Shure RK100PK Manuel utilisateur

Model RK100PK and RK100PKW Microex®

Preampler Kit User Guide

27A3252 (Rev. 1) Printed in U.S.A.

INSTALLATION - RK100PK (BLACK), RK100PKW (WHITE)

The RK100PK and RK100PKW preamp comes assembled for

use with microphones using a miniature 4-pin connector. To wire a

microphone cable directly to the preamp, follow these instructions:

Turn screw (A) counter-clockwise until it recedes below

the case.

Remove the cap (C) by removing the set screw (B) with

the provided hex wrench (.05 in.).

FIGURE 1

Push the circuit board out from the case interior to expose

the black and red wires (D).

Unsolder the wires from the circuit board (E).

FIGURE 2

Insert the rubber ex relief (G) into the cap (C) and feed

through the microphone cabling.

Note: You will need to reuse the rubber ex relief from your old

preamp. If the rubber ex relief is unavailable, please contact the

Shure Service Department.

FIGURE 3

Solder the wires directly back onto the circuit board.

Match wires as marked on the circuit board using the fol-

lowing key:

R = RED

B = BLACK

S = (GROUND) SHIELD

FIGURE 4

Push the circuit board back into the case, making sure

that the set screw (A) is lined up with the screw hole in

the side of the case (if the circuit board does not go in

all the way, twist it slightly until the screw and hole are

aligned). Raise the set screw (A) by turning clockwise

so that the preamplier is held securely in place. Screw

on the cap (C). Do not use the set screw with the cap.

SHURE Incorporated http://www.shure.com

United States, Canada, Latin America, Caribbean:

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446

Europe, Middle East, Africa:

Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414

Asia, Pacific:

Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

PIN-OUT FOR SHURE BODYPACK TRANSMITTERS AND PREAMPS - TA4M /

TA4F

How do I connect a headset to a bodypack?

(/s/article/how-do-i-connect-a-he

adset-to-a-bodypack)

145

How do I connect a Sennheiser MKE2 to a

Shure bodypack? (/s/article/how-do-

i-connect-a-sennheiser-mke2-to

-a-shure-bodypack)

1.52K

How do I connect a Sony lavalier to a Shure

bodypack? (/s/article/how-do-i-conn

ect-a-sony-lavalier-to-a-shure-bo

dypack)

219

How do I connect an AKG CK77 to a Shure

bodypack? (/s/article/how-do-i-conn

ect-an-akg-ck77-to-a-shure-body

pack)

345

How do I connect an AKG C410 or C407 to

a Shure bodypack? (/s/article/how-do-

i-connect-an-akg-c410-or-c407-to

-a-shure-bodypack)

188

FIND AN ANSWER

Browse our vast Answer database for answers to many common technical questions.

Search the Knowledge Base...

Question

What is the pin-out for Shure bodypack transmitters?

Answer

Product Model Wiring

Wireless bodypack

transmitters - all

models with TA4M

connectors

MX1BP

Battery/Phantom

Preamplifier

RK183PK Microflex

Preamplifier (see

below for RF

Resistant RK100PK

preamp model)

RPM626 BETA

Preamplifier

Pin 1: Shield

Pin 2: Bias (+5Vdc)

Pin 3: Audio

Pin 4: Bias return - 20 k Ohm resistor to ground or

equivalent active bias management circuit

(jumpered to pin 3 when used with most condenser

microphones)

RK100PK Wired

Preamplifier

Connector Body: Shield

Pin 1: Unused

Pin 2: Bias (+5Vdc)

Pin 3: Audio

Pin 4: Bias return - active bias management circuit

(jumpered to pin 3 when used with most condenser

microphones)

The pictorial shows the pin layout of a TA4F connector, as viewed from the

wiring side. If you use a bright light and look at the female connector (TA4F)

used for the cable, you will see numbers next to each hole.

Applications:

Condenser Microphones - Shure WH30, PG30, WL18x, WL50, WL51, WL93,

etc.

- Connect audio lead (black) to pins 3 and 4

- Connect bias lead (red) to pin 2

- Connect shield to pin 1 and connector body (use cable clamp insert piece as

the connector body terminal)

R6 and R4

R13 and R16

C10

C11

Snap-Fit Windscreen

• Snap into the groove

below the cartridge.

• To remove, spread the

gap with a screwdriver

or thumbnail.

• Provides 30 dB of "pop"

protection.

