SG Namsen 600 Manuel utilisateur
Installation Manual
For Model 600
smoke containment systems from Smoke Guard
Smoke Guard Technical Services: 1-800-215-6138
Installation Manual
For Model 600
smoke containment systems from Smoke Guard
Smoke Guard Technical Services: 1-800-215-6138
Doc 601, Rev 24 for use with housing Rev 3
2
Table of Contents
Introduction................................................................................................................ 4
Materials .................................................................................................................... 5
Preparation ................................................................................................................ 7
Installing the Mounting Plate...................................................................................... 9
Installing the Housing................................................................................................11
Installing Auxiliary Rails.............................................................................................13
Installing the Curtain .................................................................................................17
Installing the Curtain Rewind Switch .........................................................................21
Re-attaching the Housing Door.................................................................................22
Calibrating the System..............................................................................................23
Testing the Installation ..............................................................................................24
Securing the curtain..................................................................................................25
Preparing the Unit for the Electrical Contractor and Alarm Technician ......................26
Appendix A: Suggested Mounting Plate Anchors ......................................................27
Appendix B: Wiring Diagram .....................................................................................28
Appendix C: Troubleshooting a System Fault............................................................29
3
Introduction
As a factory recognized installer for the Model 600 Smoke Guard System, read this
installation manual to become familiar with all installation tasks before beginning. This
manual tells you what you need to know about installing the Model 600 smoke
containment system from Smoke Guard Corporation.
°About the Model 600
°About installation of the Model 600
About the Model 600
The Model 600 is a smoke-containment system. A curtain drops from a housing to the
floor, creating a seal around the elevator opening that prevents smoke from traveling
through the elevator shaft to other floors. The curtain drops when the smoke detector to
which the housing is wired goes into alarm.
For information about the Model 600 and building codes, see the Model 600 Operation
and Maintenance Manual.
About installation of the Model 600
Installers of the Model 600 require a moderate amount of construction experience.
Specifically, installation requires tools and materials listed on page 5 and experience
with the following:
°drilling through metal, sheet rock, and wall studs
°working with fasteners appropriate for the wall and stud materials
°pop-riveting
°terminating low voltage wires
°understanding open and closed contacts
°reading one line wiring diagrams
°how to use a voltage meter
Installation of the Model 600 occurs:
°after installation of the elevator frame
°after dry wall is mounted around elevator frame
°prior to ceiling installation
4
Materials
The materials that you require to install a Smoke Guard System include tools and
materials that you provide as well as the components of the product provided by Smoke
Guard.
Components and materials furnished by Smoke Guard
mounting plate,
attached to
housing for
shipping
2 rail mounting
channels
2 auxiliary rails
(rails required for most installations)
end-of-line diode in junction box
on left side of housing
Per project
installation
materials:
Installation
Overview,
Wiring Guide,
spare end-of-
line diode,
door key
roll of Kapton®tape
housing
curtain mounting
J-clips (not included
in shipment,
available from
Smoke Guard)
bag of
fasteners
motor jogger
(not included in
shipment,
available from
Smokde Guard)
curtain
assembly,
ships
inside
housing
5
Tools and materials furnished by the installer
In addition to the components and materials supplied by Smoke Guard, installation
requires the following tools and materials:
6
Preparation
Prior to installing the Smoke Guard system, the general contractor prepares the site for
installation.
°Verify housing clearance
°Verify curtain assembly clearance
°Remove housing door
Verify housing clearance
For each housing, the general contractor provides a clearance above the elevator:
°unobstructed, wall plumb, with no distortions
°no more than 10 feet from the floor to the bottom of the housing
°at least 10 inches tall
°at least 12 inches deep
°at least 2 inches wider than the housing allowing the curtain to be centered
over the door
°mounting height marked with a chalk line
°devoid of ceiling and grid in housing area
°with backing extending the full width and height of clearance, behind new wall
construction or over existing wall construction
distance from bottom
of housing to floor not
to exceed 10 feet
ceiling height marked
2 inches wider
than housing
housing clearance
dimensions, centered
over elevator frame
10 inches
7
Verify curtain assembly clearance
General contractor provides clearance on landing side of elevator:
°extending from the bottom of the housing to the floor along full curtain
assembly width
°centered over the hoistway frame
°unobstructed, wall plumb, with no distortions
°free of all obstructions and projections that exceed the housing return within the
full width extending from the bottom of housing to the floor, including elevator
position indicators, signs, and hall call stations
°includes clearance for door swing
°with 2 inch wide backing for auxiliary rail backers extending the full height,
behind new wall construction or over existing wall construction
Remove Housing Door
Installation will be easier if you remove the housing door before you begin.
To remove the housing door:
1. Remove screws holding door rod on one side of the housing door.
2. Pull rod out enough to remove the door.
8
Autres manuels pour Namsen 600
1
Table des matières
