SewingMachinesPlus QF00007-12 Manuel utilisateur
King Quilter Frame Assembly 1
King Quilter Frame
NOVEMBER 2018
Assembly Instructions
Table of Contents
Parts List ..........................................page 2
Preparation: Batting Bar Bracket Assembly, Do this First! ....page 7
Step 1: End Leg Assembly..............................page 8
Step 2: Table Assembly ...............................page 14
Step 3: Center Leg Assembly ...........................page 15
Step 4: End Leg to Table Assembly ......................page 17
Step 5: Precision-Glide Track Assembly .................. page 22
Step 6: Front Pole Carrier / Rear Pole Carrier Arm Assembly . page 25
Step 7: Bungee Cleat Assembly .........................page 26
Step 8: Leveling the Frame.............................page 27
Step 9: Pole Assembly ................................page 28
Step 10: Adding Pole Ends .............................page 29
Step 11: Pole to Frame Assembly ....................... page 31
Step 12: Rubber End Cap Assembly ......................page 32
Step 13: Bungee Clamp Assembly .......................page 33
Step 14: Hook and Loop Strips on Poles Assembly ..........page 34
Step 15: Attach Leaders ..............................page 35
#QF00007-12 and QF00007-10
2 King Quilter Frame Assembly
Table Splice Brace (4)
Part# QF09318-05
BOX3
Four Foot Table Section
(3) For 12’ frame,
(2) for 10’ Frame
Part# QF00007-301
BOX 1 & 4
Track Support Coupler (4)
Part# QF09318-03
BOX 3
Bungee Clamp (4)
Part# QF09318-110
BOX 3
4-foot Pole Section
Fifteen come with 12’ frame and ten come with
10’ frame.
Part# QF0007-701
BOX 2 & 4
2-Foot Coupler (10)
Part# QF09318-702
BOX 2
Front Gusset Bracket (2)
Part# QF00007-413
BOX 3
12-foot Black Plastic Track (4)
Part# QF09318-04
BOX 3
4 Foot Track Support Section
(6) For 12’ frame, (4) for 10’ frame
Part# QF09318-02
BOX 1 & 4
SMP QF00007-12 and QF00007-10 Frame Parts List
Two Foot Table Section (1) with
10’ Frame Only
Part# QF00007-302
BOX 4
2-foot Pole Section
Five come with 10’ frame only,
None come with 12’ frame
Part# QF0007-703
BOX 4
2 Foot Track Support Section
(2) For 10’ frame only, (0) come with 12’ Frame
Part# QF09318-02
BOX 4
Leaders - No Image
11’ Leaders for 12’ Frame (1)
Part# QF09580
or
9.5’ Leaders for 10’ Frame (1)
Part# QF09851
BOX 4
King Quilter Frame Assembly 3
SMP QF00007-12 and QF00007-10 Frame Parts List
Upper Beam Left Hand Side Leg (1)
QF00007-503
BOX 1
Upper Beam Right Hand Side Leg (1)
QF00007-403
BOX 1
Upright Beam Both Sides (2)
QF00007-402
BOX 1
Lower Beam (Both Sides) (2)
QF00007-401
BOX 1
Inside Left Inside Right
Rear Leg Lower (Both Sides) (2)
QF00007-409
BOX 3
Rear Leg Upper Left (1)
QF00007-508
BOX 3
Rear Leg Upper Right (1)
QF00007-408
BOX 3
Inside Left Inside Right
4 King Quilter Frame Assembly
SMP QF00007-12 and QF00007-10 Frame Parts List
Lower Gusset Bracket (1 per side=2 total)
QF00007-406
BOX 3
Upper Gusset Bracket (1 per side=2 total)
QF00007-407
BOX 3
Outer Side Bracket Left (2 per side= 4 total)
QF00007-405
BOX 3
Outer Side Bracket Right (2 per side=4 total)
QF00007-404
BOX 3
Pole Cradle (3)
QF11038
BOX 3
Screw, M4x18SKC ZN (9)
QF10870
BOX 3
Washer, M4x10 Flat ZN (9)
QF00007-417
BOX 3
King Quilter Frame Assembly 5
SMP QF00007-12 and QF00007-10 Frame Parts List
Front Left Pole Carrier (1)
QF00007-511
BOX 3
Front Right Pole Carrier (1)
QF00007-411
BOX 3
Rear Pole Carrier Arm (2)
QF00007-410
BOX 3
Upper Middle Leg
(2) for 12’ frame, (1) for 10’ frame
QF005300-602
BOX 3
Lower Middle Leg
(2) for 12’ frame, (1) for 10’ frame
QF05300-601
BOX 3
Batting Bar Bracket (2)
QF00007-414
BOX 3
Bungee Cleat Bar (2)
QF00007-412
BOX 3
6 King Quilter Frame Assembly
SMP QF00007-12 and QF00007-10 Frame Parts List
M8 Lock Nut (1)
Part# QF09318-08
BOX 3
M8 Flat Washer (1)
Part# QF09318-702
BOX 3
17/13/16mm Wrench (1)
Part# QF09318-114
BOX 3
5mm Allen Wrench (1)
Part# QF09318-113
BOX 3
Ratchet Left Hand (1)
Part# QF11035
BOX 3
Ratchet Right Hand (2)
Part# QF11034
BOX 3
Leveling Foot (8)
Part# QF09318-108
BOX 3
Rubber End Cap (2)
Part# QF09318-716
BOX 3
4mm Allen Wrench (1)
Part# QF09318-112
BOX 3
Button Head Cap
Screw M5 x 8mm
(SBHCS) (24 total)
Part# QF09318-304
BOX 3
Large washer head
screw M6 x 12mm
(26 total)
Part# QF09318-303
BOX 3
Hand Wheel Assembly (1)
Part# QF09325
BOX 3
HAND WHEEL ASSY
QF09318-720
SHORT BOLT RATCHET WHEEL
QF09318-730 QF09318-730
LONG BOLT RATCHET WHEEL
Spg Lded Idler End Cap (4)
Part# QF11037
BOX 3
HAND WHEEL ASSY
QF09318-720
SHORT BOLT RATCHET WHEEL
QF09318-730 QF09318-730
LONG BOLT RATCHET WHEEL
HAND WHEEL ASSY
QF09318-720
SHORT BOLT RATCHET WHEEL
QF09318-730 QF09318-730
LONG BOLT RATCHET WHEEL
HAND WHEEL ASSY
QF09318-720
SHORT BOLT RATCHET WHEEL
QF09318-730 QF09318-730
LONG BOLT RATCHET WHEEL
3mm Allen Wrench (1)
Part# QF09318-111
BOX 3
QF09318-103
BUNGEE HOLDER BUNGEE HOLDER COVER
QF09318-104
BUNGEE HOLDER SPACER
QF09318-103
RATCHET STOP
QF09318-203
RATCHET STOP HOLDER
QF09318-205
RATCHET STOP BUSHING
QF09318-201
CONNECTOR BOLT
QF09318-204
QF09318-202
RATCHET STOP MOUNT
RAIL BEARING SNAP
QF09318-105
RAIL BEARING SNAP COVER
QF09318-106
Fig. 10-2
QF09318-105
QF09318-703
OUTSIDE POLE END V-GROOVE BEARING
QF09318-705 QF09318-713
HAND WHEEL COLLAR
QF09318-714
STEEL SNAPPING BUTTON/LOCKING CLIP
LEVELING FOOT
Hand Wheel Insert (1)
May be pre-assembled
with Hand Wheel.
Part# QF09318-713
BOX 3
QF09318-103
BUNGEE HOLDER BUNGEE HOLDER COVER
QF09318-104
BUNGEE HOLDER SPACER
QF09318-103
RATCHET STOP
QF09318-203
RATCHET STOP HOLDER
QF09318-205
RATCHET STOP BUSHING
QF09318-201
CONNECTOR BOLT
QF09318-204
QF09318-202
RATCHET STOP MOUNT
RAIL BEARING SNAP
QF09318-105
RAIL BEARING SNAP COVER
QF09318-106
Fig. 10-2
QF09318-105
QF09318-703
OUTSIDE POLE END V-GROOVE BEARING
QF09318-705 QF09318-713
HAND WHEEL COLLAR
QF09318-714
STEEL SNAPPING BUTTON/LOCKING CLIP
LEVELING FOOT
Ratchet Idler End Cap (3)
Part# QF11036
BOX 3
Screw M8 x 1.25 x 16 SBHCS (98)
Part# QF09318-07
BOX 3
Large washer head
screw M6 x 50mm
(SBHCS) (4 total)
Part# QF00007-200
BOX 3
Ratchet Thumb Shifter
(3)
Part# QF11023
BOX 3
King Quilter Frame Assembly 7
Preparation: Batting Bar Brackets
Parts Needed
2 - upright beams
2 - batting bar brackets
2 - screws, M8 x 16mm SBHCS
Tools Required
5mm Allen wrench (provided)
Prep-1: Insert an M8 x 16mm SBCHS
into the batting bar bracket on the left
side of the frame.
Prep-2: Slide the bracket towards the
center of the frame until it touches the
leg and there is no gap. Fully tighten
the screw with the M5 Allen tool
provided.
Prep-3: Repeat the process for the
batting bar bracket on the right side of
the frame.
left side right sideinside view of
upright beam
Do this Preparation rst!
8 King Quilter Frame Assembly
Parts Needed
1 - left rear leg upper
1 - right rear leg upper
2 - rear leg lower
2 - lower leg beam
1 - upper beam left hand side leg
1 - upper beam right hand side leg
2 - upright leg beam
4 - outer side bracket right
4 - outer side bracket left
2 - lower gusset bracket
2 - upper gusset bracket
4 - leveling feet
58 - screw M8 x 16mm SBHCS
8 - screw M6x12 SH ange
Tools Required
5mm Allen wrench (provided)
4mm Allen wrench (provided)
17/13/16 wrench (provided)
NOTE: Protect your frame
and work surface. To avoid any
damage to your frame parts and
work surface, place a protective
material on the oor or work surface
to prevent scratches and other
damage
1-1: Determine how high you want your table
top. One way to estimate the desired height is to
measure the distance from your elbow to the oor
with your arms bent at the elbow at 90 degrees
and hands in front of you. Next subtract 16 to 18
inches. This will give you the approximate table
top height for comfortable quilting, depending if
you like your table a little higher or a little lower.
The machine’s needle plate is about six inches
higher than the table top. The handlebars will be
approximately six to nine inches higher than the
needle plate. Most are comfortable with their arms
bent at 90 degrees and forearms horizontal, parallel
to the oor when free-motion quilting.
Note: To determine the approximate table
top height: Add ve inches to the height of the
leg assembly to compensate for the bottom tube
height, the leveling foot height and the table top
tube height. The frame will be leveled later on,
which may alter the height slightly.
Step 1: End Leg Assembly
NOTE: Assembly is easiest if all
connections are nger-tightened rst,
as instructed, while assembling the
frame. Tighten with the wrench only
when instructed.
Why is this important? If you tighten
as you go, you may have trouble
getting all the parts to align properly.
Left Rear Leg Upper
Rear Leg Lower
The lower leg is
xed to upper leg
with one M8 X 16
SBHCS per leg
Right Rear Leg Upper
NOTE: Height Adjustment
Be aware that there are two rivnuts
inside the leg to facilitate continuous
graduated table top height
adjustment from approximately 28”
to 34”; set both center legs using the
same height rivnut to avoid leveling
problems later on.
King Quilter Frame Assembly 9
Step 1: End Leg Assembly (continued)
1-2: Slide the left rear leg upper down
over the rear leg lower to the desired
height and insert the M8x16 screw
into one of the two holes that best
corresponds to your desired height.
Fully tighten this height screw now to
maintain the desired height.
1-3: Identify the top beam for the
left and right side legs, which have
different inside rivnut hole locations.
The side with the most rivnuts goes to
the inside of the frame.
1-4: Place the left upper beam above
the vertical rear leg assembly and the
lower leg beam below and insert the
four M8x16 SBHCS screws. Align the
back edge of the bracket with the end
of the upper beam and lower beams.
Finger tighten the screws only for now.
1-5: Thread the levelers into the
bottom of the lower beam about half
way. This will facilitate leveling the
frame later. Use the 17/13/16 wrench
if needed to adjust the levelers.
Inside view of upper beam
left hand side leg
Inside view of upper beam
right hand side leg
Outside view of
left hand leg assembly
NOTE: When a screw goes into a
slotted/elongated hole the normal rule
is for the slotted hole to be centered
on the screw if possible.
10 King Quilter Frame Assembly
Step 1: End Leg Assembly (continued)
1-6: Identify the outer side bracket
right and outer side bracket left.
Two of each bracket are used on the
outside of the leg assembly. On the left
leg assembly the left bracket is used
on the top right and bottom left and
the right bracket is used on the top left
and bottom right.
1-7: Place the brackets into place
and align three M8 x16 SBHCS screws
into each of the top brackets and
two screws into each of the bottom
brackets.
Outer side bracket left Outer side bracket right
Ce manuel convient aux modèles suivants
1
Table des matières
