Sensys Networks VDS240 Manuel utilisateur

Sensys Networks VDS240 Wireless Vehicle

Detection System

Access Point Controller Card Installation Guide

P/N 152-240-030-005 Rev A

April 2011

Sensys Networks

2560 Ninth Street, Suite 21

Berkeley, CA 4710

www.sensysnetworks.com

Access Point Controller Card Installation Guide

Contents

Introduction 7

What's Inside 7

Other Documents 8

Overview 9

Access Point Controller Card (APCC) 9

Contact Closure Expansion Card...................................................................................................................................................................................10

Types of APCC Configurations 10

APCC System..............................................................................................................................................................................................................10

APCC Package Contents 11

SPP Package Contents 11

Universal Mounting Kit Contents..................................................................................................................................................................................12

Additional Parts and Equipment Required 13

otes.........................................................................................................................................................................................................................14

APCC Installation Considerations 15

Identifying the SPP, Access Points and Sensors 15

SPP...........................................................................................................................................................................................................................15

Access Points.............................................................................................................................................................................................................16

Wireless Sensors.........................................................................................................................................................................................................16

Determining the Device Configuration 16

Configuration Worksheet..............................................................................................................................................................................................16

Determining Slots and Contact Closures 18

Mapping Wireless Sensors to Contact Closures 18

SPP Installation Considerations 20

Powering the SPP 20

Acquiring Power From a Traffic Controller.....................................................................................................................................................................20

Acquiring Power Form Traffic Controller Using an Isolator..............................................................................................................................................21

Voltages.....................................................................................................................................................................................................................22

Cabling......................................................................................................................................................................................................................22

Collecting Data From the APCC 22

Determining the Location of the SPP 22

Optimal Location Criteria.............................................................................................................................................................................................23

APCC Installation Procedures 24

Overview 24

Determining the Card ID and Setting it via Circuit-board Dip Switches SW1 and SW2 24

Factory Default Card ID...............................................................................................................................................................................................25

Querying the Backplane for an Assigned Address...........................................................................................................................................................25

Setting the Slot- umber With Circuit-board Dip Switch SW2..........................................................................................................................................26

Setting the Shelf- umber With Circuit-board Dip Switch SW1........................................................................................................................................26

Determining the Controller Type and Setting it via Circuit-board Dip Switch SW1 26

Connecting the Cables to Each Device 26

Cabling Summary 27

Sensys Networks, Inc. - 2 -

Access Point Controller Card Installation Guide

SPP Installation Procedures 29

Tools Required for SPP Installation 29

Step-by-Step Procedures 30

Installing the Mounting Plate on Poles..........................................................................................................................................................................30

Installing the Mounting Plate on Walls..........................................................................................................................................................................31

Installing the Mounting Plate on Beams........................................................................................................................................................................31

Configuration 32

Overview 32

Configuration Methods.................................................................................................................................................................................................33

Configuring Channels With the Front-Panel Interface 33

General Procedure.......................................................................................................................................................................................................33

Enabling / Disabling a Channel.....................................................................................................................................................................................34

Specifying the Channel Mode.......................................................................................................................................................................................35

Setting a Presence Mode Modifier (Optional).................................................................................................................................................................35

Specifying the Type of Communication Used by the Channel Status Monitor....................................................................................................................36

Starting TrafficDot and Connecting to an APCC 37

Configuring Channels With TrafficDot 38

Opening the Configuration Windows for Controller Cards................................................................................................................................................39

Specifying the Elements of the Configuration................................................................................................................................................................40

Saving the Configuration..............................................................................................................................................................................................43

Other Card Configuration Operations 43

Defining Sensor-to-Channel Mappings 43

Exiting TrafficDot 45

Appendixes 46

Appendix 1 – X Mode LED Displays for Slot Numbers 47

Appendix 2 – Circuit-board Dip Switch SW1 Settings 48

Settings for Shelf umber...........................................................................................................................................................................................48

Settings for TS1 and TS2 Controllers............................................................................................................................................................................48

Appendix 3 – Circuit-board Dip Switch SW2 Settings 49

Settings for Slot umber.............................................................................................................................................................................................49

Appendix 4 – Pre-Installation Worksheets 50

Sensys Networks, Inc. - 3 -

Access Point Controller Card Installation Guide

Document Properties

This document is reference material for the Sensys Networks VDS240 wireless vehicle detection

system from Sensys Networks, Inc.

/N 152-240-030-005 Rev A

Sensys Networks, Inc. makes no representation or warranties with respect to the contents hereof

and specifically disclaims any implied warranties of merchantability or fitness for any particular

purpose. Furthermore, Sensys Networks reserves the right to revise this publication and to make

changes from time to time in the content hereof without obligation of Sensys Networks to notify

any person or organization of such revisions or changes.