• Wide dynamic range and frequency response

for accurate sound reproduction

• Interchangeable cartridges that provide a

choice of polar pattern for each application

• Rotatable tie-clip that pivots in 90° increments

for placement flexibility

• Dual tie-clip and belt-clip preamp

• Supplied with snap-fit foam windscreen that

controls breath noise

• Balanced, transformerless output for increased

immunity to noise over long cable runs

• RF filtering

Windscreen

Foam Screen

Slip the windscreen over the top of microphone

so it covers side slots. The foam windscreen pro-

vides 5 to 10 dB of "pop" protection.

Interchangeable Cartridges

Microflex microphones

use interchangeable car-

tridges that allow you to

choose the polar pattern

for different installations.

RFI Filtering

Important: Microphones must be used with the

RK100PK preamp to optimize RF immunity.

Preamp Gain

If necessary, the preamplifier gain

can be reduced by 12 dB. Contact

an authorized Shure service center

for information.

R183 Omnidirectional

MX100

Shure Microflex®MX100 Series microphones are

wired lavalier electret condenser microphones

designed for speech and vocal pickup, general

purpose sound reinforcement, recording, and re-

mote monitoring applications. They can be clipped

to neckties, lapels, and other articles of clothing.

Interchangeable cartridges make it possible to

easily reconfigure microphone coverage as the

need arises.

Lavalier Microphones

R184 Supercardioid

R185 Cardioid

12mm

(0.46in.)

1.2 m

(4ft.)

22mm

(0.85in.)

99mm

(3.89in.)

20mm

(0.79 in.) 19mm

(0.75 in.)

赤

NERO

RED

SCHWARZ NEGRO

Model RK100PK and RK100PKW Microex®

Preampler Kit User Guide

27A3252 (Rev. 1) Printed in U.S.A.

INSTALLATION - RK100PK (BLACK), RK100PKW (WHITE)

The RK100PK and RK100PKW preamp comes assembled for

use with microphones using a miniature 4-pin connector. To wire a

microphone cable directly to the preamp, follow these instructions:

Turn screw (A) counter-clockwise until it recedes below

the case.

Remove the cap (C) by removing the set screw (B) with

the provided hex wrench (.05 in.).

FIGURE 1

Push the circuit board out from the case interior to expose

the black and red wires (D).

Unsolder the wires from the circuit board (E).

FIGURE 2

Insert the rubber ex relief (G) into the cap (C) and feed

through the microphone cabling.

Note: You will need to reuse the rubber ex relief from your old

preamp. If the rubber ex relief is unavailable, please contact the

Shure Service Department.

FIGURE 3

Solder the wires directly back onto the circuit board.

Match wires as marked on the circuit board using the fol-

lowing key:

R = RED

B = BLACK

S = (GROUND) SHIELD

FIGURE 4

Push the circuit board back into the case, making sure

that the set screw (A) is lined up with the screw hole in

the side of the case (if the circuit board does not go in

all the way, twist it slightly until the screw and hole are

aligned). Raise the set screw (A) by turning clockwise

so that the preamplier is held securely in place. Screw

on the cap (C). Do not use the set screw with the cap.

SHURE Incorporated http://www.shure.com

United States, Canada, Latin America, Caribbean:

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446

Europe, Middle East, Africa:

Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414

Asia, Pacific:

Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

Ce manuel convient aux modèles suivants

Autres manuels Shure Amplificateur

Shure

Shure SHA900 Manuel utilisateur

Shure

Shure UA834 Manuel utilisateur

Shure

Shure Microflex RK100PK Manuel utilisateur

Shure

Shure UA834WB Manuel utilisateur

Shure

Shure UA834 Manuel utilisateur

Shure

Shure WA400 Manuel utilisateur

Shure

Shure SHA900 Manuel utilisateur

Shure

Shure M64A Manuel utilisateur

Shure

Shure (R) FP22 Manuel utilisateur

Shure

Shure SHA900 Manuel utilisateur

Shure

Shure FP23 Manuel utilisateur

Shure

Shure Solo-Phone SA-1F Manuel utilisateur

Shure

Shure SOLO-PHONE SA-1 Manuel utilisateur

Shure

Shure SR10 Manuel d'utilisation

Shure

Shure M267 Manuel utilisateur

Shure

Shure A900-PM-38IN Manuel utilisateur

Shure

Shure MX1BP Manuel utilisateur

Shure

Shure UA830 Manuel utilisateur

Shure

Shure SR109 Manuel d'utilisation

Shure

Shure UA830 Manuel utilisateur

Shure

Shure UA845 Manuel utilisateur

Shure

Shure HTS50SPA Manuel utilisateur

Shure

Shure RK183PK Manuel utilisateur

Shure

Shure ILP-1 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur