Shure 588SA Manuel utilisateur

MODELS 588SA, 588SB, AND 588SBE UNISPHERE

UNIDIRECTIONAL DYNAMIC MICROPHONES

General:

The Model 588SA, 588SB, and 588SBE Microphones are unidirectional

dynamic microphones with a very effective filter that provides excellent protection

from wind and "pop" (explosive breath sounds). They feature a natural, life-like

reproduction of music and voice, and are ideal for use with good quality sound

systems and tape recorders.

These microphones are particulariy suitable for use in theatres, night clubs,

auditoriums, schools, churches, indoors or outdoors, and any place where omni-

directional microphones may not operate properly because of feedback problems.

These microphones will, in almost every instance, eliminate the annoying loudspeaker

"squeal" caused by feedback and can be used closer to loudspeakers than usual,

without feedback. This suppression of feedback, combined with their smooth sound,

makes these microphones ideal for use with orchestras, small combos, and vocalists.

The microphones feature

built-in wire-mesh screen with a special filter that provides protection from

wind "pop" (explosive breath sounds). This filter also enables singers and

speakers to perform close to the microphone.

A true cardioid pattern: symmetrical about axis and uniform at all frequencies.

This means that voice and music tonal quality remain the same, even if the

artist or speaker moues about while performing or speaking-and that feedback

and boominess are eliminated or effectively suppressed.

Cartridge shock mounted for quiet operation.

built-in "ON-OFF" switch with provision for locking switch in its "ON"

position.

Versatility-for use in the hand or on a stand--indoors or outdoors.

adjustable swivel adapter that enables you to aim the microphone where you

want it. Swivel, also, allows for quick removal for use as a hand microphone.

The Model 588SA is high impedance and may be used with any high gain

amplifier with an input of 100,000 ohms or more.

The Model 588SB and 588SBE are low impedance and designed for connection

to a 25 to 200 ohm line or input. This is recommended where long cable lengths

are required or where there are conditions of severe hum disturbance. To use the

Model 588SB or 588SBE with a high impedance amplifier, use a Shure Model A95A

or A95P Line Matching Transformer. The 588SB has 15 feet of cable, the 588SBE

has 30 feet.

Important:

Shure Microphone Cables are selected after exhaustive tests to insure

superior performance in microphones becausc of low capacities, superior shielding

properties and unusually long life under severe use.

Cables with plastic insulation should not be subjected to excessive soldering-iron

heat. Carefully clean and tin the conductors and the connections to which the con-

ductors are to be soldered. The soldering operation can then be done with a minimum

of heat, thereby avoiding any possibility of damage to the cable.

Guarantee:

Each microphone is guaranteed to be free from electrical and mechanical

defects for a period of one year frcm date of shipment from factory, provided all

instructions are complied with fully. In case of damage, return the microphone to the

factory for repairs. Our guarantee is voided if the microphone is subjected to accident

or abuse.

FIJKNISHED ACCESSORY

Swivel Adapter

............................................................................................................

A25B

OPTIONAL ACCESSORIES

............

Line Matching Transformer

......

A95A Vibration-Isolation Stand S39B

Line Matching Transformer

......

A95P Quick Disconnect Isolation Unit

....

A45

Desk Stands

..................

S38B or S33B Accessory Carrying Case

............

AC56

REPLACEMENT COMPONENTS

Swivel Adapter

............................

A25B Cable Assembly

90A1504

..........(

for Model 588SA)

Dynamic Cartridge

..................

99C355 C59

..................(

for Model 588SB)

C59E

..............(

for Model 588SBE)

(21

mm)

OVERALL

DIMENSIONS

FIGURE

ARCHITECT'S SPECIFICATIONS

The microphone shall be Shure Model 588SA (588SB, 588SBE) or equivalent.

The microphone shall be a moving-coil dynamic type microphone with a shaped

frequency range of 80 to 13,000

Hz.

This unit shall have a Cardioid polar charac-

teristic. The cancellation at the sides shall be approximately 6 db, and the cancel-

lation at the rear shall be 15 to 20 db.

Model 588SA-The microphone shall be high impedance for connection into a

high impedance input.

The microphone output shall be -59.0 db where 0 db

volt per microbar.

The microphone rating impedance shall be 40,000 ohms and the Gm (sensitivity)

at 1,000

Hz.

shall be within

db of --155.0 db referenced to EIA Standard

SE-105, August 1949.

Model 588SB, 588SBE-The microphone shall be low impedance for connection

into

25 to 200 ohm line.

The microphone output shall be -60.0 db where 0 db

1 milliwatt with 10

microbars.

The microphone rating impedance shall be 150 ohm and the Gm (sensitivity) at

1,000

Hz.

shall be within

3 db of -153.0 referenced to EIA Standard SE-105,

August 1949.

The Model 588SA (588SB, 588SBE) shall be provided with a swivel adapter

adjustable through 90" from vertical to horizontal. The microphone is equipped with

a built-in "ON-OFF" switch and a one conductor (588SA) or a two conductor

(588SB, 588SBE) shielded cable having Cannon XLR-3-11C connector on micro-

phone end. The microphone swivel adapter will mount on a stand having a %"-27

thread. The overall dimensions shall be 61%2" (164.3mm) in length and 2%"

(54.0 mm) in diameter.

XL-3-IP

rCANNoh

XL-3C

@HL;i

LEMENT

SHILLD

CIBIE-PLUG

ASSEMBU

PUBlilVF

PRFSSURE

PRCOUCLS

POSITIVE

"OLTnGE

'I.

ChRTRiOliE

PLUG

ELEMENT

BHiELD

;;

I I

CODED

TERMNIZL

CISE

GROUND

ClBLE~PLUU

ASSEMBLY

POSITIVE

PRESSURE

PRODUCES

POSITIVE

YOLTaGE

MODEL 588SA MODEL 588SB AND 588SBE

INTERNAL CONNECTIONS

FIGURE

FREQUENCY

HERTZ

FREQUENCY RESPONSE

FIGURE

Type

Frequency

Response

Polar Pattern

Impedance

OutputLevel

Switch

Shock Mount:

Cable

SPECIFICATIONS

Dynamic

80 to 13,000

Hz.

(cps) (See Figure

Cardioid (Unidirectional) pattern-Effective rejection of sound

at rear of the microphone is uniform at all frequencies, while

front pickup characteristics are uniform about the axis. See

Figure

Model 588SB and Model 588SBE

..............................

25 to 200 ohms

Model 588SA

..............................................................

High Impedance

1,000 Hz. (cps) response

Model 588SB and Model 588SBE

..............................

Low Impedance

Open circuit voltage

.............................

81.5 db

(.085mv)

Power Level

.............................................

60.0 db

EIA Microphone Rating

Gm (Sensitivity)

.................................

-153.0 db

***

Model 588SA

..............................................................

High Impedance

Open circuit voltage

..............................

59.0 db

(1.11mv)

EIA Microphone Rating

(Sensitivity)

.................................

-155.0 db

***

0 db

1 volt per microbar

0 db

1 Milliwatt with 10 microbars

***

0 db

EIA Standard SE-105, August 1949

Built-in "ON-OFF" switch with lockplate furnished. Microphone

is shipped with lockplate installed. To lock switch in "ON" position,

loosen screw on lockplate and turn lockplate 180." Tighten screw.

Internal vibration-isolation of rubber construction.

Highly durable cable with exceptionally effective hum shielding

and with Cannon XLR-9-11C connector on microphone end.

Model 588SB

............

15 foot, two-conductor shielded, rubber jacketed

Model 588SBE

.........

30 foot, two-conductor shielded, rubber jacketed

Model 588SA

...........

15 foot, one-conductor shielded, plastic jacketed

Case

Chrome plated die cast with chrome plated steel screens.

Dimensions: See Figure

Net Weight: 12 ounces,

340

grams (less cable)

27A637

1-69)

U.S. Patents, 3,132,713

and

3,240,883

Printed

U.S.A.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Shure Microphone

Shure

Shure KSM42 Manuel utilisateur

Shure

Shure Controlled Magnetic 444D Manuel utilisateur

Shure

Shure PG42 Manuel utilisateur

Shure

Shure 444D Manuel utilisateur

Shure

Shure 527B Manuel utilisateur

Shure

Shure 514B Manuel utilisateur

Shure

Shure ALTA PGA181-XLR Manuel utilisateur

Shure

Shure Microflex MX396 Manuel utilisateur

Shure

Shure ROSWELLITE KSM313 Manuel utilisateur

Shure

Shure SM96 Manuel utilisateur

Shure

Shure BETA54 Manuel utilisateur

Shure

Shure Microflex MX391BP Series Manuel utilisateur

Shure

Shure R96 Manuel utilisateur

Shure

Shure Easyflex EZG/12 Manuel utilisateur

Shure

Shure Microflex Advance MXA910 Manuel utilisateur

Shure

Shure ULX Wireless System Manuel utilisateur

Shure

Shure Microflex MX400 Series Manuel utilisateur

Shure

Shure 526T Series II Super Punch Manuel utilisateur

Shure

Shure PGA27 Manuel utilisateur

Shure

Shure PE585 UNISPHERE Manuel utilisateur

Shure

Shure Microflex MX183 Manuel utilisateur

Shure

Shure 520DX Manuel utilisateur

Shure

Shure MV51 Manuel utilisateur

Shure

Shure SM58 Manuel utilisateur

Manuels Microphone populaires d'autres marques

IK Multimedia

IK Multimedia iRig Stream MIC PRO Manuel utilisateur

DAPAudio

DAPAudio RM-101 Manuel utilisateur

AKG

AKG CHM 21 Manuel utilisateur

Sennheiser

Sennheiser evolution wireless series EM 100 Manuel utilisateur

Sony

Sony C-48 Manuel utilisateur

GIGAMEDIA

GIGAMEDIA GGM PAMICUHFG Manuel utilisateur

auna PRO

auna PRO MIC-900 Manuel utilisateur

AKG

AKG D 3800 Manuel utilisateur

MAIIN SOUND

MAIIN SOUND IIN style Manuel utilisateur

Earthworks

Earthworks TC25 Manuel utilisateur

Sennheiser

Sennheiser evolution D1 Manuel utilisateur

Alesis

Alesis MicLink Wireless Manuel utilisateur

DSPPA

DSPPA D6234 Manuel utilisateur

Monacor

Monacor IMG STAGELINE ECM-300B Manuel utilisateur

Ansr Audio

Ansr Audio Scan16 Manuel utilisateur

JLab

JLab GO TALK Manuel utilisateur

Renkforce

Renkforce TY-109 Manuel utilisateur

Trust

Trust 31008 Manuel utilisateur