Siemens LITHOSTAR Multiline Guide de configuration

LITHOSTAR Multiline

Print No.: RXL2-120.091.08.04.02 Doc. Gen. Date: 10.00

Replaces: RXL2-120.091.08.03.02

The reproduction, transmission or

use of this document or its contents

is not permitted without express

written authority. Offenders will be

liable for damages. All rights,

including rights created by patent

grant or registration of a utility

model _or_design,_are_reserved.

System Manual

Replacement of Operating PC

Repair Instructions

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 2 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

0 - 2 Revision

Chapter Page Revision

0all04

1all04

2all04

3all04

4all04

5all04

Contents 0 - 3

Siemens AG Register 5 RXL2-120.091.08 Page 3 of 4 LITHOSTAR Multiline

Medical Engineering Rev. 04 10.00 TD PS 24 System Manual

1 _______Software generation ____________________________________________1 - 1

Rear view of the operating PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

2 _______Operating PC SCENIC Pro C5/ Pro C6______________________________2 - 1

Mechanical changes in the control console . . . . . . . . . . . . . . . . . . . . . . .2 - 1

Opening the operating PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2

Installing board D51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 - 3

Closing the operating PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 4

3 _______Operating PC LM Control Unit ____________________________________3 - 1

Open operating PC and install board D51. . . . . . . . . . . . . . . . . . . . . . . . 3 - 3

Close the operating PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 - 3

4 _______Changes to previous version_____________________________________4 - 1

Page

0 - 4 Contents

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 4 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

This page intentionally left blank.

Page

1 - 1

Siemens AG Register 5 RXL2-120.091.08 Page 1 of 4 LITHOSTAR Multiline

Medical Engineering Rev. 04 10.00 TD PS 24 System Manual

Rear view of the operating PC 1

1 Keyboard port 5 Parallel interface X50 Respirator-ECG signal interface

2 Moouse port 6 Monitor port X51 DUEP port

3 Serial interface COM 1 7 Power line connector

4 Monitor power line connector

SCENIC Pro C6

Position D51

X50 X51

2356

4Position D51

LM - Control Unit

X50 X51

SCENIC Pro C5 7

X51

X50

Software generation 1

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 2 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

1 - 2 Software generation

•SwitchthesystemOFF.

•Placethenew operatingPCinthedrawerof thesystemcontrolconsole.

•Connectthe followingcablestotheoperatingPC:

- linevoltagecableforoperatingPC

- linevoltagecableformonitor

- signalcableformonitor

- signalcableformouse

- signalcableforkeyboard

•SwitchthesystemON.

The greenLED onthe operatingPC mustlightup.

•On the operatingPC.

•SwitchthesystemOFF.

•InsertthebootdiskindriveA of theoperatingPC.

•SwitchthesystemON.

•Ifthekeyboardisreplaced,theUserTerminalsoftwaremustbe reinstalled.

Answeraccordingly.

SCENIC Pro C5 / C6

Ïthe following message appears:

"MS-DOS 6.2 Startup Menü"

•usethedown arrowkey"↓" to select

"2.PCneu startenodermanuell

ausschalten"

German texts will appear during the installation of the software

→This is due to the German operating system.

NOTICE

User-Terminal-Software Installation?

No: Press [ Ctrl ]+ [ C ]

YES: Press any key, to continue

Eine beliebige Taste drücken, um fortzusetzen.

Software generation 1 - 3

Siemens AG Register 5 RXL2-120.091.08 Page 3 of 4 LITHOSTAR Multiline

Medical Engineering Rev. 04 10.00 TD PS 24 System Manual

•Afterafew moments,thefollowingcommandappears:

•Pressthe"J" key and then"Enter/Entrée".

•Thecommand to enterthe type of keyboardappears:

•Selecteither"E"or"F",dependingon the type ofkeyboard,andpress"ENTER"/Entrée".

•Afterafew moments,thefollowingcommandappears:

•Removethe boot disk from driveA.

•Insertthebackupdisk01 in drive A.

•Pressanykey.

•When the system finishesloadingbackupdisk01,the followingcommand appears:

•Remove backup disk 01from drive A.

•Insertbackupdisk02 in driveA.

•Repeatthesame procedurefortheremainingbackupdisks.

•Onceallthe backup diskshavebeen loaded,the followingmessageappears:

•Remove backup disk 05from drive A.

•InserttheUserInterfaceSWdisk in drive A.

Hard-Disk will be formatted!

Please wait 5 sec. for next message and press "J" and [ENTER ] !

WARNUNG! Alle Daten auf der Festplatte in Laufwerk C:

werden gelöscht!

Formatieren durchführen (J/N)?

