Sensor Networks JAWS 2.0 Manuel utilisateur
Operator Manual
Basic and Ultimate Kits
2
3
Contents
JAWS
™ Overview ................................................................... 4
Precautions ..................................................................................... 5
Setup ............................................................................................... 6
Powering the System .................................................................. 6
HD Display / Controller ................................................................... 7
Operation........................................................................................ 8
Grabber Operation...................................................................... 8
Changing Jaw Sets....................................................................... 8
Battery Status.............................................................................. 8
Power Saving Modes................................................................... 8
Battery Charging ......................................................................... 9
Operation with AC Mains Power .............................................. 10
Securing with a Lanyard............................................................ 11
Spare Parts................................................................................ 11
JAWS
™ Ultimate Kit Accessories .......................................... 12
Interchangeable Jaw Sets ......................................................... 12
Retrieval Accessories ................................................................ 12
Interconnecting Long Push Poles and Case .............................. 13
Specifications ................................................................................ 14
Care............................................................................................... 14
Warranty....................................................................................... 15
Appendix ....................................................................................... 16
Using the Accessories ............................................................... 16
Contact Us..................................................................................... 22
4
JAWS
™Overview
The
JAWS
™is a motorized retrieval device designed to be robust
and work in most environments. With a battery power pack, the tool
is portable and can be carried easily to any job site. Interchangeable
jaws sets and accessories allow equipping the tool to secure a large
variety of irregularly-shaped objects. A full line of accessories is
available in the
JAWS
™Ultimate Kit to deliver the tool to most
remote locations.
JAWS
™Basic Kit Contents
• JAWS 2.0 HD grabber
• JAWS 2.0 HD display/controller
• 50ft (15m) power/video cable
• AC adapter/charger
• operator manual
• hex key, spare screws
JAWS
™Ultimate Kit Contents
• JAWS 2.0 HD grabber • JAWS 2.0 HD display/controller
• AC adapter/charger • operator manual
• 50ft (15m) power/video cable + 50ft (15m) extension cable
• Jaw Sets: fork and tine | flat serrated | short serrated | sampling cups
curved serrated | needle-nose | tool adapter
• Tools: 2 snares: sm, lg | 2 magnets: sm, lg | Storage Case
4 hooks: sm, med, lg, xl
• Push Poles:
40 push poles - 60in (150cm) length
10 each: Ø 3
16in, 1
4in, 5
16in, 3
8in (Ø5,6,8,9mm)
4 push poles - 16in (40cm) length
1 each: Ø 3
16in, 1
4in, 5
16in, 3
8in (Ø5,6,8,9mm)
1 push pole - 12in (30cm) length × Ø 5
16in (Ø8mm)
1 push pole - 6in (15cm) × Ø 5
16in (Ø8mm)
• Push Pole Accessories:
quiver | tee handle | adjustable elbow
rubber flex joint | spring flex joint
•Miscellaneous: hex keys | spare screws | hoist lifting ring
5
Precautions
•EXPLOSION HAZARD: Do not use
JAWS
™ in an
explosive or hazardous environment.
•BODILY HARM HAZARD: Do not position
JAWS
™ near
moving machinery.
•Do not operate
JAWS
™ in temperatures below 0°F or above
120°F (-20°C - 50°C)
•Do not submerge
JAWS
™ in acids or caustics.
•Do not submerge
JAWS
™ deeper than 50 feet (15m) in water
or any other liquid. (Additional depth is attainable with a longer
main cable)
•Do not force
JAWS
™ into openings smaller than its diameter.
•Use only the supplied battery power pack as the
JAWS
™
power source.
•Keep the battery power pack away from high heat and equipment
that produces sparks.
•Replace any damaged or defective battery.
•Do not submerge battery power pack.
•Use only supplied charger to charge the battery. Follow battery
condition indicator on charger.
6
Setup
1. Connect main cable to grabber. Align the red dots and push
connector in until it clicks.
2. Connect extension cable as needed. Use without this cable is
recommended as the extra cable length consumes power that
would otherwise be available for the tool.
3. Connect cable to power pack.
4. Attach push rod or other rodding accessories to manipulate
the tool into position for grabbing.
Powering the System
ON: Press in the switch and release to start the system, the
status LED will blink Green while starting. The video will
display after 15 seconds. The status LED will change to Blue
indicating the system is ready.
OFF: Press in the switch for 2 seconds to power down the
system.
Power / Video
Cable
HD Display
/ Controller
HD Grabber
7
HD Display / Controller
Switch
Status LED
Cable Connector
HDMI Output
Power Connector
Battery Access
Folding Stand
¼”-20 Mount
For Lanyard
¼”-20 Mount
For Lanyard
8
Operation
Grabber Operation
Press the switch forward to close the tool jaws. When the jaws
have tightened fully, the status LED will change to Yellow.
Press the switch rearward to open tool jaws.
Changing Jaw Sets
To change the preferred jaw set on tool, use a 3/32-inch hex key
to remove the socket head screws on each jaw.
Slide each jaw off the tool and clean the interfacing surfaces.
Slide preferred jaw onto tool and install socket head screw.
Battery Status
Press the switch to the left to display the battery condition on the
status LED.
100% - 3 Green blinks
80% - 2 Green blinks
60% - 1 Yellow blink
40% - 1 Red blink
20% - 1 long Red blink
Power Saving Modes
After 10 minutes of no switch activity, the system will dim the
video display. The status LED will blink Blue. Moving the switch
will awaken the system.
After 20 minutes of no switch activity, the system will sleep using
a small amount of battery power. The status LED will blink
Blue. Moving the switch will awaken the system.
After 30 minutes of no switch activity, the system will completely
shut down and use no power. See Powering the System to
restart.
9
Battery Charging
Place the charger on a flat, level surface away from sources of
heat and moisture.
Plug the connector from the AC adapter into the back of the
charger and connect the adapter to the mains AC supply using
the cable supplied.
Place the battery into the battery bay ensuring that the 5-way
connector is fully seated. The LEDs in the status window will
provide status information and the charger will automatically
begin charging.
Green flashing: Battery charging
Green solid: Battery fully charged
Red: Error
Note: The battery does not charge while installed in the
controller. Follow instructions below to charge battery.
Open the battery compartment by loosening the two screws on the
controller back cover. Pop the cover up and off.
Remove the battery and insert it into the supplied charger. Full
charge time is generally 2 hours.
10
Reverse the above operation for portable / battery operation of the
JAWS tool.
Operation with AC Mains Power
Plug the barrel connector from the AC adapter into the power
jack on the HD Display / Controller. Connect the adapter to the
mains AC power outlet.
Power on the system, see Powering the System section.
The AC adapter will power only the tool system, the battery will
not charge if installed. The system will use AC power if available
first, and only use battery when AC is not present. Restarting the
system is necessary when changing power sources.
Table des matières
