.2.1 Requirements for All Installations .................................................................................................... 2-3

Restricted Options: ................................................................................................................. 2-3

2.2.2 Requirements for Central Station Fire Alarm Systems .................................................................... 2-3

2.2.3 Requirements for Local Protected Fire Alarm Systems ................................................................... 2-4

2.2.4 Requirements for Remote Station Protected Fire Alarm Systems .................................................... 2-4

2.2.5 Requirements for Auxiliary Protected Fire Alarm Systems for Fire Alarm Service ........................ 2-4

Section 3

Before You Begin Installing ............................................................................................... 3-1

3.1 What’s in the Box? ................................................................................................................................... 3-1

3.2 Environmental Specifications .................................................................................................................. 3-1

3.3 Electrical Specifications ........................................................................................................................... 3-2

3.4 Wiring Specifications ............................................................................................................................... 3-3

3.5 Board Assembly Diagram ..................................................................................................................... 3-4

3.6 Calculating Current Draw and Standby Battery ...................................................................................... 3-5

3.6.1 Current Draw Worksheet Requirements ........................................................................................... 3-5

3.6.1.1 Current Draw Worksheet for SLC Devices ........................................................................... 3-6

3.6.1.2 Maximum Battery Standby Load ........................................................................................... 3-8

IntelliKnight 5808 Installation Manual

ii 151274

Section 4

Control Panel Installation ...................................................................................................... 4-1

4.1 Mounting the Control Panel Cabinet ....................................................................................................... 4-1

4.1.1 Preventing Water Damage ................................................................................................................ 4-1

4.1.2 Removing the 5808 Assembly from the Housing ............................................................................. 4-1

4.2 AC Connection ......................................................................................................................................... 4-2

4.3 Battery Connection .................................................................................................................................. 4-3

4.3.1 RBB Accessory Cabinet ................................................................................................................... 4-4

4.3.1.1 Installing the RBB Accessory Cabinet and Batteries ............................................................. 4-4

4.4 SBUS Wiring ........................................................................................................................................... 4-6

4.4.1 Calculating Wiring distance for SBUS modules ..............................................................................4-6

Wiring Distance calculation example: ................................................................................... 4-8

4.4.2 Wiring Configurations ...................................................................................................................... 4-8

4.5 5860 Remote Annunciator Installation .................................................................................................... 4-9

4.5.1 Mounting the 5860 .......................................................................................................................... 4-10

4.5.1.1 Flush Mounting .................................................................................................................... 4-11

Flush Mounting with an Electrical Box ............................................................................... 4-12

Flush Mounting Steps .......................................................................................................... 4-12

4.5.1.2 Surface Mounting ................................................................................................................. 4-13

4.5.2 Connecting the 5860 to the Panel ................................................................................................... 4-14

4.6 5824 Serial/Parallel Printer Interface Module Installation .................................................................... 4-14

4.6.1 Selecting 5824 Options ................................................................................................................... 4-16

Printer and Output Port Options ........................................................................................... 4-16

4.7 5880 LED I/O Module ........................................................................................................................... 4-17

4.7.1 5880 Board Layout ......................................................................................................................... 4-17

4.7.2 FACP Connection ........................................................................................................................... 4-18

4.7.3 LED Wiring .................................................................................................................................... 4-19

4.7.4 Dry Contact Wiring ........................................................................................................................ 4-20

4.8 5865-3 / 5865-4 LED Annunciator Installation ..................................................................................... 4-21

4.8.1 FACP Connection ........................................................................................................................... 4-21

4.8.2 5865 Mounting ................................................................................................................................ 4-22

4.9 Configuring Modules ............................................................................................................................. 4-23

4.9.1 Assigning Module IDs .................................................................................................................... 4-23

4.10 Telephone Connection ........................................................................................................................... 4-24

4.11 5211 Ground Start Relay ........................................................................................................................ 4-24

4.12 Notification Appliance/Auxiliary Power Circuits .................................................................................. 4-24

4.12.1 Conventional Notification Appliance ............................................................................................. 4-25

4.12.1.1 Class B Notification Wiring ................................................................................................. 4-25

4.12.1.2 Class A Notification Wiring ................................................................................................ 4-26

4.12.2 Auxiliary Power Installation ........................................................................................................... 4-27

4.12.2.1 Door Holder Power .............................................................................................................. 4-27

4.12.2.2 Constant Power .................................................................................................................... 4-28

4.12.2.3 Resettable Power .................................................................................................................. 4-28

4.13 On-Board Programmable Relays (Conventional) .................................................................................. 4-28

4.13.1 Trouble Relay ................................................................................................................................. 4-28

4.13.2 Programmable Relays ..................................................................................................................... 4-28

4.14 Remote Station Applications ................................................................................................................. 4-29

4.14.1 Keltron Model 3158 Installation ..................................................................................................... 4-29

4.14.2 City Box Connection Using the 5220 Module ................................................................................4-30

4.14.3 NFPA 72 Polarity Reversal ............................................................................................................. 4-31

4.14.3.1 Using the 5220 Module ........................................................................................................ 4-31

4.14.3.2 Using the 7644 Module ........................................................................................................ 4-33

4.14.4 Using the SD500-ARM Addressable Relay Module ...................................................................... 4-34

4.14.5 Using a MR-201/T Control Relay From Air Products ................................................................... 4-35

Contents

151274 iii

4.14.6 Transmitter Activated by Dry Contacts .......................................................................................... 4-36

Section 5

SLC Device Installation ............................................................................................................ 5-1

5.1 List of SLC Devices ................................................................................................................................. 5-1

5.2 Maximum Number of Devices ................................................................................................................. 5-2

5.3 Wiring Requirements for SLC Devices ................................................................................................... 5-2

5.3.1 Wiring 5815XL in Style 4 (Class B) Configuration ......................................................................... 5-2

5.3.2 Wiring 5815XL in Style 6 & 7 (Class A) Configuration .................................................................. 5-4

5.4 Wiring Detectors ...................................................................................................................................... 5-5

5.5 Addressing Devices .................................................................................................................................. 5-6

5.5.1 SD505-APS, SD505-AHS, & SD505-AIS ...................................................................................... 5-6

5.5.2 SLC Devices with Dip Switches ....................................................................................................... 5-7

Section 6

Programming Overview ........................................................................................................... 6-1

6.1 JumpStart Autoprogramming ................................................................................................................... 6-1

6.1.1 Input Points ....................................................................................................................................... 6-2

6.1.2 Output Points .................................................................................................................................... 6-2

6.1.3 Running JumpStart ........................................................................................................................... 6-2

6.2 Mapping Overview .................................................................................................................................. 6-4

6.2.1 Input Point Mapping ......................................................................................................................... 6-5

6.2.2 Output Circuit Mapping .................................................................................................................... 6-6

6.2.3 Zone Event Mapping ........................................................................................................................ 6-7

6.2.4 Mapping LED Points ........................................................................................................................ 6-9

6.3 Programming Using the 5660 Silent Knight Software Suite ................................................................. 6-10

6.4 Programming Using an Annunciator ..................................................................................................... 6-10

6.4.1 Entering / Exiting the Programming Menu ..................................................................................... 6-11

6.4.2 Moving through the Menus ............................................................................................................. 6-11

6.4.3 Selecting Options and Entering Data .............................................................................................. 6-12

6.4.4 Editing Keys ................................................................................................................................... 6-12

6.5 Programming Menu Quick Reference ................................................................................................... 6-13

Section 7

Programming ......................................................................................................................................... 7-1

7.1 UL 864 Programming Requirements ....................................................................................................... 7-1

7.2 Modules .................................................................................................................................................... 7-1

7.2.1 Edit Modules ..................................................................................................................................... 7-2

7.2.1.1 Naming Modules .................................................................................................................... 7-2

7.2.1.2 Module, Wiring Class ............................................................................................................ 7-3

7.2.2 Adding a Module .............................................................................................................................. 7-3

7.2.3 Deleting a Module ............................................................................................................................ 7-3

7.3 Zone ......................................................................................................................................................... 7-4

IntelliKnight 5808 Installation Manual

iv 151274

7.3.1 Edit Zone ........................................................................................................................................... 7-4

7.3.1.1 Edit Zone Name ..................................................................................................................... 7-4

7.3.1.2 Edit Zone Properties ............................................................................................................... 7-5

Alarm Delay Characteristics .................................................................................................. 7-6

Heat Temperature Setting ...................................................................................................... 7-7

7.3.1.3 Zone Outputs .......................................................................................................................... 7-8

Mapping to Zone Events ........................................................................................................ 7-8

Zone Mapping Example ......................................................................................................... 7-9

7.3.1.4 Cadence Patterns .................................................................................................................. 7-10

7.3.1.5 Zone Accessory Options ...................................................................................................... 7-10

7.3.2 Add Zone ........................................................................................................................................ 7-11

7.3.3 Delete Zone ..................................................................................................................................... 7-11

7.3.4 View Zone Points ............................................................................................................................ 7-12

7.4 Group ..................................................................................................................................................... 7-13

7.4.1 Edit Group ....................................................................................................................................... 7-13

7.4.1.1 Edit Group Name ................................................................................................................. 7-13

7.4.1.2 Edit Group Properties ........................................................................................................... 7-14

Latching / Non-latching Outputs .......................................................................................... 7-14

Silencing Options ................................................................................................................. 7-15

Response with System-Wide Conditions ............................................................................. 7-15

7.4.2 Add Group ...................................................................................................................................... 7-16

7.4.3 Delete Group ................................................................................................................................... 7-17

7.4.4 View Group Points .......................................................................................................................... 7-18

7.4.5 Edit Output Group Templates ......................................................................................................... 7-18

7.5 Point ....................................................................................................................................................... 7-19

7.5.1 Point Programming for the SLC ..................................................................................................... 7-19

7.5.2 Point Programming For Internal or External Power Module (5496) .............................................. 7-22

7.5.3 Point Programming For 5880 and 5865 Modules ........................................................................... 7-23

7.5.3.1 Assigning a Name to a Point ................................................................................................ 7-23

7.6 System Options ...................................................................................................................................... 7-25

7.6.1 Reporting Account .......................................................................................................................... 7-25

7.6.1.1 Edit Accounts ....................................................................................................................... 7-26

Select Account (ID) ............................................................................................................. 7-26

Edit Account Number .......................................................................................................... 7-26

Select Reporting Format ...................................................................................................... 7-26

Events to Report ................................................................................................................... 7-27

Switch Attempts ................................................................................................................... 7-27

Telephone Number ...............................................................................................................7-28

7.6.1.2 Auto Test Time .................................................................................................................... 7-28

7.6.2 Phone Lines ..................................................................................................................................... 7-29

7.6.2.1 Dialing Prefix ....................................................................................................................... 7-29

7.6.2.2 Number of Answer Rings .................................................................................................... 7-30

7.6.2.3 Dial Option (TouchTone or Pulse) ....................................................................................... 7-30

7.6.2.4 Rotary Format ...................................................................................................................... 7-30

7.6.2.5 Line Monitor ........................................................................................................................ 7-30

7.6.2.6 Ground Start Relay ............................................................................................................... 7-30

7.6.2.7 Answering Machine Bypass ................................................................................................. 7-31

7.6.3 Sys. Event Outputs .......................................................................................................................... 7-31

7.6.3.1 Trouble Events ..................................................................................................................... 7-32

7.6.3.2 System Alarm Cadence ........................................................................................................ 7-33

7.6.4 Miscellaneous Options 1 ................................................................................................................. 7-33

7.6.4.1 Water Flow Delay ................................................................................................................ 7-33

Contents

151274 v

7.6.4.2 Low AC Report Delay ......................................................................................................... 7-34

7.6.4.3 Automatic Daylight Saving Time Adjustment ..................................................................... 7-34

7.6.4.4 Clock Display Format (AM/PM or Military) ....................................................................... 7-35

7.6.4.5 Change AC Line Frequency ................................................................................................. 7-35

7.6.5 Miscellaneous Options 2 ................................................................................................................. 7-35

7.6.5.1 Synchronize Strobes Active During Silence ........................................................................ 7-35

7.6.5.2 Auto Display Oldest Event .................................................................................................. 7-36

7.6.5.3 Report by Zone or by Point .................................................................................................. 7-36

7.6.6 Miscellaneous Options 3 ................................................................................................................. 7-36

7.6.6.1 Alarm Verification Time ...................................................................................................... 7-36

7.6.6.2 Plex Door Option ................................................................................................................. 7-37

7.6.6.3 Daylight Saving Time Start and End ................................................................................... 7-37

7.6.7 Edit Banner Message ...................................................................................................................... 7-38

7.7 JumpStart Autoprogramming ................................................................................................................. 7-40

7.8 Computer Account ................................................................................................................................. 7-40

7.9 Access Codes ......................................................................................................................................... 7-42

7.9.1 Profile Edit Menu ............................................................................................................................ 7-43

7.9.1.1 Edit Name ............................................................................................................................ 7-43

7.9.1.2 Edit Access Code ................................................................................................................. 7-43

7.9.1.3 Panel Functions .................................................................................................................... 7-43

Section 8

System Operation ............................................................................................................................ 8-1

8.1 Default User and Installer Codes ............................................................................................................. 8-1

8.2 Annunciator Description .......................................................................................................................... 8-1

8.2.1 LCD Displays ................................................................................................................................... 8-2

8.2.2 Banner ............................................................................................................................................... 8-2

8.3 Key Operation .......................................................................................................................................... 8-2

8.4 Menu System ............................................................................................................................................ 8-3

8.4.1 Main Menu Overview ....................................................................................................................... 8-3

8.4.2 Using the Menus ............................................................................................................................... 8-4

8.5 Basic Operation ........................................................................................................................................ 8-4

8.5.1 Setting Time and Date ...................................................................................................................... 8-4

8.5.2 Disable / Enable a Point .................................................................................................................... 8-4

8.5.3 Disable / Enable NACs by Group ..................................................................................................... 8-4

8.5.4 View Event History .......................................................................................................................... 8-5

8.5.5 Clear Event History .......................................................................................................................... 8-5

8.5.6 Conduct a Fire Drill .......................................................................................................................... 8-5

8.5.7 Conduct an Indicator Test ................................................................................................................. 8-5

8.5.8 Conduct a Walk Test ......................................................................................................................... 8-6

8.5.9 Conduct a Dialer Test ....................................................................................................................... 8-6

8.5.10 Silence alarms or troubles ................................................................................................................. 8-7

8.5.11 Reset alarms ...................................................................................................................................... 8-7

8.5.12 Check Detector Through Point Status .............................................................................................. 8-7

8.5.13 View Status of a Point ...................................................................................................................... 8-8

8.5.14 View Alarms or Troubles ................................................................................................................. 8-8

8.5.15 View System Information ................................................................................................................. 8-8

8.5.16 Reset dialer ....................................................................................................................................... 8-8

8.5.17 Communicating with a Remote Computer ....................................................................................... 8-9

8.5.18 Working with a Printer ................................................................................................................... 8-10

8.6 Operation Mode Behavior ...................................................................................................................... 8-11

8.7 Releasing Operations ............................................................................................................................. 8-14

8.7.1 Single Interlock Zone Releasing ..................................................................................................... 8-15

IntelliKnight 5808 Installation Manual

vi 151274

Conditions Required for an Pre-Alert Output Activation .................................................... 8-15

Conditions required for an General Alarm and Release Output Activation ........................ 8-15

8.7.2 Double Interlock Zone Releasing ................................................................................................... 8-16

Conditions Required for a Pre-Alert Output Activation ...................................................... 8-16

Conditions Required for a General Alarm Output Activation ............................................. 8-16

Conditions Required for a Release Output Activation ......................................................... 8-16

8.8 Smoke Alarm Verification ..................................................................................................................... 8-17

Section 9

Reporting ..................................................................................................................................................... 9-1

9.1 Receivers Compatible with the Control Panel ......................................................................................... 9-1

9.2 Reporting Formats Dialer Outputs ......................................................................................................... 9-1

Section 10

Testing and Troubleshooting ......................................................................................... 10-1

10.1 Troubleshooting ..................................................................................................................................... 10-1

10.2 Common Problems ................................................................................................................................. 10-1

10.2.1 Event History .................................................................................................................................. 10-2

10.3 Built-in Troubleshooting and Testing Tools .......................................................................................... 10-3

10.3.1 SLC Device Locator ....................................................................................................................... 10-3

10.3.2 SLC Multi Locator .......................................................................................................................... 10-4

10.3.3 I/O Point Control ............................................................................................................................ 10-5

10.4 Impedances that Cause Earth Ground Faults ......................................................................................... 10-5

Section 11

Installation Records .................................................................................................................... 11-1

11.1 SLC Device Point Record ...................................................................................................................... 11-1

Appendix A

Compatible Devices ..................................................................................................................... A-1

A.1 Two-Wire Smoke Detectors .................................................................................................................. A-14

Appendix B

Special Characters Lists .........................................................................................................B-1

B.1 Characters used for Naming .....................................................................................................................B-1

Silent Knight Fire Product Warranty and Return Policy