Enter keyboard type:

E: englisch (international) keyboard

F: french keyboard

Press "E" or "F" according to keyboard type and press [ENTER ]:

Please insert "Backup-Disk 01... 05" (Sicherungdiskette 01... 05)!

Press any key, to continue!

Sicherungsdiskette 01 in Laufwerk A: einlegen

Eine beliebige Taste drücken, um fortzusetzen

Sicherungsdiskette 02 in Laufwerk A: einlegen

Eine beliebige Taste drücken, um fortzusetzen

Please insert disk: "User-Interface-SW"!

Press any key, to continue!

Eine beliebige Taste drücken, um fortzusetzen

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 4 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

1 - 4 Software generation

•Afterafew moments,thefollowingcommandappears:

•Remove the User Interface SW disk from drive A.

•InserttheStatusdiskindriveA.

•Afterafew moments,thefollowingcommandappears:

•Removethe Status disk from drive A.

•InsertthebootdiskindriveA.

•Afterafew moments,thefollowingcommandappears:

•SwitchthesystemOFF.

•Removethe boot disk fromdriveA.

•Fortheadditionalstepsrequired,refertothechapterwhichcorrespondsto theoperating

PC being used.

Do not activate the write protection on the diskette, since data

must be written onto it.

Please insert "Status-Disk"!

Press any key, to continue!

Eine beliebige Taste drücken, um fortzusetzen

CAUTION

Please insert "BOOT-Disk" again!

Press any key, to continue!

Eine beliebige Taste drücken, um fortzusetzen

*******A T T E N T I O N: I M P O R T A N T N O T E! *********

Modify CMOS-SETUP according to service-manual!

- CMOS-Setup-Lock by Password

- Disable Disk-Controller

See instructions!

Please remove disk!

Now, switch off the PC and turn it on again for CMOS-Setup-Modify!

Thank you!

2 - 1

Siemens AG Register 5 RXL2-120.091.08 Page 1 of 4 LITHOSTAR Multiline

Medical Engineering Rev. 04 10.00 TD PS 24 System Manual

Mechanical changes in the control console 2

•Especially in thecase oftheSCENIC ProC5: operating PC

- Replacetheexistingground conductorin the controlconsolebythelongerone from

theconversionkit4783 416.

- Connectthecablefor the DUEP connectionX51and fastenfirmlyon thetopof the

connectorbracketusingtheclipfrom the conversion kit.

- Placethewoodenconsolefrom the conversionkit4783 416 onthe drawer.

- PlacetheoperatingPCon thewooden console.

•When the message "PressF2to enterSETUP" appears,pressthe"F2"key.

TheCMOS setupmenu appears.

•Selectthe"Main"menu usingthe← →cursorkeys.

•Inthe "Main" menu, use the ↑ ↓ cursorkeystoselectthe submenu "Boot Option".

•Pressthe "ENTER"key; use "Entrée"onthe French keyboard.

•Setthe"Post Errors"menu to "No Halt on Any Errors"usingthe +/- keys

(numerickeypad).

•Selectthe"FastBoot"menu using the↑ ↓cursorkeys.

•Setthe"Fast Boot" menu to"Enabled"usingthe +/- keys (numeric keypad).

•Selectthe"QuietBoot"menu usingthe↑ ↓cursor keys.

•Setthe"Quiet Boot" menu to"Enabled"usingthe+/-keys(numerickeypad).

•Selectthe"BootSequence:1."menu using the ↑ ↓cursorkeys.

•Setthe"Boot Sequence: 1." menu tothe harddiskusingthe "-" key (numeric keypad.

(theharddiskis1; the disketteis2).

•Pressthe "Esc" key; use the "Echap"keyon the Frenchkeyboard.

•Selectthe"Advanced"menu using the ← → cursorkeys.

•Inthe"Advanced"menu, use the↑ ↓ cursorkeys toselectthesubmenu"Peripheral

Configuration".

•Pressthe "ENTER"key; use "Entrée"onthe French keyboard.

•Selectthe"DisketteController" menu using the ↑ ↓cursorkeys.

•Setthe"DisketteController"menuto"Disabled"usingthe+/-keys(numerickeypad)

•Pressthe"Esc" key; use "Echap" on theFrenchkeyboard.

•Selectthe"Security"menuusingthe← → cursor keys.

•Inthe"Security"menu, use the ↑ ↓ cursorkeystoselect"SetSetup Password".

•Pressthe "ENTER"key; use "Entrée"onthe French keyboard.

•Enterthepassword"TDRX".

•Pressthe "ENTER" key twice;use"Entrée"onthe French keyboard.

•Enterthe password"TDRX" again.

Operating PC SCENIC Pro C5/ Pro C6 2

LITHOSTAR Multiline Register 5 RXL2-120.091.08 Page 2 of 4 Siemens AG

System Manual Rev. 04 10.00 TD PS 24 Medical Engineering

2 - 2 Operating PC SCENIC Pro C5/ Pro C6

•Pressthe"ENTER" key; use "Entrée"on the French keyboard.

