Siemens DB-HR Manuel utilisateur

P/N 315-033220-5

DETECTOR AND BASE PLACEMENT

Detector and base locations shall follow the drawings provided or approved

by Siemens Industry, Inc. or its authorized distributors.This is extremely

important! The detector placements shown on these drawings were chosen

after a careful evaluation of all facets of the protected area. When drawings

are not available, refer to Detector Placement section of detector Installation/

Wiring Instructions and to NFPA 72, National Fire Alarm Code and CAN/ULC-

S524.

BASE WIRING

The Model DB-HR from Siemens Industry, Inc. is a polarity insensitive detector

base and works with HFP-11, HFPT-11, HFPO-11, SFP-11*, SFPT-11* and SFPO-

11* detectors only. Detectors should be interconnected as shown in Figure 1

and wired to the DLC (refer to DLC Installation Instructions, P/N 315-033090), FS-

DLC (refer to FS-250 Installation, Operation and Maintenance Manual, P/N 315-

049353) or FDLC (refer to FS-250C Installation, Operation and Maintenance

Manual, P/N 315-049589C), as applicable. Line 1 and Line 2 can be either line of

the loop. Note any limitations on the number of detectors and restrictions

on the use of remote devices permitted for each circuit.

Figure 1

DB-HR Wiring Diagram Using HFP-11 Series and SFP-11 Series Detectors

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

*THE RELAY CONTACTS ARE

SHOWN IN THE NON-ALARM/

SYSTEM RESET CONDITION.

LINE 1 AND LINE 2 CAN BE EITHER LINE OF THE LOOP.

DO NOT USE AN END

OF LINE DEVICE

TO NEXT DEVICE

DO NOT USE AN END

OF LINE DEVICE

TO NEXT DEVICE

TO INITIATING CIRCUIT

OF SIEMENS INDUSTRY,

INC. CONTROL PANEL

REMOTE RELAY BASE

MODEL DB-HR

LINE 1

LINE 2

LINE 1

LINE 2

RELAY*

CONTACTS

3A, 120 VAC

3A, 30 VDC

DB-HR RELAY BASE

Detector Base

Installation Instructions

Model DB-HR

*SFP-11, SFPT-11 and SFPO-11 detectors are approved for use in Canada only.

DETECTOR MOUNTING USING THE DB-HR BASE

The detector is provided with a separate base which attaches to a standard 4

inch square or a 4 inch octagonal electrical box, with the box size and depth

required by the NEC for the number and size of conductors used. Wire size:

max – 14 AWG, min – 18 AWG.

Refer to Figure 2.

1. Route all wires outward from outlet box.

2. When the ALARM LED viewing is critical, position the LED mark in the

base in the intended direction.

3. Route wires through the hole in the center of the base and mount base

to outlet box. Make connections directly to the base terminals. Refer to

Figures 1 and 2 for details.

4. After all bases are installed, check wiring integrity.

5. To insure proper installation of the detector head into the base:

a. Route wires away from connector terminals.

b. Take up all slack in the outlet box.

c. Properly dress and position all wires flat against the base.

d. Check that screw terminals are tight.

P/N 315-033220-5

Figure 2

Mounting the Base

BASE

MOUNTING

HOLES

MOUNTING

HOLE COVERS

ALARM LED

LOCATION WITH

DETECTOR

INSTALLED

IN BASE

Table des matières

Autres manuels Siemens Capteur de sécurité

Siemens

Siemens FDT181 Manuel utilisateur

Siemens

Siemens Sinteso FD20 Mode d’emploi

Siemens

Siemens UP 258D11 OPTISENS OFFICE Manuel utilisateur

Siemens

Siemens Cerberus CS1140 Manuel technique

Siemens

Siemens 667/HB/47200/000 Manuel utilisateur

Siemens

Siemens FDOOT441 Manuel utilisateur

Siemens

Siemens 5SV60 MC Series Manuel utilisateur

Siemens

Siemens SIMATIC ET 200S Manuel utilisateur

Siemens

Siemens FDOOT241-A9-Ex Manuel utilisateur

Siemens

Siemens S7-1500F Manuel utilisateur

Siemens

Siemens DELTA reflex 5TC7 2 Series Manuel de service

Siemens

Siemens QRI Series Manuel utilisateur

Siemens

Siemens FDOOT271 Mode d’emploi

Siemens

Siemens DB721 Manuel utilisateur

Siemens

Siemens FDOOT271-O Mode d’emploi

Siemens

Siemens FDOOTC441 Manuel utilisateur

Siemens

Siemens Sinteso FD20 Manuel d'utilisation

Siemens

Siemens FDOOT441 Manuel utilisateur

Siemens

Siemens RAR Series Manuel utilisateur

Siemens

Siemens ADB-11 Manuel utilisateur

Siemens

Siemens L-852A-D Dualite Manuel utilisateur

Siemens

Siemens HI320C Instructions d'utilisation et d'installation

Siemens

Siemens FDT421 Manuel utilisateur

Siemens

Siemens ADM-Q12T Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur

Solinst

Solinst 301 Manuel utilisateur