Siemens MXL Manuel utilisateur

Installation Instructions

Document No. 565-957

August 12, 2005

Siemens MXL Driver

These installation instructions only cover the

connection of the Siemens MXL Driver to the MXL

system. For hardware installation of the Modular

Equipment Controller, see document number

565–570. For hardware installation of the Power

Open Processor, see document number 565–571.

Product Description

The Siemens MXL Driver enables communication

between the APOGEE®Automation System and the

MXL system.

Product Numbers

986-83379A Siemens MXL Driver, Open Processor

with RS-485 BLN

986-83379B Siemens MXL Driver, Open Processor

with Ethernet BLN

986-83379C Siemens MXL Driver, MEC with

RS-485 BLN, 8DI, 8DO, 8AI, 8AO,

point expansion support, HOA-ready

986-83379D Siemens MXL Driver, MEC with

RS-485 BLN, 8DI, 8DO, 8AI, 8AO,

point expansion support, with HOA

986-83379E Siemens MXL Driver, MEC with

RS-485 BLN, 8DI, 8DO, 8AI, 8AO,

point expansion support, modem,

HOA-ready

986-83379F Siemens MXL Driver, MEC with

RS-485 BLN,8DI,8DO,8AI,8AO,

point expansion support, modem, with

HOA

986-83379G Siemens MXL Driver, MEC with

Ethernet BLN, 8DI, 8DO, 8AI, 8AO,

point expansion support, HOA-ready

986-83379H Siemens MXL Driver, MEC with

Ethernet BLN, 8DI, 8DO, 8AI, 8AO,

point expansion support, with HOA

Warning/Caution Notations

WARNING:

Personal injury/loss of life may occur if you

do not follow the procedures as speciﬁed.

CAUTION:

Equipment damage or loss of data may

occur if you do not follow the procedures

as speciﬁed.

Expected Installation Times

7 minutes.

Required Tools and Materials

• Flat-blade screwdriver (1/8-inch blade width).

• Wire strippers.

• Cabling and connectors. See the Connecting

the Siemens MXL Driver to the MXL System

section.

CAUTION:

Always wear an electro-static discharge

wrist strap and discharge accumulated

static before touching ﬁeld panel

components.

Prerequisites

• Driver hardware is installed according to its

respective installation instructions.

Depending on the type of installation, other

prerequisites may have to be completed.

Connecting the Siemens MXL

Driver to the MXL System

Follow these steps to connect the Siemens MXL

Driver to the MXL system:

Item Number: 565-957, Rev. 030 Page 1 of 4

Document No. 565-957

Installation Instructions

August 12, 2005

1. Follow all shutdown procedures necessary to

prevent damage to any equipment or harm to any

personnel.

2. Turn OFF power to the MEC/MBC/RBC enclosure.

3. In the MXL enclosure, locate the NIM-1R or

NIM-1W module (hereafter referred to as the

NIM-1 module). This module will be plugged into

the connectors on a MOM-2 or MOM-4 module. If

it is plugged into a MOM-4 module, note whether

the NIM-1 module is plugged into the slot closest

to the terminal block labeled TB3 or TB4.

4. If the NIM-1 is plugged into a MOM-2 module,

or if it is plugged into the slot closest to terminal

block TB4, the following instructions apply to

connections on TB4. If the NIM-1 module is

plugged into a MOM-4 module, in the slot closest

to TB3, the instructions apply to connections on

TB3.

5. Connect one end of the shielded twisted pair

cable to terminal 1 and 2 on the appropriate

terminal block, as speciﬁed above. Terminal 1

is the negative (-) terminal, and terminal 2 is

the positive (+) terminal. There is no terminal

available for the shield, so it will be connected at

the driver. (See Figure 1 and Figure 2.)

6. Connect a 120-ohm, 1/4 watt resistor between

terminals 3 and 4 of this same terminal block.

See Figure 2.