•Usethe↑ ↓ cursor keys to selectthesubmenu "FlashWrite".

•Setthe"Flash Write"menu to"Disabled"usingthe+/-keys(numerickeypad).

•Pressthe"Esc"key;use "Echap" on theFrenchkeyboard.

•Usethe← → cursorkeystoselectthe"Power"menu.

•Usethe↑ ↓ cursor keys to select the"APM"menu.

•Setthe"APM" menuto "Disabled"usingthe +/- keys (numerickeypad).

•If"PowerManagementMode" is notsetto "Disabled",usethe↑ ↓cursorkeys to select

"PowerManagementMode".

•Pressthe"Esc"key;use "Echap" on theFrenchkeyboard.

•Selectthe"Power"menu using the ← → cursorkeys.

•Inthe "Power" menu, use the↑ ↓ cursorkeys toselectthesubmenu"PowerManage-

mentMode".

•Setthe"Power Management Mode"menu to "Disabled" usingthe +/- keys (numeric

keypad).

•Pressthe"Esc"key;use "Echap" on theFrenchkeyboard.

•Pressthe"ENTER" key twice;use"Entrée"onthe French keyboard.

•Afteramoment, the Multiline operatingsoftwarewilldisplaythe start-upmessage:

"NoHost Communication".

•SwitchthesystemOFF.

Opening the operating PC 2

•Removeallexternalcables.

•Openthe operatingPC (1/Fig.1).

•Slidethedrivecovertothe left (2/Fig.1).

•Forthe upper part of the housing

- slightly lifttherearedge (1/Fig.2).

- slidetowardsthefront(2/Fig.2).

- liftitupwards(3/Fig. 2).

Fig. 1 Fig. 2

Autres manuels pour LITHOSTAR Multiline

Table des matières

Autres manuels Siemens Équipement industriel

Siemens

Siemens SIMATIC RTLS Guide de l'utilisateur

Siemens

Siemens WZU-485E-MOD Manuel utilisateur

Siemens

Siemens SIREMOBIL Iso-C SP Instructions d'utilisation

Siemens

Siemens ASK46 1 Series Manuel utilisateur

Siemens

Siemens CP 5624 Manuel utilisateur

Siemens

Siemens 3NW7613-4 Manuel utilisateur

Siemens

Siemens Simatic IPC520A Manuel utilisateur

Siemens

Siemens 3TL71 Manuel utilisateur

Siemens

Siemens SIMOTICS 1LE8 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200M Manuel utilisateur

Siemens

Siemens SIRIUS 3RA244-8X.32-1 Series Manuel utilisateur

Siemens

Siemens 3VA9131-0WF Series Manuel utilisateur

Siemens

Siemens NEC Article 409 Manuel utilisateur

Siemens

Siemens SIPART PS2 Manuel utilisateur

Siemens

Siemens SENTRON VL1250 Manuel utilisateur

Siemens

Siemens SICHARGE UC Mode d’emploi

Siemens

Siemens 3VL9300-3M.00 Manuel utilisateur

Siemens

Siemens Sicharge Uc 8EM4 Series Instructions d'utilisation

Siemens

Siemens RUGGEDCOM MX5000RE Manuel utilisateur

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens 3VW9011-0BB52 Manuel utilisateur

Siemens

Siemens 3NX1013 Manuel utilisateur

Siemens

Siemens SINUMERIK 840 sl Guide de démarrage rapide

Siemens

Siemens SIMATIC V4.0 SP2 Manuel utilisateur

Manuels Équipement industriel populaires d'autres marques

ABB

ABB Unifix AD Manuel

Mark 7

Mark 7 Evolution Manuel utilisateur

Husky

Husky HyPET Manuel utilisateur

bora

bora PM-1800 Manuel utilisateur

Grizzly

Grizzly T32428 Manuel utilisateur

ABB

ABB HT610965 Manuel utilisateur

ABB

ABB SafeLink Manuel utilisateur

Phoenix

Phoenix PHX-150 Manuel utilisateur

ABB

ABB A165-L32 Manuel utilisateur

ABB

ABB HT842936 Manuel utilisateur

Rioned

Rioned UrbanJet Manuel utilisateur

Hermetica

Hermetica 10 Series Manuel utilisateur

HORNER

HORNER OEE Solution Manuel utilisateur

Hammerhead

Hammerhead HG375 Manuel utilisateur

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instructions d'utilisation

ABB

ABB HT566657 Manuel utilisateur

Webasto

Webasto GSE CAN Manuel utilisateur

ABB

ABB HT614003 Manuel utilisateur