Shannon DA Manuel utilisateur

Turfschipper 11

2292 JC Wateringen

The Netherlands

Phone:+31(0)174-225240

Email: info@shannonmachines.com

Website:www.plasticbending.com

VAT: NL818676954B01

User instructions for the plastics

and acrylic sheet bending machine

DA INSTRUCTION MANUAL 
 
2 
 
INDEX 
 
 
1. INTRODUCTION ............................................................................................................2 
1.1. EC DECLARATION OF CONFORMITY......................................................................2 
1.2. DIRECTIVES APPLIED TO THE MACHINE.............................................................................3 
2. TECHNICAL DATA........................................................................................................4 
3. SAFETY MEASURES .....................................................................................................5 
3.2. WORKING SAFETY WARNINGS ...............................................................................5 
LIGHTING OF WORK ENVIRONMENT............................................................................6 
3.3. SAFETY WARNINGS...................................................................................................7 
4. PANEL CONTROL INTRODUCTION............................................................................7 
5. METHOD FOR MACHINE BASIC PREPARATION....................................................12 
 
 
 
1. INTRODUCTION 
1.1. EC DECLARATION OF CONFORMITY 
We, 
 WORLDMAQ-3 S.L. 
Ctra. Molí del Castell, s/n 
08610 AVIÀ (Barcelona) 
Spain 
 
 
declare under our unique responsibility, that the machine: 

DA INSTRUCTION MANUAL

Brand: BERMAQ

Type: Plastics and Acrylic Sheet Bending Machine

Model: DA

follows the following Rules:

-Direction of Machine 2006/42/CE..

-Direction of Low Tension 2006/95/CEE.

-Direction of Electromagnetic Compatibility 2004/108/CE.

1.2. DIRECTIVES APPLIED TO THE MACHINE

MACHINERY DIRECTIVE: 2006/42/CE (FORMERLY 89/392/EEC REVISED BY

98/37/CE AND 93/68/EEC)

This directive applies to all machines and to all safety components. A machine is an assembly

of linked parts or components, at least one of which moves. It is generally applied that a "machine" must

perform a specific function. A comprehensive list of hazards is defined in Annex I of this directive. The

Machinery Directive requires that a hazard analysis be made, preformed, and documented. It also

requires the machine to be evaluated for electrical safety to the harmonized product safety standard.

Typical products are evaluated using the following standards:

•UNE-EN ISO 12100:2012: Safety of Machinery - Principles for Risk Assessment.

•UNE-EN 60204-1:2007: Safety of Machinery - General Requirements.

LOW VOLTAGE DIRECTIVE (LVD): 2006/95/CEE (REVISED BY 93/68/EEC)

The Low Voltage Directive sets essential requirements for the product safety of electrotechnical

products. This directive requires electronic products to be tested to the Harmonized Product Safety

Standard for your product type. The Low Voltage Directive does not consist only of technical

DA INSTRUCTION MANUAL

requirements. This directive requires the producer to keep a file of all relevant data (Technical

Document File), to officially state the conformity of the product (Declaration of Conformity), to inform

the users about safe use/installation/maintenance, and to mark the product with a CE Marking.

Typically products are evaluated using one of the following standards:

•EN 60950-1: Safety of Information Technology Equipment.

•EN 61010-1: Safety requirements for electrical equipment for measurement, control, and

laboratory use.

ELECTROMAGNETIC COMPATIBILITY (EMC) - 2004/108/CE

The electromagnetic compatibility Directive sets the essential requirements for electrical and

electronic equipment that may disturb or even be disturbed by other equipment. This Directive relates

to all electrical or electronic equipment.

The EMC Directive cameinto force on 1st January 2007 and it became a legal obligation on1st January

2009. This means that from that moment on, no more equipment may be placed on the market or put

into operation without the CE Marking. The CE Marking may be omitted from equipment that was

already placed on the market before that date. It will very rarely be the case that only the EMC Directive

is applicable to a product. With electrically driven machines, for example, a combination of the

Machinery Directive, the Low voltage Directive and the EMC Directive will often apply.

2. TECHNICAL DATA

DIMENSIONAL SPECIFICATIONS

Outer dimensions: AxBxC

2950 x 1100 x 1920 mm

Weight

160 kg.

BENDING SPECIFICATIONS

Conveyor belt speed

1m/min-

15m/min

Maximum width unfolded piece

595mm

Maximum lenght piece

345mm

Minimum/Máximum bending size

30 - 260mm

Bending Angle

90º - 145º

DA INSTRUCTION MANUAL

ELECTRICAL SPECIFICATIONS

Tension

230 V 1PH+N+T

Frequency

50/60 Hz

Full power capacity

1,8 kW

Intensity

8 A

3. SAFETY MEASURES

WORLDMAQ-3 S.L. In compliance with EEC Directive 2006/42/CE and in

accordance with European Union standards, this machine has been adapted to all safety

precautions.

3.2. WORKING SAFETY WARNINGS

•The operator should be instructed and of sound mind to operate this type of machine.

•Before starting the machine, be sure that there are no visible obstacles that would create

any danger, such as any materials that are in the way of the carriage travel or leaning

against the machine, etc...

DA INSTRUCTION MANUAL

•Do not handle any electrical elements when another operator is working at the machine.

•Do not change or modify the electro equipment since this could cause a malfunction and

lead to accidents.

•Maintain all safeguards in the proper position. Do not handle the electrical equipment

employed to check such safeguards.

•Check periodically the mechanical components and the tube integrity.

•Always use the appropriate clothing for working on this machine. Avoid long, wide

sleeves, shirttails and clothes which do not fit tightly. It is recommended one's sleeves

always be rolled up. Do not manipulate anything inside the electrical boxes without

switching off the main switch.

•Do not work on the machine while wearing personal articles or objects such as

wristwatches, bracelets, necklaces, etc. which may become stuck in the machine at some

time.

•To work on the electric panel, the main switch should be in the OFF position. (Only

instructed operators and technicians).

LIGHTING OF WORK ENVIRONMENT

The lack of suitable lighting for the type of operations foreseen endangers personal safety. The

work area should be lighted in accordance with ISO 8995-89 standards (Lighting of work

premises) so that there are no areas in shadow or glaring lights.

ATTENTION!

The manufacturer is released from civil or criminal liability if non-authorized

changes or substitutions are made on one or more parts of the machine; if

accessories, tools or materials different from those recommended for the machine are

employed; or if the machine forms part of a complex system and performs work not

compatible with its specific characteristics.

DA INSTRUCTION MANUAL

3.3. SAFETY WARNINGS

MACHINERY DIRECTIVE 2006/42/CE state the following definitions:

•DANGER ZONE: All those areas within and/or near a machine in which the presence of

a person implies a risk to his safety or health.

•EXPOSED PERSON: All those persons who are totally or partially in a danger zone.

•OPERATOR: Person in charge of installing, starting up, adjusting, maintaining, cleaning,

repairing and transporting the machine.

¡WARNING!

All operators who work with the machine must know about the safety regulations.

4. PANEL CONTROL INTRODUCTION

1. Main power supply switch.

2. Adjustment of conveyor belt parameters.

2.1. Speed adjustment of conveyor belt.

The speed is adjusted through the round regulator and the display shows the current

frequency of the conveyor belt motor.

DA INSTRUCTION MANUAL

2.2. Start the conveyor belt.

The green button will start the conveyor belt.

2.3. Stop the conveyor belt.

The red button will stop the conveyor belt.

2.4. Emergency stop.

The machine stops completely.

2.5. Adjustment of the elapsed time.

Inside the electrical cabinet there is a relay to adjust the elapsed time since the piece

enters until it leaves the machine. After this time, if the sensor at the end of the

machine does not detect the piece, the signal tower will show a red light and the

machine will stop completely, since there has been a piece jam.

To restart the machine push the stop feeding cycle button to start the conveyor belt

(3.5).

To adjust the elapsed to the needs of each piece, please follow the instructions:

- The upper regulator is for setting the total elapsed time.

- The middle regulator is for adjusting the percent of the total elapsed time

selected on the upper regulator (number 10 means 100%, 5 means 50%,

etc.)

- The last regulator must not be manipulated. In case of accidental

manipulation, please turn the regulator to A position.

Example. The total elapsed time desired is 15 seconds. To adjust the relay proceed as

following:

- Adjust the upper regulator at 30s.

DA INSTRUCTION MANUAL

- Adjust the middle regulator at 5.

- This combination means that the elapsed time will be 15s (50% of 30s =

15s)

3. Adjustment of feeding cycle parameters.

3.1. Up/down feeder tray

To up and down the feeder tray. It allows loading the pieces on the tray.

3.2. Feeder tray pressure adjustment

To adjust the pressure of the feeder tray when it is feeding. The recommended adjust

is at least 3 bar. It may be necessary to increase this value according to the quantity

and weight of the pieces loaded on the tray.

3.3. Piece feeder pressure adjustment

To adjust the pressure of the piece feeder. The recommended adjustment is 6 bar.

3.4. Start feeding cycle

To start the feeding cycle

Once the conveyor belt is turned on, is possible to start and stop the feeding cycle.

Notice that is not possible to start de feeding cycle if the conveyor belt is turned off.

There is an extra start/stop feeding cycle button in the back part of the machine. The

operation of this button is the same that the one in the front part of the machine.

Once the preselected amount is completed the feeder will stop automatically. To start a new

cycle press once the start feeding cycle button.

DA INSTRUCTION MANUAL

3.5. Stop feeding cycle

To stop the feeding cycle

Also to restart the machine

3.6. Count controller

Adjust the desired amount of pieces to feed by pressing the button according to the

number units. The amount will be shown in the lower part of the display.

The total amount of pieces counted will be showed in the upper part of the display.

You can reset the counter by pressing RST button.

4. Adjustment of temperature parameters.

4.1. Left/right resistance temperature controller.

This is used to adjust the resistance temperature.

Table des matières

Manuels Équipement industriel populaires d'autres marques

ABB

ABB Unifix AD Manuel

Mark 7

Mark 7 Evolution Manuel utilisateur

Husky

Husky HyPET Manuel utilisateur

bora

bora PM-1800 Manuel utilisateur

Grizzly

Grizzly T32428 Manuel utilisateur

Siemens

Siemens 8MF1 Series Manuel utilisateur

ABB

ABB HT610965 Manuel utilisateur

ABB

ABB SafeLink Manuel utilisateur

Phoenix

Phoenix PHX-150 Manuel utilisateur

ABB

ABB A165-L32 Manuel utilisateur

ABB

ABB HT842936 Manuel utilisateur

Rioned

Rioned UrbanJet Manuel utilisateur

Hermetica

Hermetica 10 Series Manuel utilisateur

HORNER

HORNER OEE Solution Manuel utilisateur

Hammerhead

Hammerhead HG375 Manuel utilisateur

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instructions d'utilisation

ABB

ABB HT566657 Manuel utilisateur

Webasto

Webasto GSE CAN Manuel utilisateur