7. At the MEC/MBC/RBC, attach the +, -, and S

leads of the RS-485 cable to an FLN/PMD trunk

connector. Allow an additional 12 inches (305

mm) of cable before terminating to the connector.

The standard practice used by MXL

installers would also require a 120-ohm

resistor between terminals 1 and 2.

Do NOT install a resistor across these

terminals.

8. Turn ON power to the MEC/MBC/RBC enclosure.

9. Start any other equipment that might have been

shut down for this installation.

FLN DRIVER

MXL PANEL

TAPE BACK

SHIELD

GW1326R1

RS-485 TRUNK CABLE

(MAX 4000’/1219.2 m;

STANDARD 24 AWG LOW CAPACITANCE)

TB3

TB4

NIM-1 MODULE

120 ohms

1/4 watt

resistor

Figure 1. Connecting the Siemens MXL Driver to the MXL System.

Page 2 of 4 Siemens Building Technologies, Inc.

Document No. 565-957

Installation Instructions

August 12, 2005

TB3 or TB4

To FLN 1 on the Open Processo

120 ohms

1/4 watt

12345678910111213141516

Do NOT use

W0955R1

Figure 2. Connecting the Siemens MXL Driver to the MXL System.

ThestandardpracticeusedbyMXL

installers would also require a 120-ohm

resistor between terminals 1 and 2.

Do NOT install a resistor across these

terminals.

Siemens Building Technologies, Inc. Page 3 of 4

Document No. 565-957

Installation Instructions

August 12, 2005

Information in this document is based on speciﬁcations believed correct at the time of publication. The right is reserved to make changes as

design improvements are introduced. Product or company names mentioned herein may be the trademarks of their respective owners.

Siemens Building Technologies, Inc. Your feedback is important to us. If you have Document No. 565-957

1000 Deerﬁeld Parkway comments about this document, please send Country of Origin: US

Buffalo Grove, IL 60089-4513 them to SBT_[email protected]. Page 4 of 4

U.S.A.

Autres manuels Siemens Entraînement CC

Siemens

Siemens SINAMICS SL150 Manuel utilisateur

Siemens

Siemens Sinamics S120M Document technique

Siemens

Siemens SED2 Series Guide de l'utilisateur

Siemens

Siemens SIDOOR ATD400K Manuel utilisateur

Siemens

Siemens simovert masterdrives Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Manuel de la liste des pièces

Siemens

Siemens 3VF 9 423-1 0 Series Manuel utilisateur

Siemens

Siemens SINAMICS S120 Guide de démarrage rapide

Siemens

Siemens 3TL60 Manuel utilisateur

Siemens

Siemens SINAMICS S120 Document technique

Siemens

Siemens SINAMICS S120 Manuel utilisateur

Siemens

Siemens SINAMICS S120 Document technique

Siemens

Siemens 6SL3845-2NN41-8AD2 Manuel utilisateur

Siemens

Siemens SINAMICS G120 Manuel utilisateur

Siemens

Siemens PXC00-PE96.A Manuel utilisateur

Siemens

Siemens SINAMICS G120 Manuel de la liste des pièces

Siemens

Siemens SIMOVERT SLP Manuel utilisateur

Siemens

Siemens SINAMICS S120 Manuel utilisateur

Siemens

Siemens SINAMICS S120 Manuel utilisateur

Siemens

Siemens SINAMICS S120 Manuel utilisateur

Siemens

Siemens MICROMASTER 420 Manuel utilisateur

Siemens

Siemens SINAMICS G110D Manuel utilisateur

Siemens

Siemens SIMATIC FM 453 Manuel utilisateur

Siemens

Siemens MICROMASTER Manuel utilisateur

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Fiche technique

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

SOMFY

SOMFY JR RU 30 Manuel utilisateur

Beckhoff

Beckhoff AX8911 Manuel de l'opérateur

Minarik

Minarik MM300 Series Manuel utilisateur