SIGMA TEK SR 020 Manuel utilisateur
SR 020
S-DIAS Current Controller Module
Instruction Manual
Date of creation: 12.09.2013
Version date: 26.07.2023
Article number: 20-029-020-E
Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: +43/6274/4321
Fax: +43/6274/4321-18
Email: office@sigmatek.at
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2013
SIGMATEK GmbH & Co KG
Translation of the Original Instructions
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or dis-
tributed in any form (print, photocopy, microfilm or in any other process) without express permission.
We reserve the right to make changes in the content without notice. SIGMATEK GmbH & Co KG is not responsible
for technical or printing errors in this handbook and assumes no responsibility for damages that occur through its
use.
S-DIAS CURRENT CONTROLLER MODULE SR 020
26.07.2023 Page 1
S-DIAS Current Controller Module SR 020
with1 DC motor driver
1 Power LED driver
1 LED driver
The S-DIAS SR 020 current controller module is used to operate a DC
motor with a 12-30 V supply voltage and a maximum motor current of 3.5
A. Higher starting currents are possible for a short period.
The module also contains a current-controlled LED driver with a maxi-
mum current of 20 mA, as well as a current-controlled power LED with a
maximum of 350 mA.
SR 020 S-DIAS CURRENT CONTROLLER MODULE
Page 2 26.07.2023
Contents
1. Introduction............................................................................. 5
1.1 Target Group/Purpose of this Operating Manual......................5
1.2 Important Reference Documentation .........................................5
1.3 Contents of Delivery.....................................................................5
2Basic Safety Directives .......................................................... 6
2.1 Symbols Used...............................................................................6
2.2 Disclaimer......................................................................................8
2.3 General Safety Directives ............................................................9
2.4 Software/Training .......................................................................10
3Standards and Directives......................................................11
3.1 Directives.....................................................................................11
3.1.1 EU Conformity Declaration................................................................11
4Type Plate...............................................................................12
5Technical Data .......................................................................13
5.1 Motor Output Specifications......................................................13
5.2 Current Output Specifications...................................................14
5.3 Electrical Requirements.............................................................14
5.4 Miscellaneous .............................................................................17
5.5 Environmental Conditions.........................................................17
6Mechanical Dimensions........................................................18
S-DIAS CURRENT CONTROLLER MODULE SR 020
26.07.2023 Page 3
7Connector Layout..................................................................19
7.1 Status LEDs.................................................................................20
7.2 Applicable Connectors...............................................................20
7.3 Label Field...................................................................................22
8Wiring.....................................................................................23
8.1 Wiring Example...........................................................................23
8.2 Note..............................................................................................24
9Assembly/Installation ...........................................................25
9.1 Check Contents of Delivery.......................................................25
9.2 Mounting......................................................................................26
10 Addressing.............................................................................28
11 Transport/Storage .................................................................33
12 Storage...................................................................................33
13 Maintenance...........................................................................34
13.1 Service.........................................................................................34
13.2 Repair...........................................................................................34
14 Disposal .................................................................................34
15 SR020 Hardware Class .........................................................35
15.1 Interfaces.....................................................................................36
15.1.1 Clients............................................................................................... 36
SR 020 S-DIAS CURRENT CONTROLLER MODULE
Page 4 26.07.2023
15.1.2 Servers..............................................................................................36
15.1.3 Communication Interfaces.................................................................38
15.2 Example.......................................................................................38
Documentation Changes..............................................................39
S-DIAS CURRENT CONTROLLER MODULE SR 020
26.07.2023 Page 5
1. Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
•Project planners
•Technicians
•Commissioning engineers
•Machine operators
•Maintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found
on our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x SR 020
SR 020 S-DIAS CURRENT CONTROLLER MODULE
Page 6 26.07.2023
2 Basic Safety Directives
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes:
DANGER
Danger indicates that death or serious injury will occur, if the speci-
fied measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the speci-
fied measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
CAUTION
Caution indicates that moderate to slight injury can occur, if the speci-
fied measures are not taken.
To avoid moderate to slight injuries, observe all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
S-DIAS CURRENT CONTROLLER MODULE SR 020
26.07.2023 Page 7
WARNING
Hot Surfaces
Surfaces chaudes
INFORMATION
Information
Provides important information on the product, handling or
relevant sections of the documentation, which require atten-
tion.
SR 020 S-DIAS CURRENT CONTROLLER MODULE
Page 8 26.07.2023
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual
is regularly checked and required corrections are included in the sub-
sequent versions. The machine manufacturer is responsible for the
proper assembly, as well as device configuration. The machine opera-
tor is responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If neces-
sary, contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product descrip-
tion. It does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this operat-
ing manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.
Table des matières
Autres manuels SIGMA TEK Contrôleurs
