SIIG 8000 Plus Manuel utilisateur

04-0168B

Introducing the PCI Serial 8000 Plus

The PCI Serial 8000 Plus is a high-speed PCI 8-port serial

board for use in Pentium-class computers. It's unique

4-port fan-out cables and easy-to-reach cable connectors

not only allows you to connect up to eight serial devices,

but also eliminates the inconvenience of reaching to the

back of the computer to connect devices.

Features and Benefits

•Conforms to PCI v2.1 Plug and Play

•Full support for DOS and Windows-based software

•Improves I/O access speed up to 8 times faster than

ISA serial I/O card. Reduces CPU load and

improves system performance

•IRQ sharing feature reduces IRQ conflicts

•Enhanced 128-byte Transmit and Receive FIFO

buffersachievebiggerdatablocktransfers,reducing

CPU load dramatically, especially under Windows

multi-tasking environment

•Eight high-speed 16850 serial ports (DB9) support

baud rates up to 920Kbps per port

•Ideal for high-speed serial devices including ISDN

terminal adapters, 56K V.90 external modems and

PCI Serial 8000 Plus

Quick Installation Guide

System Requirements

•Pentium or equivalent computer with an available

PCI slot

•DOS, Windows 95/98/98 SE/ME/NT 4.0/2000/

XP/Server 2003

PackageContents

• (1) PCI Serial 8000 Plus board

• (2) 4-port fan-out cable (DB37 to DB9)

• (1) 4S cable connector bracket

• (1) Driver diskette

• This quick installation guide

Layout

Figure 1. PCI Serial 8000 Plus Layout

Chipset

25-pin Connector Socket

(serial ports 5-8)

DB37 Connector

(serial ports 1-4)

Hardware Installation

General instructions for installing the card are provided

below, since the design of computer cases and

motherboards vary. Refer to your computer’s reference

manual for further information, if needed.

Caution: Static Electricity Discharge may permanently

damage your system. To avoid possible static electricity

discharge during the installation, please follow the

guidelines below:

•Discharge any static electricity build up in your

body by touching a large grounded metal surface or

the computer’s case (if plugged in), for a few

seconds.

•During the installation, avoid any contact with

internal parts. Handle cards only by their external

edges.

1. Turn OFF the power to your computer.

2. Unplugthepowercordandremoveyourcomputer's

cover.

3. Remove the slot bracket from an available PCI slot.

4. Carefully align the card to the selected PCI slot push

the board down firmly, but gently, until it is well

seated.

Figure 2. Inserting the PCI Board

5. Replace the slot bracket's holding screw to secure

the card.

Note: If you only need 4 serial ports or less, skip

steps 6 and 7 and continue to step 8.

6. Connect the 4Scable connector bracketribboncable

to the 25-pin connector socket on the board. Make

sure the stripe on the ribbon cable is on the side closest to

the slot bracket cover.

7. Install the 4S cable connector bracket, carefully

slide it into the selected slot where the slot bracket

hadbeen removed and secureit with the slotbracket

holding screw.

8. Replacethecomputercover andreconnectthepower

cord.

Connecting Cable and Devices

You can connect up to eight serial port devices to your

system via the fan-out cables which are distributed from

thetwolargeDB37 connectors. Proceedwiththefollowing

instructions for device connections:

1. Connect the 4-port fan-out cable(s) to the external

DB37 connector(s) onthePCI Serial 8000 Plus board.

Make sure the screws on the cable connectors are

well secured.

Figure 3: Connecting cables and devices

2. The serial ports are now ready to connect devices.

Note:To avoid possibly damage, turn the system

and all devices OFF before making device

connection.

Software Installation

This section provides information on how to install the

PCI Serial 8000 Plus drivers. Please make sure the board

is installed before proceeding with the driver installation.

Windows 95 Driver Installation

1. At the Update Device Driver Wizard windows,

click Next.

2. Insert the driver diskette and click Other Locations.

Type in a:\Win95, click OK, then Finish.

3. From the Insert Disk window, click OK. When the

CopyingFilesdialog boxappears,typeina:\Win95,

then click OK.

4. Remove the driver diskette and click Yes to restart

Windows.

Windows 98/98 SE Driver Installation

1. At the Add New Hardware Wizard windows, click

Next.

2. Select Search for the best driver for your device

(Recommend), then click Next.

3. Select Specify a location, insert the driver diskette

and type in a:\Win98, then click Next.

4. Click Next, Next then Finish.

5. Remove the driver diskette and click Yes to restart

Windows.

Windows ME Driver Installation

1. At the Add New Hardware Wizard, choose Specify

the location of the driver (Advanced), then click

Next.

2. Check Specify a location, uncheck the other box,

insert the driver diskette, type in A:\Win98, then

click Next.

3. Click Next andFinish to completedriverinstallation.

4. Remove the driver diskette and click Yes to restart

Windows.

Windows NT 4.0 Driver Installation

1. From the desktop click Start, then Run.

2. Insert the driver diskette, type in A:\NT4\setup,

then click OK.

3. Click Next when the Welcome window appears.

4. From Choose Destination Location window, click

Next.

5. Remove the driver diskette, select Yes to restart

Windows and click Finish.

To change the I/O address in Windows NT 4.0:

1. Double click Start, Settings, Control Panel,then

SIIG Cyber PCI 20X device icon.

2. Highlight the COM address and click Settings.

3. Select or type in an I/O address supported by the

device you would like to configure and click OK.

Make sure the selected I/O address does not

conflict with other device in your system.

4. Select Restart Now for the new setup to take effect.

Windows 2000 Driver Installation

1. At the Found New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device

(Recommended), then click Next.

3. SelectSpecify the location, uncheck the other boxes,

then click Next.

4. Insert the driver diskette, type in A:\Win2K and

click OK.

5. Click Next and Finish.

6. Click Yes to restart to complete the installation.

Windows XP/Server 2003 Driver Installation

1. AttheFound NewHardwareWizard,chooseInstall

from a list or specific location (Advanced), then

click Next.

2. Insertthedriverdiskette, check Include thislocation

in the search, ucheck the other boxes, type in

A:\Win2K and click Next.

3. At the Hardware Installation window, click

Continue Anyway, then click Finish.

Note: Ourdriverhas been thoroughly tested in Windows

forstabilityandcompatibility.

4. Repeat steps 1-3 eight more times.

5. Restart your system for the new setup to take effect.

DOS Driver Installation

1. Insert the driver diskette, from the C: prompt, type

in copy a:\dos\*.*, then press <Enter>.

2. Type in edit autoexec.bat, then press <Enter>.

3. Add C:\CB20XPC.exe at the bottom of the

autoexec.bat file.

4. Go to File, save the changes and exit.

5. Remove the driver diskette and restart your system

to complete driver installation.

Verify Proper Windows Driver Installation

For Windows 95/98/98 SE/ME:

1. From the main desktop, right click My Computer,

then click Properties. Click Device Manager tab.

2. Double click Ports (COM & LPT) and new Cyber

PCI ports should be displayed. Also, double click

SIIG Cyber PCI option and SIIG ... PCI Board

should be displayed.

For Windows NT 4.0:

1. Go to Start / Setting / Control Panel,double click

SIIG Cyber PCI 20X device icon.

2. New COM port address number will be assigned

for the ports when successfully installed. The board

is ready to connect devices.

For Windows 2000/XP/Server 2003:

1. Right click My Computer, click Manage, then click

Device Manger.

2. Click on the +(plus sign) in front of Ports (Com &

LPT).

3. New Cyber port(s) should be listed.

Technical Support

QUESTIONS? SIIG’s Online Support has the answers!

Simply visit our Web site at www.siig.com and click on

Support. Our online support database is updated daily with

new drivers and solutions. The answers to your problems

could be just a few clicks away.

If you can't find answers or solutions to your questions, you

have an option to submit the problems online to one of our

technical support analysts and we will promptly respond to

you with answers or solutions.

The 5-year manufacturer warranty supplied with this product

is offered by SIIG, Inc. If you should happen to encounter

any problems with this product, please follow the procedures

below.

1. If it is within the store's return policy period, please

return the product to the store where you purchased

from.

2. If your purchase has passed the store's return policy

period, please contact SIIG. See SIIG's Limited 5-year

Warranty card for more information.

Online Store

SIIG offers all of our products online at our company

store. Visit us at http://onlinestore.siig.com to find

our complete line of products, including hard to find

itemsandaccessories(power adapters,cables,upgrade

kits, etc.).

PCI Serial 8000 Plus is a trademark of SIIG, Inc.

SIIG and SIIG logo are registered trademarks of SIIG, Inc. DOS, Windows and Windows NT are

registeredtrademarksofMicrosoftCorporation. PentiumisaregisteredtrademarkofIntelCorporation.

Othernames usedin publicationare foridentification onlyand maybe trademarksof theirrespective

companies.

PRODUCT NAME MODEL NUMBER

PCI Serial 8000 Plus IO1875

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS

B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCCCOMPLIANCESTATEMENT:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR

PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

About SIIG, Inc.

Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer

of I/O connectivity products, including PCI & ISA serial and parallel

ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),

Networking,SoundCards, and other accessories. SIIG is the premier

one-stop source of upgrades.

SIIGproductsoffercomprehensive usermanuals,manyuser-friendly

features, and all products are backed by a 5-year manufacturer

warranty. High-quality control standards are evident by the overall

ease of installation and compatibility of our products, as well as one

ofthe lowest defective return rates in the industry. SIIG products can

be found in most computer retail stores, mail order catalogs, and e-

commerce sites in the Americas and the UK, as well as through major

distributors, system integrators, and VARs.

Table des matières

Autres manuels SIIG Carte PCI

SIIG

SIIG JJ-P02D11-S6 Manuel utilisateur

SIIG

SIIG Cyber 1S1P PCI Manuel utilisateur

SIIG

SIIG 1394 PCI Adapter Manuel utilisateur

SIIG

SIIG SIIG 2S1P Combo-Value Manuel utilisateur

SIIG

SIIG Low Profile PCI-1S1P Manuel utilisateur

SIIG

SIIG 4-Port RS232 Serial PCI with 16550 UART Manuel utilisateur

SIIG

SIIG SC-SAEE22-S1 Manuel utilisateur

SIIG

SIIG Hi-Speed USB 4-Port PCI Manuel utilisateur

SIIG

SIIG Duet Parallel PCI Manuel utilisateur

SIIG

SIIG Serial ATA 4-Channel PCI Manuel utilisateur

SIIG

SIIG CyberPro 1S1P Manuel utilisateur

SIIG

SIIG JJ-P49012-S6 Manuel utilisateur

SIIG

SIIG CyberPro PCI 8S Manuel utilisateur

SIIG

SIIG PCI Express Serial Cards Manuel utilisateur

SIIG

SIIG LB-US0614-S1 Manuel utilisateur

SIIG

SIIG DP CyberSerial Dual PCI RJ Manuel utilisateur

SIIG

SIIG UltraATA 133 PCI Manuel utilisateur

SIIG

SIIG NN2630 Manuel utilisateur

SIIG

SIIG LB-US0314-S1 Manuel utilisateur

SIIG

SIIG NN-E38012-S2 Manuel utilisateur

SIIG

SIIG Low Profile PCI-2S Manuel utilisateur

SIIG

SIIG FireWire 800 M-64 Manuel utilisateur

SIIG

SIIG CyberPro PCI 4S Manuel utilisateur

SIIG

SIIG DP Hi-Speed USB 4-Port PCIe Manuel utilisateur

Manuels Carte PCI populaires d'autres marques

ERMA

ERMA SSI 1417 Manuel utilisateur

Moxa Technologies

Moxa Technologies CP-102E Manuel utilisateur

I-Bus

I-Bus IBC2602 Manuel utilisateur

Exsys

Exsys EX-60102 Manuel utilisateur

Chelsio Communications

Chelsio Communications T5 Series Manuel utilisateur

Conrad Electronic

Conrad Electronic 97 46 71 Manuel utilisateur

Micro Innovations

Micro Innovations USB650A Manuel utilisateur

KTI Networks

KTI Networks KF-310 Manuel utilisateur

Asus

Asus SpaceLink WL230 Manuel utilisateur

TRENDnet

TRENDnet TEW-703PI Manuel utilisateur

Belkin

Belkin F5D7000F Manuel utilisateur

Pericom

Pericom PI7C7100 Manuel utilisateur

ADLINK Technology

ADLINK Technology cPCI-3548 Manuel utilisateur

Digium

Digium TE200 Series Manuel utilisateur

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur

Western Digital

Western Digital FireWire PCI Adapter Manuel utilisateur

Pyle

Pyle Gamelink PLINK1 Manuel utilisateur

Alpha Networks

Alpha Networks WMP-A13V Manuel utilisateur