Ⅵ. Test Report
S/N Test Item
Quantity
Test Requirements/Standards Test Steps
Test Results
Structural
component
inspection
1. A professional test technican
inspects the hardware and structural
parts of the device according to the
inspection requirements/standards;
2. During the inspection, the device
should not have any problems other
than the standards; inspection ended
Packaging
inspection
The surface of the packaging should be
clean and tidy without obvious defects,
such as concave and convex distortions,
scratches, cracks, deformations and
burrs. The surface coating should not
blister, crack, or fall off. The text, graphics
and symbols on the outer box, and in the
Instruction Manual, etc. should be clear
and feature correct indications
1. Before packaging the device, a
professional test technician should
inspect the surface, outer box,
Instruction Manual, etc. of the device
according to the inspection
requirements/standards;
2. During the inspection, the device
should not have any problems other
than the standards; inspection ended
5
6
1
1
PASS
PASS
Metal parts should be free from rust and
other mechanical damage. The color of
the surface coating should not have any
obvious color discrepancy. The operating
switches and buttons should work flexibly
and reliably, and parts should be fastened
and not loose. There should be no
obvious installation gaps. The complete
device should have sufficient mechanical
stability
Note: The above test requirements/standards are the internal test standards of the commercial display advertising machine
industry.
ISED Statement
English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt R S S(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux RSS exemptés de
licence d'Innovation, Sciences et Développement économique Canada.
L'exploitation est soumise aux deux conditions suivantes :
(1) Cet appareil ne doit pas provoquer d'interférences.
(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement
indésirable de l'appareil.
l'appareil numérique du ciem conforme canadien peut - 3 (b) / nmb - 3 (b).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with R S S 102
RF exposure, users can obtain Canadian Information on R F exposure and compliance.
cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité
avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux
champs rf et la conformité.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
Cet équipement est conforme aux limites d'exposition aux rayonnements du Canada établies pour un environnement non
contrôlé.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party.
Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded
interface cables when connecting to computer or peripheral devices).
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with F C C Radiation exposure limits set forth for uncontrolled enviroment. This equipment should
be installed and operated withminimum distance 20cm between the radiator and your body.
