Shure Microflex MX424/N Manuel technique
MX400 Series
Gooseneck Microphones
Online user guide for Shure Microflex MX400 Series miniature gooseneck-mounted electret condenser microphones.
Version: 5 (2019-J)
Shure Incorporated
3/11
•
•
•
•
•
•
•
•
MX400 Series
Gooseneck Microphones
General Description
Shure Microflex MX400S Series microphones are miniature gooseneck-mounted electret condenser microphones designed
primarily for speech and vocal pickup. They can be mounted on lecterns, pulpits, or conference tables. All models include a
preamplifier and are available with interchangeable cardioid, supercardioid, or omnidirectional cartridges.
Wide dynamic range and frequency response for accurate sound reproduction
Interchangeable cartridges that provide an optimal polar pattern choice for each application
Shock mount provides over 20 dB of isolation from surface vibration noise
Snap-fit foam windscreen
RF filtering
MX400 microphones are available with 305 mm (12 in.) or 457 mm (18 in.) goosenecks, with or without a mute switch. They
are available in supercardioid, cardioid and omnidirectional polar patterns.
"S" models include a mute button and LED.
"D" models include a desktop base with programmable mute button and LED and logic input and output.
"SE" models feature a surface mount flange with side-exit cable.
The polar pattern of the included cartridge is indicated by a model number suffix:
/C Cardioid
/S Supercardioid
/O Omnidirectional
/N Cartridge not included
Interchangeable Cartridges
®
Shure Incorporated
4/11
•
•
Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.
Snap-Fit Windscreen
Snap into the groove below the cartridge.
To remove, spread the gap with a screwdriver or thumbnail.
Shure Incorporated
5/11
•
•
•
•
•
•
Provides 30 dB of "pop" protection.
Preamp Gain
If necessary, the preamplifier gain can be reduced by 12 dB. Contact an authorized Shure service center for information.
Microphone Placement
Aim the microphone toward the desired source, such as the talker.
Aim it away from any unwanted source, such as a loudspeaker.
Place the microphone within 15 to 30cm (6 to 12 in.) of the desired sound source.
Always use the supplied windscreen or optional metal windscreen to control breath noise.
If four or more microphones will be open at the same time, use of an automatic mixer, such as the Shure SCM810 or
SCM410, is recommended.
Permanent Installation
Mount the microphone using one of the following methods.
Shure Incorporated
6/11
1.
2.
3.
4.
5.
1.
2.
3.
4.
Flange
Drill a 22 mm (7/8 in.) diameter hole in the desired location.
Trace and drill three starter holes for the supplied screws using the flange as a template.
Insert the preamplifier through the mounting flange.
Slip the mounting flange retaining ring over the bottom of the preamplifier and slide it up until it is flush to the bottom of
the flange. Then press the ring firmly into place.
Secure the flange to the mounting surface with three screws.
Shock Mount
Drill a 44mm(1-3/4 in.) diameter hole in desired mounting surface.
Mark and drill starter holes for screws, using shock mount as a template.
Secure shock mount to mounting surface with screws.
Thread the supplied adapter onto the MX400 microphone before inserting it into the shock mount.
Shure Incorporated
7/11
Specifications
Type
Electret Condenser
Frequency Response
50–17000Hz
Polar Pattern
MX412/C, MX418/C Cardioid
MX412/S, MX418/S Supercardioid
Shure Incorporated
8/11
Output Impedance
180Ω
Output Configuration
Active Balanced
Sensitivity
@ 1 kHz, open circuit voltage
Cardioid –35dBV/Pa(18 mV)
Supercardioid –34dBV/Pa(21 mV)
1 Pa=94 dB SPL
Maximum SPL
1 kHz at 1% THD, 1 kΩ load
Cardioid 124dB
Supercardioid 123dB
Self Noise
A-weighted
Cardioid 28dBSPL
Supercardioid 27dBSPL
Signal-to-Noise Ratio
Ref. 94 dB SPL at 1 kHz
Cardioid 66dB
Supercardioid 68dB
Dynamic Range
1 kΩ load, @ 1 kHz
96dB
Common Mode Rejection
10 Hz to 100 kHz
45dB, minimum
Clipping Level
at 1% THD
–6dBV (0.5V)
Polarity
Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR
connector
Mute Switch
MX412S/MX418S
–50dB minimum
Shure Incorporated
9/11
Environmental Conditions
Operating Temperature –18–57°C (0–135°F)
Storage Temperature –29–74°C(–20–165°F)
Relative Humidity 0–95%
Power Requirements
11–52 VDC, 2.0mA
Shure Incorporated
10/11
Certifications
Meets essential requirements of all applicable European Directives.
Eligible for CE marking.
The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact
information please visit www.shure.com
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
Ce manuel convient aux modèles suivants
12
Table des matières
Autres manuels Shure Microphone
Shure
Shure Sonobar 577A Manuel utilisateur
Shure
Shure WH10 Manuel utilisateur
Shure
Shure BG 1.0 Manuel utilisateur
Shure
Shure MV5 Manuel utilisateur
Shure
Shure PG42 Manuel utilisateur
Shure
Shure SM63 Manuel utilisateur
Shure
Shure SM96 Manuel utilisateur
Shure
Shure M44G Manuel utilisateur
Shure
Shure 520DX Manuel utilisateur
Shure
Shure Spher-O-Dyne 533SA Manuel utilisateur
Shure
Shure KSM44 Manuel utilisateur
Shure
Shure WCM16 ISOMAX Manuel utilisateur
Shure
Shure ROSWELLITE KSM353 Manuel utilisateur
Shure
Shure PGA27 Manuel utilisateur
Shure
Shure A910-HCM Manuel utilisateur
Shure
Shure SM89 Manuel utilisateur
Shure
Shure 588SA Manuel utilisateur
Shure
Shure PE53 SPHER-0-DYNE Manuel utilisateur
Shure
Shure Microflex MX415 Manuel utilisateur
Shure
Shure R174 Manuel utilisateur