Sensys Networks and the Sensys Networks logo are trademarks of Sensys Networks, Inc. All other

products, names and services are trademarks or registered trademarks of their respective owners.

Regulatory Statements

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause

undesired operation.

The users manual or instruction manual for an intentional or unintentional radiator shall caution

the user that changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. In cases where the manual is

provided only in a form other than paper, such as on a computer disk or over the Internet, the

information required by this section may be included in the manual in that alternative form,

provided the user can reasonably be expected to have the capability to access information in that

form.

To comply with FCC’s RF exposure limits for general population / uncontrolled exposure, the

antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20

cm from all persons and must not be co-located or operating in conjunction with any other antenna

or transmitter."

Any changes or modifications to this product not authorized by Sensys Networks could void the

EMC compliance and negate the authority to operate the product.

Sensys Networks, Inc. - 4 -

Access Point Controller Card Installation Guide

RF Exposure Statement

This device has been tested and meets the FCC RF exposure guidelines. It should be installed and

operated with a minimum distance of 20 cm between the radiator of RF energy and the body of

users, operators or others.

Improper use or tampering with the device is prohibited and may not ensure compliance with FCC

exposure guidelines.

Warnings

No Safety Switching

Sensys Networks does not allow its equipment to be used for safety applications such as

controlling a mechanical gate or switching a train to avoid a collision.

Lithium Thionyl Chloride Batteries

Sensys Networks uses Lithium Thionyl Chloride batteries in the following products:

•Sensors (VSN240-F, VSN240-T, VSN240-S)

•Repeaters (R 240-B, R 240-BH, R 240-B-LL, and R 240-BH-LL)

Lithium batteries are widely used in electronic products because they contain more energy

per unit -weight than conventional batteries. However, the same properties that deliver

high energy density also contribute to potential hazards if the batteries are damaged.

Improper use or handling of the batteries may result in leakage or release of battery

contents, explosion or fire.

Following are the recommendations of the battery manufacturer for proper use and

handling of batteries in the Sensys Networks devices mentioned above:

•DO NOT charge or attempt to recharge the batteries (batteries are NOT rechargeable)

•DO NOT crush or puncture batteries

•DO NOT short-circuit the batteries

•DO NOT force over-discharge of the batteries

•DO NOT incinerate or expose batteries to excessive heating

•DO NOT expose battery contents to water

•DO dispose of batteries and devices containing batteries in accordance with local

regulations

Note: Sensys Networks wireless sensors contain no serviceable parts and should never be

disassembled. Installation and removal of sensors from pavement should only be done by

trained personnel and care should be taken to insure that the sensor casing is not punctured

or crushed.

Sensys Networks, Inc. - 5 -

Access Point Controller Card Installation Guide

Additional safety information is available from the battery's manufacturer:

•Sensor battery cell: http://www.able-battery.com/msds/ABLE_MSDS_ER14505.pdf

•Repeater battery cell: http://www.able-battery.com/msds/ABLE_MSDS_ER34615.pdf

Document Control

Sensys Networks continually reviews and revises its technical publications lease address

questions, suggestions or corrections to [email protected].

Contact Information

Sensys Networks, Inc.

2560 Ninth Street, Suite 219

Berkeley, CA 94710 USA

+1 (510) 548-4620

www.sensysnetworks.com

Sensys Networks, Inc. - 6 -

Access Point Controller Card Installation Guide

CHAPTER 1

Introduction

This guide provides information and procedures for installing Sensys Networks Access oint

Controller Card (A CC) and the A CC Serial ort rotocol (S ) digital radio in conjunction with

the Sensys Networks VDS240 wireless vehicle detection system. This document is intended to be

used by Sensys Networks customers, consultants, partners, dealers, and those who are interested in

the application of wireless communication technology to the challenges of traffic detection,

management and control.

What's Inside

This guide includes the following information:

•Chapter 1: Introduction, defines the purpose and scope of the guide.

•Chapter 2: Overview, provides an overview of the A CC and its additional

components. It also describes the contents of a product shipment.

•Chapter 3: APCC Installation Considerations, provides the installation considerations

for the A CC.

•Chapter 4: SPP Installation Considerations, provides the installation considerations

for the S .

•Chapter 5: APCC Installation Procedures, provides instructions for installing and

cabling the A CC.

•Chapter 6: SPP Installation Procedures, provides instructions for installing and

mounting the S .

•Chapter 7: Configuration, provides instructions for setting up an A CC for a particular

site.

Sensys Networks, Inc. - 7 -

Access Point Controller Card Installation Guide Introduction

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur