Silent Call Communications MR1214-MC Manuel utilisateur

Document #

1081243126052

MINI RECEIVER

Installation and Operation Manual

Model # MR1214-MC

418 MHZRECEIVER

General:

The Mini Receiver is a 418 MHz wireless alerting device equipped

with 24 hour battery backup. Main Power is supplied using a

Silent Call 18 watt AC/DC Wall mount Adapter P/N 890007-2. The

Mini Medallion Series Receiver can store up to 20 from a possi-

ble one million, Silent Call 418 MHz Medallion Series transmitter

address codes.

Installation:

Installing the Mini Receiver consists of locating it where it can be

noticed most effectively by the user. Plug the AC/DC wall mount

adapter into any standard household 110VAC 60Hz outlet. Insert

the adapters DC barrel plug into the Mini Receiver Barrel Jack

Labeled “Power”. Slide the power switch to the ON position and

conﬁrm the Power ON GREEN LED is illuminated under the top

strobe lens. The receiver is now ready to be programmed.

Programming:

NOTE:All Medallion Transmitters will be required to be pro-

grammed to your new receiver.The receiver leaves the

factory with the memory cleared.

Apply power to the receiver as described in the Installation sec-

tion.

With the receiver powered, press and hold the program button

located at the back of the receiver case. All display icons will illu-

minate. Continue to hold the program button until the icons goes

out (about 3 seconds) and then the GREEN PHONE icon blinks 3

times. Release the program button. The receiver display icons

will come back on to indicate that the receiver is now in program

mode. The receiver will remain in program mode for approxi-

mately 30 seconds, and the display icons will start to go out to

indicate the program time remaining. While in program mode,

the transmitter you wish to program must be activated (Trans-

mitting) for the receiver to memorize the code of the transmitter.

The transmitter can be activated by pressing the test button on

the corresponding transmitter. When the receiver receives the

transmitted signal, it will memorize the code. The receiver should

activate and ﬂash the top strobe light, and the appropriate display

icon will illuminate.

Programmed transmitter codes are retained in memory even

when the power is removed.

Erase memory:

To erase all programmed codes:

All Erase – Press and hold the program button, the Display icons

will come on for about 3 seconds, go off and then the GREEN

PHONE icon will blink 3 times. Continue to hold the program

button an additional 3 seconds until the icons scroll in a counter-

clockwise direction several times indicating all previous learned

transmitters that were stored in memory have been erased.

Release the program button and all previously learned transmitter

codes will have been successfully erased.

Battery Backup Mode:

In the event of a main power loss or failure of the wall adapter,

the Mini Receiver will automatically enter into the battery backup

mode. The Mini Receiver has been tested to provide at least 24

Hours of Battery backup operation with 15 minutes of Alerts.

Located under the top strobe lens cover is an AMBER LED. The

AMBER LED will blink once every 10 seconds, indicating Input

DC power loss to the receiver and it is operating on the back-up

battery. The AMBER LED will blink at a one second rate once the

back-up battery has reached minimum operating voltage. Operat-

ing the receiver during a low battery indication is not recommend-

ed.

IMPORTANT: The Mini Receiver will need to charge two hours for

every hour in Battery backup mode or a full 40 Hours after low

battery indication to ensure complete battery recharge.

Mini Receiver operating on Main power and the amber LED is ON

or blinks, indicates a failure of the unit. Return the MR1214-MC

with AC/DC adapter to the manufacturer for repair.

Battery Replacement:

The MR1214-MC Mini Receiver has a UNITECH 12VDC 800maH

Ni-MH back-up battery. Silent Call Battery Part Number (BU-12).

Replacement batteries can be ordered online at www.SilentCall.

com or by calling 800-572-5227.

Carefully follow below instructions when replacing the battery.

Replace the battery pack as follows:

1. Place the unit on its side, using a ﬂat bladed screwdriver or

similar, insert into the plastic notches on the bottom of the

unit. Gently twist blade and the bottom plastic housing will

disconnect.

2. Place the unit on its feet, and pull the front plastic housing

away from the back at the bottom until the top lens discon-

nects.

3. Hold the circuit board in place with one hand and remove the

2 pin white connector from the green battery pack by pulling

it straight out.

4. The battery is secured in place with double sided tape. To

remove the battery pack from the plastic case, hold the 2 wire

harness close to the battery pack and rock the pack back and

forth while pulling it out of the case.

5. Using the ﬂat bladed screwdriver or similar, gently remove

any excess tape from inside the plastic housing before install-

ing the new battery.

6. Remove double-sided tape protective covering from the new

battery pack before inserting into the case. Position the bat-

tery so the tape is on the top side, push the new battery into

the plastic case in the same position as the old battery.

7. Reconnect the battery by plugging in the 2 pin connector

to the circuit board, and tuck the wire harness beside the

battery.

8. Set the receiver on a ﬂat surface and position it with the front

facing you. Take the front plastic cover removed in step

2, and align it with the back cover and squeeze the bottom

portion of the two together. The top will not snap into place

because the top lens cover is in the way.

9. Lift up on the front of the top lens cover so the locking tabs

clear the plastic housing, snap the top portion of the front

and back cover together, and push the lens cover back down

and snap into place.

10. Place the ON/OFF switch to ON, Amber LED should blink at

a 10 second rate. Indicating unit is operating on sufﬁcient

battery power.

11. Plug the unit into the wall power supply. Observe the Amber

LED stops ﬂashing and stays out.

12. Perform operation test of all Fire/Smoke detectors, CO detec-

tors IAW testing section.

13. Battery replacement procedure completed.

LED Intensity Selection:

Located on the back of the receiver at the top is a switch that

will allow the user to select the brightness, or the Intensity of the

LED’s. LED intensity High, Medium, and Low selections are avail-

able. When making the selection of the LED brightness make sure

the LED strobe is off and the receiver is not processing a received

alert.

It is recommended by the National Fire Protection Agency that

when this unit is used for a ﬁre indication to use the high setting.

Operation:

When the Mini Receiver detects a signal from a Silent Call Medal-

lion Series pre-programmed transmitter, it illuminates the corre-

sponding indicator icon and activates its built-in High Intensity

LED strobe light. The indication will continue for approximately

16 seconds after the transmitted signal ceases. As long as the

Medallion Series Smoke Detector, Fire Alarm Transmitter, or CO

Detector continues to send an alert signal, the Mini Receiver alert-

ing mechanisms will remain on. The Mini Receiver has a Coded vi-

brator output for use with the Silent Call Bed Vibrator P/N VIB-PJ.

Optional Bed Vibrator Auxiliary Output:

Located on the rear of the Mini Receiver is an auxiliary output jack

labelled “Vibrator” for interfacing Silent Call VIB-PJ bed vibrator.

See the chart below for the vibration pulse pattern. The pattern

repeats during the 16 second receiver cycle.

Carbon Monoxide Transmitter

Smoke Detector or Fire

Transmitter

Three Short Pulses and One

Long Pulse

Continuous Short Pulses

Mini Receiver Display Indications and ICON Color

Carbon Monoxide Detector

CO5-MC Transmitter detects a

warning from the CO detector.

Smoke Detector or Fire Transmitter

SD4-MC/FA3-MC/FA4-MC Transmitter

detects a Smoke/Fire warning

CO Red

Red

Operational and Performance TESTING:

Test the MR1214-MC after installation, repositioning of the receiv-

er, associated transmitters are relocated, battery is replaced, the

unit is repaired, or the receiver back-up battery is replaced. Test

the Mini Receiver Fire/Smoke and CO alerts once a week to ensure

proper operation of both the Detectors transmitters and the Mini

Receiver operation. Accessory transmitters programmed into the

Mini can be tested at the user’s discrepancy.

IMPORTANT: The Environment and Building Materials may affect

the receiver reception. Locate Silent Call Medallion Series Trans-

mitters and Receivers in an area away from High Wattage appli-

ances and objects made from metals or alloys. Testing theMini

Receiver with Transmitters will help to locate a suitable location.

Fire/Smoke and CO Alert Test:

1. Program and Mount Fire transmitters and/or Smoke Detec-

tors in desired location. Reference Transmitters Installation

and Operation Manual for mounting location information.

2. Place Mini Receiver in a location to best view Strobe, Alert

Icons, and use of optional Bed Vibrator if required.

3. Mini receiver requires Power from supplied AC/DC wall

mount adapter. Plug AC/DC adapter into a 120VAC 60HZ wall

outlet.

4. Plug opposite side barrel style plug into the MINI Power input

Jack.

5. Turn Mini Receiver ON. Observe the Green LED is illuminat-

ed.

6. Remove the Barrel style power plug from the Mini Receiver

and conﬁrm the Green LED stays illuminated and that the

Amber LED begins to blinks once every 10 seconds.

7. Reinstall Barrel style Power Plug and verify Amber LED stops

blinking and stays out.

8. Plug Bed Vibrator into Mini Receiver (Optional). Be sure

3.5mm plug is fully seated into the receivers jack.

9. Set LED Intensity to desired selection. High-Medium-Low.

10. If Mini Receiver is not visible from Fire transmitter or Smoke

Detector location, a testing assistance may be required. When

testing the Transmitter and Receiver a 16 second timeout will

occur once the test button on the transmitter is released.

11. Locate and depress Fire transmitter or Smoke Detector Test

button for approximately 3 seconds and release. Observe

Mini Receiver and conﬁrm following:

12. Repeat for each Fire Transmitter/Smoke Detector and CO

detector installed weekly.

13. Test all auxiliary transmitters in the same manner. Verify

Correct ICON is displayed on front lens corresponding to the

Medallion series transmitter tested.

14. Testing Complete.

• Mini Receiver TOP THREE LED’S are ﬂashing at a 1.5HZ

rate.

• Appropriate Mini Receiver RED FIRE or CO Alert is illumi-

nated.

• Bed Vibrator is Pulsing appropriate tactile code as listed in

Optional Bed Vibrator Auxiliary Output section.

• Green LED Remains ON. Amber LED Remains OFF.

• Approximately 16 seconds after depressing Transmitter

test switch Mini Receiver will Stop Flashing the Strobe,

RED Fire or CO Light will go OUT, Bed Vibrator will no

longer pulse.

• Silent Buddy will return to Idle/Receive condition.

SPECIFICATIONS:

Frequency:

Power Adapter:

Backup Battery:

418 MHz

Grand Power Model PA1015-3HU AC to DC

Adapter. Input: 100~240 VAC 50~60Hz 0.4A

Output: 16.0 VDC 1.12A, 18 Watts Max. 12 VDC

Unitech 800 mAH Ni-MH Battery. P/N BU-12

WARNING:

Use only Battery speciﬁed in marking. Use of a different battery

will have a detrimental effect on alarm operation. Constant expo-

sures to high or low temperatures or high humidity mat reduce

battery life.

Input:

Operating Ambient

Temperature Range:

Operating Humidity Range:

Agency Listings:

16Vdc @ 0.5A Max. During Alert w/

Strobe High and VIB-PJ in use.

40° to 100°F (4.4° to 37.8°C)

15% to 95% Relative Humidity,

non-condensing

Certiﬁed to UL-217 and UL-2034

Table des matières

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur