Sharp XE-A147-BK Mode d’emploi

XEA147BK and XEA147WH Frequently Asked Questions Page 1 of 21

XEA147BK And XEA147WH Frequently Asked Questions.

XEA147BK and XEA147WH Frequently Asked Questions Page 2 of 21

How do I prepare my XEA147 for set-up?

Take the XEA147 out of its box, remove the packing materials. Place the XEA147 on a flat stable surface,

close to a power outlet. Also insure it will not be exposed to direct sunlight, and is away from water (taps,

sinks, etc).

How do I clear the XEA147 to ready it for programming?

It is very important that you “initialise” the XEA147 correctly once you have removed it from the box, and

are ready to start programming. If you do not “initialise” the XEA147, it might not work correctly.

1. Insert the Mode key into the mode switch and turn it to the REG position.

2. Plug the AC adapter connector into the AC adapter jack, then plug the AC adapter into the wall

outlet.

This must be done without the batteries installed. If you have installed batteries; be sure to remove

them before you start this procedure.

After a few seconds, the register display should look as indicated below.

The register is initialised.

Note: This register does not have a sound function. No beep sound will be made when pressing

keys, this is normal, and is not a malfunction.

If the above steps do not happen as described, the initialisation has not been successful. If this is the

case: disconnect the register from the AC outlet, wait at least one minute, and then try again.

If there were any data from a previous programming attempt, they would have been cleared

XEA147BK and XEA147WH Frequently Asked Questions Page 3 of 21

How to install the batteries, and why should I do so?

The XEA147 uses 3 x AA size batteries to hold its preset, and sales data in memory when it is switched

off. If you do not install 3 x AA size batteries; the XEA147 will be cleared of all preset, and sales data

when it is turned off.

1. Lift the printer cover up and forward, and detach it. Be careful of the paper cutter to avoid cutting

yourself.

2. Open the battery compartment cover next to the paper roll cradle.

3. Install 3 alkaline AA size batteries.

4. When the batteries are properly installed the “ ” message on the display will disappear.

Note: If you press a key by mistake, an error symbol “PPPPPPPPPP” might be displayed. Press

CL to clear the symbol after installing the paper rolls. (see next question).

5. Close the battery compartment cover.

A set of new alkaline batteries once installed will keep the memory for up to one year without power.

Please see the question on how to replace the batteries for details on when and how to replace the batteries.

If the unit is not used for some months, you might not get any warning when you turn it on that the

batteries have failed. In this instance, the XEA147 will initialise itself.

XEA147BK and XEA147WH Frequently Asked Questions Page 4 of 21

What sort of paper roll do I use, and how do I install it?

The XEA147 uses a thermally sensitised paper roll which is: 57mm wide. Its maximum diameter should

be no more than 80mm.

1. Pull the printer cover forward and detach it. The paper cutter is mounted on the printer cover, be

careful not to cut yourself.

2. Lift up the print roller arm.

XEA147BK and XEA147WH Frequently Asked Questions Page 5 of 21

3. Set the paper roll in the paper roll cradle as shown in the diagram below.

Note: Before placing a new paper roll in the paper roll cradle, cut off the pasted (taped), part of the

paper and confirm that the cut end of the paper is straight.

XEA147BK and XEA147WH Frequently Asked Questions Page 6 of 21

4. Feed the end of the paper along with the paper positioning guides as shown in the diagram below.

5. While holding the paper down, slowly close the print roller arm, and push down the arm until your

hear a click locking the arm.

6. Cut off the excess paper and replace the printer cover.

7. Press the key to make sure the paper end comes out of the printer cover and clean paper appears.

If the paper end does not come out. Open the printer cover, and pass the paper end between the

paper cutter and the paper guide of the printer cover, and replace the cover.

XEA147BK and XEA147WH Frequently Asked Questions Page 7 of 21

How do I set the time and date?

1. Set the mode key to the Z/PGM position.

2. Enter the time as a four digit number. Use the 24 hour format. For example

2:30pm would be entered as 1 4 3 0

3. Press the #/TM/ST key

4. Enter the date as six digits using the day-month-year format. For example

5. 7

of December 2013 would be entered as 0 7 1 2 1 3

6. Press the #/TM/ST key

How do I set a 10% GST rate?

1. Set the mode key to the Z/PGM position

2. Enter:

#/TM/ST 9 /RCPT SW 1 /RCPT SW 1 0 0 0 0 0 #/TM/ST TL/AT/NS

XEA147BK and XEA147WH Frequently Asked Questions Page 8 of 21

How do I set a Department as taxable or not taxable?

1. Set the mode key to the Z/PGM position

2. To make a department taxable, enter:

#/TM/ST -2--0-/RCPT SW 1 DEPT KEY TL/AT/NS

For example to make department 1 taxable enter:

#/TM/ST -2--0-/RCPT SW 1 1

TL/AT/NS

For example to make department 1 non-taxable enter:

#/TM/ST -2--0-/RCPT SW 0 1

TL/AT/NS

Press _SHIFT then the department key for departments 5 to 8

For example to make department 5 taxable enter:

#/TM/ST -2--0-/RCPT SW 1 SHIFT 1

TL/AT/NS

For example to make department 5 taxable enter:

#/TM/ST -2--0-/RCPT SW 0 SHIFT 1

TL/AT/NS

Enter 1 before you press the department key to make the department taxable

Enter 0 before you press the department key to make the department non-taxable.

XEA147BK and XEA147WH Frequently Asked Questions Page 9 of 21

How do I set the letters GST to print on the receipt?

1. Set the mode key to the Z/PGM position

2. Enter: #/TM/ST -1--0--3-_/RCPT/SW_7 _/RCPT/SW

-6-1

-8-2

-9-2

#/TM/ST TL/AT/NS

You can enter characters with the department and function keys. You will see the

letters of the Alphabet that a key covers in the bottom right hand corner of the key.

You can also enter text using 3 digit codes. Please refer to the full instruction manual (pages 43 -44)

for details. The character table for using the department and function keys is shown below.

XEA147BK and XEA147WH Frequently Asked Questions Page 10 of 21

How do I set the $ symbol to print on receipts?

1. Set the mode key to the Z/PGM position

2. Enter:

#/TM/ST 8 5 _/RCPT/SW 0 3 2 _00_0 3 2 _00_0 3 2 _00_

0 3 6 _00_#/TM/ST TL/AT/NS

How do I make cash sales amounts round to the nearest 5 cents?

3. Set the mode key to the Z/PGM position

4. Enter:

#/TM/ST 6 7 _/RCPT/SW 1 1 8 _2_1 0 1 0 #/TM/ST TL/AT/NS

How do I change the power save (screen off) time?

5. Set the mode key to the Z/PGM position

6. Enter:

#/TM/ST 1 0 _/RCPT/SW 0 0 #/TM/ST TL/AT/NS

This will set the power save time to 100 minutes. This is the maximum time which can be set before the

power save mode activates. The default time is 30 minutes.

Ce manuel convient aux modèles suivants

Autres manuels Sharp Caisse

Sharp

Sharp XE-A507 Guide de configuration

Sharp

Sharp XEA102 - Cash Register Manuel utilisateur

Sharp

Sharp XE-A202 - Electronic Cash Register Manuel utilisateur

Sharp

Sharp XEA102 - Cash Register Manuel utilisateur

Sharp

Sharp ER-A570 Manuel du propriétaire

Sharp

Sharp ER-A520 Manuel du propriétaire

Sharp

Sharp CS-4194H Manuel utilisateur

Sharp

Sharp ER-A520 Guide produit

Sharp

Sharp ER-2386S Manuel utilisateur

Sharp

Sharp XE-A213 Manuel utilisateur

Sharp

Sharp ER-1910 Manuel utilisateur

Sharp

Sharp XE-A505 - Cash Register, Thermal Printing Manuel utilisateur

Sharp

Sharp XE-A201 Manuel utilisateur

Sharp

Sharp ER-A410 Manuel utilisateur

Sharp

Sharp XE-A207W Manuel d'utilisation et d'entretien

Sharp

Sharp XE-A407 Manuel utilisateur

Sharp

Sharp ER-2386S Manuel utilisateur

Sharp

Sharp TINSZ2600RCZZ Manuel utilisateur

Sharp

Sharp XE-A101 Manuel utilisateur

Sharp

Sharp ER-A440 Manuel utilisateur

Sharp

Sharp er-3100 Manuel utilisateur

Sharp

Sharp ER-A570 Manuel utilisateur

Sharp

Sharp XE-A206 Manuel utilisateur

Sharp

Sharp ER-A310 Manuel utilisateur

Manuels Caisse populaires d'autres marques

Royal

Royal 480nt Manuel utilisateur

Olivetti

Olivetti ECR 8200 S Manuel utilisateur

TEC

TEC TEC FS-3600 Manuel utilisateur

Integrated System Laboratory

Integrated System Laboratory ISL 4006 Manuel utilisateur

Sam4s

Sam4s ER-380 Guide de dépannage

Samsung

Samsung ER 5215 Manuel utilisateur

Toast

Toast Toast Manuel utilisateur

TEC

TEC MA-600-1 series Manuel utilisateur

QUORION

QUORION CR 1200 Manuel utilisateur

Olivetti

Olivetti ECR 7700 LD eco Plus Manuel utilisateur

TEC

TEC TEC MA-1060 Manuel utilisateur

Casio

Casio PCR-408 Instructions de montage

ELCOM

ELCOM Euro-2100TE Manuel utilisateur

American Changer

American Changer CLASSIC Series Manuel utilisateur

Sam4s

Sam4s ER-180 Manuel utilisateur

Sam4s

Sam4s ER-5100? SERIES Manuel utilisateur

Casio

Casio PCR-T273 Manuel utilisateur

Casio

Casio PCR-T2100 Manuel utilisateur