Sentrol ZX200 Guide d'installation

Installation/

Programming

SENTROL ZX200/ZX210

Security System Control

Feature Overview ..................................................................................................... 5

A New Standard For Value ........................................................................................5

ZX System Advantages..............................................................................................5

”More Than A Security System“ ................................................................................5

”Self-Watch“ Fire Zone Features ................................................................................5

ZX200/ZX210 Wiring Diagram ................................................................................ 6

Control Board Terminal Descriptions ...................................................................... 7

“2 in 1” Zoning™ ..................................................................................................... 8

Conventional Methods of Wiring .......................................................................... 10

Class ‘B’ End-Of-Line Resistor Supervised Zones ......................................................10

Non-Supervised Closed Circuit Loop (No EOL Resistor Supervision) ........................10

Wireless Devices ..................................................................................................... 11

Control Station Addressing and Supervision ........................................................ 12

SSD, LCD, and VFD Control Stations .......................................................................12

LED Control Stations ...............................................................................................12

Control Station Troubleshooting ........................................................................... 13

12 VDC Outputs ..................................................................................................... 14

Direct Connection to a PC for Remote Programming .......................................... 16

Operating the System ............................................................................................ 17

Powering Up With The Control Station ...................................................................17

Installer Arming and Disarming ...............................................................................17

Installer On Premises ...............................................................................................17

Trouble Conditions .................................................................................................17

Clearing Trouble Messages......................................................................................17

Testing ....................................................................................................................17

Programming the Control ..................................................................................... 18

Introduction ...........................................................................................................18

Local Programming .................................................................................................18

Remote Programming (RPM/2 Pro).........................................................................18

LED Control Station Programming ..........................................................................18

Programming Zone Names .....................................................................................19

Table of Contents

TABLE OF CONTENTS

Installer Level Programming .................................................................................. 20

Menu Options.........................................................................................................20

Remote Connect ...........................................................................................20

Edit Function Map .........................................................................................20

Entering a New Value at a Location.....................................................20

Programming the Account Code, Report Code, and Telephone Number Digits ..

Additional Programming Notes ..........................................................21

Program User Codes......................................................................................21

Restore Factory Defaults ................................................................................21

Hours Until Next Comm Test.........................................................................22

Call RPM .......................................................................................................22

Program RF Data ...........................................................................................22

Programming RF Zone Devices Into the RF Gateway ............................22

Programming RF User Devices Into the RF Gateway .............................23

Programming RF Devices Into the Control Panel ..................................24

Function Map .........................................................................................................24

System Times ................................................................................................25

System Options .............................................................................................26

Keypad Options ............................................................................................27

Zone Definitions ............................................................................................28

User Authority Levels .....................................................................................29

Bell Output Activation ...................................................................................30

Programmable Outputs .................................................................................30

Programmable Output Activation.........................................................31

Communicator Options ................................................................................32

Event Reporting Phone Selection ...................................................................33

Telephone Numbers ......................................................................................34

Dialed Digits Allowed ...........................................................................34

Account Numbers .........................................................................................34

Zone Report Code Digits ...............................................................................35

User Report Code Digits ................................................................................36

Auxiliary Key Alarm Report Code Digits .........................................................37

Other Trouble Report Code Digits .................................................................37

Other Event Report Code Digits ....................................................................39

Programming Notes ...............................................................................................40

Specifications And Features ................................................................................... 43

List of Compatible Accessories .............................................................................. 46

Digital Communicator Table For Contact ID Formats........................................... 47

Agency Requirements ............................................................................................ 49

National Fire Protection Association (NFPA) Rules ............................................... 51

FCC Compliance ..................................................................................................... 54

TABLE OF CONTENTS

Feature Overview

FEATURE OVERVIEW

A New Standard For Value

The ZX200/ZX210 Control System sets a new stan-

dard for value and end-user benefits. Highlights in-

clude 8 zone hardwire/wireless flexibility, unique

Lifestyle Enhancement features, and an easy to use

family of keypads. The ZX200/ZX210 control is pre-

programmed at the factory with eight burglary zones

so it’s ready to power up and operate out of the

box. An optional output driver module provides 10

additional programmable outputs when desired.

ZX System Advantages

The new ZX Control System offers significant benefits

for both the installer and end user. Commonality in

programming, operation, and accessories mean ZX

controls are easier to install and program and reduce

inventory and installation costs.

Compatible wireless receivers and sensors overcome

installation obstacles and increase sales and profit po-

tential. Sensors have been engineered for long-range

stability and reliability and the modular 8-zone receiver,

with true diversity antenna, mounts anywhere for im-

proved reception and performance.

Four all-new keypads provide unique features and dis-

plays for easy end-user operation. Each keypad fea-

tures three distinct arming levels (Away, Stay & Night)

with backlit keys that show system status at a glance

and an easy to find Off key with automatic “Mute”

feature. Arming the system is easy with quick Two-

Button Arming or Double Press Arming. Arming the

system at night can be as easy as saying…or pressing

“Night, Night”.

“More Than A Security System”

The ZX200/ZX210 does more than provide reliable

home security - it provides features that complement

family lifestyles. User On Premise lets you know

when someone’s arrived.

Pager Reporting notifies users of trouble, alarm con-

ditions, or other reportable conditions on pagers with

digital displays.

“Self-Watch” Fire Zone Features

The ZX200/ZX210 ensures optimum fire zone per-

formance and safety with unique “Self Watch” fea-

tures. The ZX200/ZX210 is compatible with ESL’s

new 521 series smoke detectors for “Clean Me” Au-

tomatic Self-Diagnostic Reporting. This feature en-

ables the panel to sense when the smoke detector

needs cleaning or maintenance over the same two

wires used for power and alarm signaling. The con-

trol will then signal the Central Station that a smoke

detector maintenance trouble signal has occurred -

letting you know before a problem occurs.

For added security, the ZX200/ZX210 incorporates

Automatic Smoke Detector Reset which automati-

cally resets the smoke detectors following a manual

disarm of the fire system. The ZX200/ZX210 also

complies with new NFPA requirements for residen-

tial fire installations by providing Temporal Rhythm

Fire Coding and a Supervised Bell Circuit.

• Built-in telephone line monitor

• Supervised bell circuit

• Temporal rhythm fire bell coding

• Automatic Smoke Detector Reset

feature

• Fuse-Free

• 14" x 14" ‘Big Box’ enclosure avail-

able (model ZX210)

• 8 zones

• 2 or 4-wire fire zone capability

• Integrated Sentrol Series 4000

wireless

• Compatible with ESL 521 Smoke

Detector for automatic “Clean Me”

maintenance reporting

• Four exciting new keypads

• Pager reporting

+12V NEG TG+ TG - COM NC NO

MPI-206

TO +12V AUX TERMINAL

PG01

PROGRAMMABLE

OUTPUT 1

CONNECTION

TO NEG TERMINAL

OWNERS INSTRUCTION

NOTICE -

THIS EQUIPMENT SHOULD BE INSTALLED

IN ACCORDANCE WITH THE NATIONAL

FIRE PROTECTION ASSOCIATION’S

STANDARD 72 (NATIONAL FIRE

PROTECTION ASSOCIATION,

BATTERYMARCH PARK, QUINCY, MA

02269). PRINTED INFORMATION

DESCRIBING PROPER INSTALLATION,

OPERATION, TESTING, MAINTENANCE,

EVACUATION PLANNING AND REPAIR

SERVICE IS TO BE PROVIDED WITH THIS

EQUIPMENT.

Class II

Power-

Limited

GREEN

Red and Black Leads RED = POS. (+) BLACK = NEG. (-)

EARTH

GROUND

UNIFIED

EARTH

GROUND

QUIESCENT CHARGE CURRENT: 20mA.

Replace: Every 3 - 5 years.

FLOAT BATTERY

VOLTAGE:

13.6 - 13.8V

Max. current: 500mA.

WARNING

Internally Fused.

Do Not Short.

Do Not Connect

To A Switched

Receptacle.

TRANSFORMER

Recommended:

Basler BE 116220

16.5V / 20VA MIN.

U.L. CLASS II 50/60Hz

XFMR BELL KP

+12V NEG +12V

AUX

1500Ω

1/2 WATT

UL LISTED

SIGNALING DEVICE

Ademco AB12M

1500Ω

1/2 WATT

N.O.

N.C. ZONE 1

825Ω

1/4 WATT

1500Ω

1/2 WATT

N.C.

ZONE 6

ZONE 2

825Ω

1/4 WATT

1500Ω

1/2 WATT

N.C.

N.C. ZONE 7

ZONE 3

1500Ω(CR854)

(EOL DEVICE)

MOTION

DETECTOR

METHOD 1

METHOD 2

12V SEALED

LEAD ACID BATTERY

Yuasa B-1270

RED

WHITE

NEG ZONE

1/5

GREEN WHITE

DATA

ZONE

2/6

ZONE

3/7 NEG ZONE

4/8

2WS

SWNEG

TELCO

JACK

BLACK

CONTROL STATIONS

AND OTHER

PERIPHERALS

MODEL CR853 - 825ΩE.O.L.

MODEL CR854 - 1500ΩE.O.L.

UL LISTED RESISTORS

SMOKE DETECTOR

SENTROL 2-WIRE MODELS

(See ZX200/ZX210

Interconnect Label

P/N 64600285-NOTE 2)

POWER

LISTED RATE OF RISE OR

FIXED TEMPERATURE THERMOSTAT

1500Ω(CR854)

(CONV ZONING)

++--

POWER ALARM

CONTACTS

LISTED RATE OF RISE OR

FIXED TEMPERATURE THERMOSTAT

TO ANY ZONE DEFINED

AS 24-HOUR FIRE

POWER SUPERVISION UNIT

ESL MODEL 204-12/24V OR EQUIV.

RED

BLACK

BROWN BROWN

SMOKE DETECTOR

SENTROL 4-WIRE MODELS

(See ZX200/ZX210

Interconnect Label

P/N 64600285-NOTE 2)

CONNECT

RJ31/33/45

CORD

J-4

BATT

Telephone connection of the fire

alarm signal from this system to a

fire alarm headquarters or central

station is permitted only with the

approval of the authority having

jurisdiction.

Class II

Power-

Limited

Class II

Power-

Limited

ADEMCO AB12M

GRADE A BELL

COMMERCIAL

POLARIZATION AND

NOISE SUPPRESSION

DIODE

CONNECTION OF UL COMMERCIAL

BURGLAR AUDIBLE

JUMPER

ALL WIRING

BETWEEN CONTROL

& BELL MUST BE IN

CONDUIT.

1500Ω(CR854)

(EOL DEVICE)

BELLNEG

ZONE

2/6

KEYPAD

FIGURE 1 Suggested UL Household Burglar Alarm and/or Fire (ƒƒ) Alarm Hookup

ZX200/ZX210 Wiring Diagram

WIRING DIAGRAM

Connect a 16.5 VAC 35 VA UL Class II transformer minimum using 18 gauge

minimum 2 conductor wire.Do not exceed 50 feet.

(+)12 VDC. Combined alarm current should not exceed 1.5 amps.

Overcurrent protected at 1.85 amps (PTC2). A 1500 Ohm EOL resistor

(CR854) must be connected between the Bell and Neg terminals; otherwise a

bell output fault will occur.

BLACK WIRE - (-)12 VDC. Negative connection for Control Stations, ODM,

RF receiver, motion detectors, bell output, and other devices.

RED WIRE - (+)12 VDC 500 mA continuous power connection for Control

Stations, ODM, and RF Gateway. Overcurrent protected at 1.85 amps

(PTC1). CAUTION: Use the KP+12V and the +12V AUX terminals when

calculating total current drain.

GREEN WIRE - Connection for Control Stations, ODM and RF receiver. Use 22

gauge wire up to 1000 ft. Use 18 gauge wire up to 2000 ft.

WHITE WIRE - Connection for Control Stations, ODM and RF receiver. Use 22

gauge wire up to 1000 ft. Use 18 gauge wire up to 2000 ft.

Each loop requires a 1500 Ohm end-of-line resistor (P/N CR854) for the

primary zone and an 825 Ohm end-of-line resistor (P/N CR853) for the

secondary zone. A common negative is shared among all zones. The need for

end-of-line resistors may be eliminated on all Burglar defined zones through

programming. See Figure 2 and 3 for “2 in 1” Zoning™ wiring examples.

(-) Current limited 60 mA terminal. Negative connection for two-wire/four-

wire smoke detectors, glass break detectors, and devices requiring resettable

power. The maximum series loop resistance for a two-wire smoke loop is 20

ohms. The maximum Alarm Impedance is 500 ohms.

(+)12 VDC 500 mA continuous power. Overcurrent protected at 1.85

amps (PTC1). Used for powering motion detectors, two-wire/four-wire smoke

detectors, glass break detectors, and other accessories. CAUTION: Use the

KP+12V and the +12V AUX terminals when calculating total current drain.

TERMINAL FUNCTION DESCRIPTION

Control Board Terminal Descriptions

TERMINAL DESCRIPTIONS

XFMR

BELL

NEG

+12V

GREEN

DATA

WHITE

DATA

ZONE 1/5

NEG

ZONE 2/6

ZONE 3/7

NEG

ZONE 4/8

2WS

SWNEG

+12V

AUX

AC Input

Supervised Bell Output

(power-limited)

Common Negative

Keypad Power

(power-limited)

Local Data Bus In

Local Data Bus Out

Zone 1/5 Loop (+)

Common Negative

Zone 2/6 Loop (+)

Zone 3/7 Loop (+)

Common Negative

Zone 4/8 Loop (+)

Two-Wire/Four-Wire Smoke

Switched Negative

Auxiliary Power

(power-limited)

Method 2 wires two separate zone loops back into

one set of terminals. The panel recognizes each loop

independently because two different EOL resistor

values are used to differentiate between the Primary

Zone (1500 Ohm 1/2 Watt) and the Secondary Zone

(825 Ohm 1/4 Watt). This method provides two

zones with one set of terminals and is ideal for pre-

wire or already installed wiring.

Figure 3 “2 in 1” Zoning™ Wiring - Method 2

The resistors in Figures 2 & 3 are

1% values to maintain proper loop

resistance values. If replacements

are required, please refer to the

manufacturer for correct replace-

ments. The 1500 Ohm resistor is

color coded Brown•Green•

Black•Brown•Brown. The 825

Ohm resistor is color coded

Gray•Red•Green•Black•Brown.

All zones sense five different voltage levels enabling

one zone to act as two. Troubleshooting is simple

using just a voltmeter at the control. The control

monitors the voltage level across the zone and uses

the voltage levels in Table 1 to determine whether

the zone is normal, open, or shorted.

If a Normally Open Device (i.e., 4-

wire smoke detector) is used with

“2 in 1” Zoning™, a short will oc-

cur across both zone loops when

that device goes into alarm. It is

recommended that these types of

devices be used with Conventional

Zone wiring only.

The ZX200/ZX210 Security Control uses the “2 in

1” Zoning™ method that allows the installer to wire

two separate zones in parallel into one set of termi-

nals that will save both time and wire costs.

Each zone is uniquely identified by its end-of-line

resistor. The Primary Zone (zones 1-4) in each ter-

minal is identified by a 1500 Ohm EOL resistor. The

Secondary Zone (zones 5 - 8) is identified by an 825

Ohm EOL resistor. The Primary and Secondary zones

operate as two independent zones to provide sepa-

rate reporting, programming, and displays. Each

zone is fully programmable (See Installer Level Pro-

gramming). The zones are for Form A, Form B, or

Form C sensors. Maximum total loop wire and con-

tact resistance (not including EOL) must not ex-

ceed 100 Ohms for the loop to function properly.

There are two methods of wiring for “2 in 1” Zon-

ing™. Method 1 wires one zone loop back to the

control while a second zone loop is added in paral-

lel off the first. This method may be employed in

system retrofits, system expansions, or just simply

to save wire cost and labor.

Figure 2 “2 in 1” Zoning™ Wiring - Method 1

Secondary Zone

825Ω1/4W

1500Ω1/2W

Primary Zone

Secondary Zone

825Ω1/4W

1500Ω1/2W

Primary Zone

“2 in 1” Zoning™

NOTE

Primary Zone and Secondary Zone Infinite Ohms 5.24 - 8.25 V

Open Contacts; Loop Cut or Open

Secondary Zone Open Contact, 1500 Ohms 4.24 - 5.23 V

Primary Zone Normal

Primary Zone Open Contact, 825 Ohms 3.24 - 4.23 V

Secondary Zone Normal

Primary Zone and Secondary Zone 825 Ohms in parallel with 2.00 - 3.23 V

Normal 1500 Ohms = 532 Ohms

Primary Zone and Secondary Zone 0 Ohms 0 - 1.99 V

Shorted

CONDITION NOMINAL LOOP RESISTANCE VOLTAGE READING

Table 1 “2 in 1” Zoning™ Troubleshooting Chart

“2 in 1” Zoning™

Class ‘B’ End-Of-Line Resistor

Supervised Zones

A Class ‘B’ zone must be supervised with a 1500

Ohm 1/2 Watt end-of-line resistor (P/N CR854). This

resistor should be installed in series at the furthest

point from the control. This configuration must be

used whenever both Form A and Form B devices are

connected and provides a high degree of protec-

tion against compromise or tampering. The control

monitors the voltage level across the Primary zone

and uses the Primary zone voltage levels in Table 1

to determine whether the zone is normal, open, or

shorted. The operation of a zone is programmable

(see Installer Level Programming). Maximum total

loop wire and contact resistance (not including

EOLs) must not exceed 100 Ohms for the loop to

function properly. The 1500 Ohm EOL resistor is

optional for Form A connections but is required

for Form B.

Figure 4 Conventional Zone Wiring Method

For UL Listed systems, EOL Supervi-

sion is required.

1500Ω1/2W

Primary Zone

Normally

Open

Normally

Closed

Conventional Methods of Wiring

CONVENTIONAL WIRING

NOTE

Non-Supervised Closed Circuit Loop

(No EOL Resistor Supervision)

The EOL resistor is not required on Burglar zones. A

conventional closed circuit loop may be connected

directly to a primary zone and the zone will have

either a short or an open condition. See Installer Level

Programming for programming an unsupervised

zone. Fire zones may not be installed as unsuper-

vised. Only Burglar defined zones may be wired

non-supervised. “2 in 1” Zoning™ is not allowed.

NOTEONLY BURGLAR DEFINED ZONES MAY

BE WIRED NON-SUPERVISED. “2 IN 1” ZON-

ING™ IS NOT ALLOWED.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sentrol Système de sécurité

Sentrol

Sentrol ZX300 Instructions de montage

Sentrol

Sentrol ZX400 Manuel utilisateur

Sentrol

Sentrol ZXLCDL Manuel utilisateur

Sentrol

Sentrol ZX400 Mode d'emploi

Sentrol

Sentrol Arrowhead SC800 Instructions de montage

Sentrol

Sentrol X440F Manuel utilisateur

Sentrol

Sentrol ZXLED8 Manuel utilisateur

Sentrol

Sentrol ZXLCD Manuel utilisateur

Sentrol

Sentrol ZXCD Mode d'emploi

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur