Shuttle Trio64V2 Manuel utilisateur
HOT-183: Trio64V2 PCI VGA 1
Trio64V2
PCI VGA Card
User's Manual
FCC Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy. If not installed and used properly, in strict accordance with the manufacturer’s instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures :
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help and for additional suggestions.
The user may find the following booklet prepared by the Federal Communications Commission helpful
“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S.
Government Printing Office. Washington, DC 20402, Stock 004-000-00345-4
FCC Warning
The user is cautioned that changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate this equipment.
Note : In order for an installation of this product to maintain compliance with the limits for a Class B
device, shielded cables and power cord must be used.
CE Notice:
Following standards were applied to this product, in order to achieve compliance with the electromagnetic
compatibility :
- Immunity in accordance with EN 50082-1: 1992
- Emissions in accordance with EN 55022: 1987 Class B.
NOTICE
ManualVer. 1.0
Copyright 1997.
All Right Reserved
All information, documentation, and specifications contained in this manual are subject
to change without prior notification by the manufacturer.
The author assumes no responsibility for any errors or omissions which may appear in this document
nor does it make a commitment to update the information contained herein.
TRADEMARKS
All other brand and product names referred to in this manual are trademarks or registered
trademarks of their respective holders.
HOT-183: Trio64V2 PCI VGA 3
TABLE OF CONTENTS
Chapter1Introduction........................4
These card have .........................................................................4
What you'll need ? .....................................................................5
Trio64V2 PCI VGA Card Layout.............................................5
Chapter 2 Hardware Installation....... 6
Installing the Hardware.............................................................7
Chapter 3SoftwareInstallation.......... 8
Software Drivers Support..........................................................8
How to Install Trio64V2 Drivers ?...........................................8
Microsoft Windows 3.1 Drivers Installation............................9
Microsoft Windows 95 Drivers Installation...........................10
Installing Windows NT 3.51 Display Drivers........................11
Installing Windows NT 4.0 Display Drivers..........................12
Installing AutoCAD R12/R13 Drivers...................................13
Installing Trio64V2 DOS Utilities.........................................14
Chapter 4 Windows Drivers Setup... 15
Appendix AVideo Mode Table......... 22
Appendix B Windows Drivers Setup24
HOT-183: Trio64V2 PCI VGA 4
CHAPTER 1
Introduction
The Trio64V2 PCI VGA CARD is a true 64-bit PCI accelerators. It incorporates
Trio64V2's graphicsand multimediasinglechip, to performhighspeed fills,line
draws,BitBlts, masking,and scissoring functionsin acceleratedmodes.
The Trio64V2 PCI VGA card also support high quality video playback in true
colormodes withupto 30 frames/sec.
Thisproduct ismore thanjust ahardware accelerator card. Itcomes complete
withextensive driversandcomprehensive software utilitiesdesignedto enhance
your productivity.
These cards have:
Highperformance 64-bitgraphics engine.
Integrated24-bit RAMDACandprogrammable dual-clock
synthesizer with 170 MHz output pixel rate.
UniqueS3StreamsProcessorforhardware-assistedvideo
playback.
S3Scenic Highwayfor directinterface tolivevideo andMPEG-1
peripherals.
Fullsoftware supportdrivers forWindows 3.11,Windows NT,
andWindows 95.
FullyVGA compatiblein bothhardware and software.
Supportall theVGA, super VGA,and multi-syncmonitors.
Easy installation for both hardware and software.
HOT-183: Trio64V2 PCI VGA 5
What you'll need ?
Computer System - Intel 486, Pentium, Pentium Pro or
compatible.
Expansion Slot - Require at least one PCI bus slot.
Operating System- DOS 5.0 or higher, Windows 3.1, OS/2 2.1
orhigher.
Monitor - VGA, supporting minimum 640 x 480 resolution.
DisplayDrivers- Any standard VGA or VESA drivers. For best
performance,use theTrio64V2drivers suppliedwiththese cards.
TRIO64V2 PCI VGA Card Layout
HOT-183: Trio64V2 PCI VGA 6
CHAPTER 2
Hardware Installation
Trio64V2 PCI VGA card automatically detects whether you are using a
monochromeor colormonitor. Therefore, themonitor must beturned onbefore
thecomputer, oran incorrectmonitortype maybe detected. Thiscardsupports
mostanalog monitorson themarket. If monitortype is notdetected during
power-up,the cardwill default tosupport monochromeVGA.
Thesecards shouldbe configured forthe bestresolutionand refreshrate your
monitorcan support. Checkthespecifications ofyourmonitor for signal
compatibilitywith thiscard andfind an optimumsetting tosuit yourapplications.
Installing the Hardware
Staticelectricity candamagesensitive electronic components.
Dischargeyour body'sstatic electric chargeby touchinga
groundedsurface. e.g.,the metalareaof thecomputer chassis
beforeperforming any hardwareprocedure.
The manufacturer assumes no liability for any damage, caused
directlyorindirectly, by improperinstallationofany compo-
nentsby unauthorizedservicepersonnel. If youdonot feel
comfortableperforming theinstallation,consult a qualified
computertechnician.
WARNING !!
HOT-183: Trio64V2 PCI VGA 7
Procedure
1 . Poweroffthecomputeranddisconnectthemonitorcable.
2 . Removethe computercover. If necessary, consultyoursystem
manualfor removalinstructions.
3 . Make sure the jumper setting and memory configuration are correct.
4 . Selectan emptyPCI expansionslot forthe Trio64V2PCI VGA card.
Withthe slotcoverremoved, grasp thecardby thetopedge and
carefullyseat itfirmly into theslot. Fasten theretainingbracket with
a screw.
5 . Reinstallthe computercover.
6 . Connectthe monitorcable to theVideo Output connector of the PCI
VGAcard.
Ifthesystem successfullypowersupand the normalDOSboot-upmessage
appears on the screen, the Trio64V2 PCI VGA card is installed properly. If the
systemdoes notboot, thereare a fewthings youcan checkinthe following
"Hardware Troubleshooting" section.
HOT-183: Trio64V2 PCI VGA 8
CHAPTER 3
Software Installation
Software Driver Support
The "Software Installation Diskette" supplies drivers for the following operating
systems and programs.
Windows3.1 Windows NT3.51
Windows NT4.0 Windows 95
AutoCAD 12/13/3D Studio Microstation
How To Install Trio64V2 Drivers ?
Trio64V2Drivers containon servalpiecesof floppydiskettes oronepiece ofCD-
ROM.
To begin installation DOS utilities/Windows NT drivers, insert the "DOS Utilities
& Drivers and Windows NT3.51/4.0" disk in drive A: ( or drive B:) or CD-ROM
in CD-ROM drive.
Tobegin installation Windows3.1/95drivers,insert the"Windows3.1/95
drivers" disk in drive A: ( or drive B:) or CD-ROM in CD-ROM drive.
Ifyou areinstallingdrivers forWindows3.1, WindowsNTand Windows95
please make sure that you change your display setting back to VGA mode (640 x
480x 16colors)before beginning installation.
Pleaserefer tothe followingsections forinstallationof specificdrivers.
HOT-183: Trio64V2 PCI VGA 9
Microsoft Windows 3.1 Drivers Installation
Tomake installationmoreuser friendly,theinstallation diskprovides aneasy
waysfor Windows3.1 driverinstallation.Before youinstall thewindows3.1
drivers,make surethat youchange your displaysetting tostandard VGAmode.
1. Start Windows using the standard VGA driver.
2. Insert"Windows 3.1/95"Drivers Disketteinto driveA:or driveB:.
From the File Manager or using the "File" and "Run..." pull-down
command to execute the SETUPprogram fromthe floppydrive
containing the S3 Trio64V2 Windows driver disk. or
Insert CD-ROM into CD-ROM drive. From the File Manager or using
the"File" and"Run..." pull-downcommand toexecutethe SETUP
programfrom theCD-ROMdrive Win31directorywhich containing
theS3 Trio64V2 Windowsdriver.
3. Afteryou've donewith step2. TheTrio64V2 Windows3.1 driver
installation menu will appear on screen. The setup program will
promptthe defaultpath anddirectorywhere thedrivers and
Trio64V2 tool will copy to. You may specific another path or
directoryif youwish, then clickon the"OK"icon tobegin driver
installation. Theinstallation programwillcomplete installing
Trio64V2windows 3.1driverfor you.
HOT-183: Trio64V2 PCI VGA 10
Microsoft Windows 95 Drivers Installation
Tomake installationmoreuser friendly,theinstallation diskprovides aneasy
waysfor Windows95 driverinstallation. Beforeyou installthe windows 95
drivers,make surethat youchange your displaysetting tostandard VGAmode.
1. StartWindows 95using thestandard VGA driver.
2. Click the "Start" button.
3. Doubleclick onthe Displayicon inthe"Setting ->ControlPanel"
folder. You can also click the right mouse button anywhere on the
desktopand selectthe “Properties”option fromthepop-out menu.
4. Clickthe “Settings”tab.
5. Clickthe “ChangeDisplay Type”button.
6. Clickthe “Change”button onthe rightof thefirst item “Adapter
Type”.
7. Click the “Have Disk..” button and “Install from Disk” box will
appear.
8. Click“Browse” buttonand“Open” box appears.
9. Select your A: floppy drive (or CD drive) in the “Drives” selection on
thebottom.
10. Double click “Win95” in the “Folders” selection.
11. “S3TrioV2.inf”appearsinthe filename selection.
12. Click “OK” button.
13. You will see a list of Trio64V2 cards. Select type of your VGA card
and click “OK”.
14. Aftercopying allfiles ofthe driver, itwill backto “ChangeDisplay
Type”.
15. SelectMonitor typeif necessary.
16. Click“Close” buttonand “DisplayProperties” box appears.
17. Click “Apply” button and “System Setting Change” box appears.
18. Click “Yes” to restart your Windows 95.
Table des matières
Autres manuels Shuttle Carte vidéo
Manuels Carte vidéo populaires d'autres marques
Gainward
Gainward GeForce GTX 690 4GB Manuel utilisateur
ATI Technologies
ATI Technologies RADEON 137-40225-20 Manuel utilisateur
MSI
MSI N220GT series Manuel utilisateur
ATI Technologies
ATI Technologies RADEON 7000 MAC EDITION Manuel utilisateur
SIIG
SIIG aurora Manuel utilisateur
ClearSpeed
ClearSpeed ClearSpeed Advance e720 Manuel utilisateur
