Siemon 7M Series Manuel utilisateur

Revision Date:

06/01/2015

Instruction Manual

Rack P

ower Distribution Unit

7M,

7N,

, 7T

and

Series

Firmware Version

.12.7

Contents

................................

............................

Specifications

................................

....................

Overview

Environmental

Electric

Receptacle Ratings

Networking

Data Formats

EMC Verification

Installation

................................

.......................

Guidelines

Mounting

Network Overview

Default IP Address

Initial Setup

Web Interface

................................

.................

Overview

Sensors Page

Logging Page

Display Page

Alarms Page

Control Page (7S and 7W Only)

Configuration Page

Unit

Configuration

................................

...........

Network Configuration

Time and Date

Mai

l/ Business Hours

SNMP

Accounts and Passwords

Telnet

Camera Configuration

Admin Information

Kilowatt

Hours Res

XML File Backup

SSL Certificate Upload

Alarms

................................

.............................

Alarm Notifications

Alarm Types

Thresholds

Sensors

................................

...........................

Overview

Internal Sensors

Data Logging and Display

Remote Outlet Switching (7S and 7W Only)

................................

....

Actions

Configuration

Power

On Actions

Accessories

................................

.....................

Serial Communication (Delta Configured Units Only)

Addressable Network Cameras

Alter

nate Data Formats

Technical Support

................................

...........

Firmware Version

rmware Updates

Resetting PDU

Service and Maintenance

re Technical Support

Table of Figures

................................

...............

Revision History

Specifications

Overview

The

7N,

and 7W

series

units

are

ack

level

PDUs with

circuit

onitoring

via a built

web server.

In the

series, b

uilt

in se

nsors monitor Voltage, Current, instantaneous and

cumulative Power, as well as

calculated Power Factor

The

series

its have all these

sensors plus

outlet level switching, while

series units are the same as the

with added

outlet level

current and power

monitoring

Web pages, including graphs,

are

generated

the

unit

monitor power and environmental conditions

within the cabinet. No software other than

a web browser is required

for operation

and several data formats are available. Optional

external sensors and network cameras are

also

available.

These units can be built for

installation in either Delta or Wye

building wiring configurations.

Environmental

Temperature

Operating

(

Vertical

)

10°C (50°F) min

40°C (104°F) max

Operating (

Horizontal

)

10°C (50°F) min

45°C (113°F) max

Storage:

25°C (

13°F) min

65°C (149°F) max

Humidity

Operating:

5% min

95% max

(non

condensing)

Storage:

5% min

95% max

(non

condensing)

Elevation

Operating:

0 m (0 ft) min

2000 m (6561 ft) max

Storage:

0 m (0 ft) min

15240 m (50000 ft) max

Electrical

See nameplate for

nit

ratings.

Receptacle Ratings

NEMA 5

15R or L5

125 Volts, 15 Amp

NEMA 5

20R or L5

20R

125 Volts, 20 Amp

NEMA 6

20R or L6

20R

250 Volts, 20 Amp

NEMA L5

30R

125 Volts, 30 Amp

NEMA L6

30R

250 Volts, 30 Amp

NEMA L15

30R

250 Volts (3 phase), 30 Amp

IEC

320 C13

125/250 Volt, 15 Amp (per Receptacle Ba

nk)

IEC

320 C19

125/250 Volt, 20 Amp

Networking

Protocols

HTTP, HTTPS (SSL/TLS), SMTP, POP3, ICMP, DHCP, TCP/IP, NTP,

Telnet

, Syslog

Ethernet Link Speed

10 M

it; half

duplex

Data Formats

HTML, SNMP, CS

V/Plain Text

, XML

EMC Verification

This

Class A

device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause undes

ired

operation.

This Class A digital apparatus complies with Canadian ICES

003.

Cet appareil numérique de la classe A est conforme à la norme NMB

003 du Canada.

Warning: Changes or modifications to this unit not expressly approved by the party responsi

ble

for compliance could void the user’s authority to operate this equipment.

Installation

Guidelines



If the PDU is installed in a cabinet the ambient temperature of the rack should be no greater

than

the PDU’s maximum rated operating temperature



Inst

all the PDU such that the amount of airflow required for safe operation of equipment is

not compromised.



Mount the PDU so that a hazardous condition is not achieved due to uneven mechanical



Follow nameplate ratings when connecting equipment to the

branch circuit. Take into

consideration the effect that overloading of the circuits might have on over

current

protection and supply wiring.



The PDU relies on the building installation for protection from over

current

conditions

. A

Listed circuit breake

r is required

with

in the building installation. The circuit breaker should

be sized according to the PDU’s nameplate ratings and local/national electrical code



Reliable earthing of rack

mount equipment should be maintained. Particular attention

should

be given to supply connections other than direct connections to the branch circuit.

The PDU must be connected to an earthed socket

outlet.



The

PDU is intended for Restricted Access Location

s only and o

nly service personnel should

install and access the PD



For pluggable equipment, install the PDU so

that

the input plug or appliance coupler may be

disconnected for service.



Sequential power

up via Power

On Actions of devices powered by

the

PDU is recommended

to avoid high inrush current. See

Power

On Actions

(page

) for details.



Caution:

Disconnect all power cords before servicing.

Mounting

Figure

: Full Length Bracket

Using the full length bracket, mount PDU to rack as shown

Figure

: Toolless Mounting Hardware

Secure toolless mounting buttons to PDU as shown. Use toolless buttons with key

holed slots

built into cabinet or with optional

Siemon

PDU

brackets

PDU & VP

PDU

002 shown)

Figure

: Adjustable Mount Brackets

Using adjustable mount brackets, attach PDU to rack as shown

Network Overview

This product

comes preconfigured

with a default IP address set

. Simply connect to the PDU and

access th

e web

page with your browser.

Default

IP Address

7N,

and

units have a

default

IP address for initial setup and access to the unit if

the

assigned address is lost or forgotten

Once an IP address is assigned to a unit, the default IP

address i

s no longer active. To restore the default IP address, press

and hold

the reset button

located below the network connector

for 20 seconds

while the unit is powered up

The Idle and

ctivity lights

next to the

network connector will both light up when

the

IP address has been

reset

The reset button is accessed through the white, circular hole located below the Ethernet

jack.

Note:

Pressing the reset button under the network connector will restore the default IP address and will

also clear all password

settings.

The Configuration page allows you to assign the network properties or use DHCP to connect to

your network. Access to the unit requires the IP address to be known, so use of a Static IP or

reserved DHCP is recommended. The

default

address is sh

own on the front of the uni



IP Address:

192.168.123.123



Subnet

Mask:

255.255.255.0



Gateway:

192.168.123.1

Initial Setup

Connect the

7N,

series

unit to your computer using a crossover cable or

hub/switch.

Windows 7

On your computer,

go to “Start > Settings > Control Panel > Network & Sharing Center”

Right click on “Local Area Connection” and select “Properties”

Change IP address and Subnet Mask as shown below:

Windows XP

On your computer, go to “Start > Settings > Control Panel

> Network and Dial Up

Connections”

Right click on “Local Area Connection” and select “Properties”

Select “Use the following IP address”. Use these settings:



IP Address:

192.168.123.1



Subnet Mask:

255.255.255.0



Gateway:

Leave blank

Click “OK” twice.

The unit should now be accessible in a web browser via the unit’s permanent IP address:

http://192.168.123.123/

. See

Unit Configuration

(page

) for details.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Siemon Unité de distribution d'énergie

Siemon

Siemon PowerMax Manuel utilisateur

Manuels Unité de distribution d'énergie populaires d'autres marques

hager

hager SP 015 Manuel utilisateur

Pakedge

Pakedge PowerPak 9 Manuel utilisateur

Pts

Pts 9042 Series Manuel utilisateur

Shure

Shure WA405 Manuel utilisateur

CORNING

CORNING CCH 4U Manuel utilisateur

Panamax

Panamax M4LT-EX Manuel utilisateur

PANCONNECT

PANCONNECT FLAT 3M Manuel utilisateur

Raytheon

Raytheon 138-118 Manuel utilisateur

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Manuel utilisateur

Botex

Botex PSA 322-6 DL Manuel utilisateur

GE QuiXtra 4000 Guide de démarrage rapide

RDL

RDL EZ Series Manuel utilisateur

StarTech.com

StarTech.com RKPW161915 Manuel du système

Vertiv

Vertiv Knürr DI-Strip Rack PDU Manuel utilisateur

ABB

ABB PSBS0065 Manuel

Baumuller

Baumuller BFN 3-1-0007-001 Manuel

Eaton

Eaton StructuredWiringSolutions ESWT41600 Manuel

GE GEK-45404F Manuel utilisateur