Sensear smartPlug Manuel utilisateur
smartPlug
USER GUIDE
1
English
English
English
GETTING STARTED
1. Headset anatomy
2. Wearing the headset
3. Fitting the Earbuds
4. Charging the headset
5. Power up the headset
6. Environmental modes
7. Connecting A Two Way
Radio
8. Using Bluetooth
9. Bluetooth pairing and
connecting
10. Using Short Range
11. Using FM Radio
12. Troubleshooting
1. HEADSET ANATOMY
Right indicator light
Right Ear Bud
Disposable Foam Tip
Left Ear Bud
Inline PTT
Inline 1 Button
Inline 2 Button
Left Indicator Light
Power Button
Volume Up Button
Multi Function Button
Volume Down Button
Main Unit with Belt Clip
Two-Way Radio Connection
Mini USB Connection
Battery Rechaging Connection
1
English
3
2
2.WEARING THE HEADSET
The smartPlug is a state of the art hearing protection
communication system that allows you to retain situational
awareness while being in full contact with all your
communication devices.
Situational awareness is provided by processing
technology and environmental microphones within the
Earbuds.
Contact through other communication devices is enabled by:
- Two Way Radios interface cables (sold separately).
- Bluetooth to Two Way Radios and cell phones (if installed)
- Direct Headset to Headset communications through
Short Range (if installed)
The smartPlug is designed to be worn with the main housing
attaching to the belt or pant seam, and the Inline PTT
attaching to the shirt / upper garment of the user.
Note: For SR communications, the best communication
range is achieved with the Inline PTT set as high up on the
user as possible.
Ear
Ear
Microphone
Ear Buds
Inline PTT
Main Housing
Earbud
Foam Tip
In-Ear speaker
and microphone
English
3
2
3. FITTING THE EARBUDS
1. Place Disposable Foam
Tip between thumb and
forefinger.
6. Using your opposite hand, pull
your ear upward and outward.
Insert the Ear Bud deeply into the
ear -as you would normally do with
a Foam Ear Plug.
7. Hold the Ear Bud in place for
30 seconds while the Foam Tip
expands.
8. Check to ensure the Ear Buds
are correctly inserted.
9. A poor fit will be visible by the
Earbuds being far away from the
ear. No foam tip should be visible.
Repeat the process until a good
fit is achieved.
2. Roll Foam Tip to a
compressed, crease free
cylinder
3. Push the Foam Tip all the
way onto the Ear Bud spout.
4. Roll the Foam Tip again
between the thumb and
forefinger.
5. Ensure the Foam Tip
remains a compressed,
crease free cylinder on the
Ear Bud.
It is critical the earbuds are correctly fitted to ensure the correct level of hearing protection and communication abilities. The Earbuds
incorporate an in-ear pickup, if the Earbuds are not fitted correctly, the speech quality may be lower than expected.
English
5
4
4. CHARGING
Your headset comes supplier with a charger. Do not
attempt to use third party chargers as damage may
result.
The headset should be regularly charged. To charge
your headset connect the charger to the headset and
connect to the mains power.
While charging the Right Indicator LED will be Red.
When charging is complete the LED will turn Green.
Note: Be sure to charge your headset fully before first
use.
Note: Your headset will automatically power up when the
charger is connected to the headset.
Charge Time :5 hours
Battery Life: 15 hours
Your headset is powered by a built-in high capacity Lithium Ion battery.
Thisis designed to last the life of your headset and should be returned to
the manufacturer for replacement and servicing. Any attempt to access
the battery will damage the headset. Please see accompanying smartPlug
Headset Information guide for additional safety battery precautions.
Right Indicator
Red: Charging
Green: Charge Complete
Charger
Charging Jack
English
5
4
5. POWER ON HEADSET
Your headset must be powered up to use
situational awareness and the communication
connectivity features.
Power on / off
To power up your headset press and release the
power button.
To power off your headset press and hold the power
button until the unit powers off.
6. ENVIRONMENTAL MODES
Your smartPlug headset features situational
awareness technology.
(Speech Enhancement, Noise Suppression)
allows you to be in audible contact with your
surroundings while wearing your headset.
To toggle situational awareness on or off
momentarily press and release the power button.
Right Indicator
Green fast flash: Quiet Mode
Green slow flash:
active
Red flash:
Battery low (less than 1 hour)
Off: Headset off
Power Button
English
English
7. CONNECTING TWO WAY RADIO
smartPlugheadset can be connected to most Two Way
Radios through interface cables (sold separately).
1. Connect the Two Way Radio Cable into the Two way
Radio Connector located on the bottom of the Main
Unit.
2. Turn the Two Way Radio on. A tone will be heard
through the headset indicating it has detected the
Two Way Radio.
3. Adjust the volume of the Two Way Radio
communication by the normal controls of your Two
Way Radio until a comfortable level is reached.
4. To transmit, press and hold the Inline 1 Button or
the button programmed by your dealer.
Note: See ‘Using Bluetooth’ for more information on
connecting Two-Way Radios by Bluetooth.
Two Way Radio Connector
Two Way Radio Cable
Inline PTT
Inline 1 Button
7
6
English
8. USING BLUETOOTH
smartPlug Headsets also feature Bluetooth connectivity
(if installed). Bluetooth enables wireless connections to some
models of Two Way Radio, industrial computers, vibration analysers
and most Cell phones. If Bluetooth is installed on your smartPlug,
the following details apply.
Default automatic connection setting: When the headset powers
up, the smartPlug searches for previously paired devices. If a
previously paired device is within range, it will automatically attempt
to reconnect to this device. A blue light will flash slowly if a Bluetooth
connection is made and you will hear a tone in the headset.
Note: When entering pairing mode the smartPlug forgets all
previously connected devices.
Note: Bluetooth is discoverable for 2 minutes in pairing mode. If no
connection has been made within this time, the process will need to
be repeated.
Bluetooth Phone :To answer calls, press the Multi Function Button
(or programmed button, consult your dealer). To end or reject a
call, press and hold the Multi Function button for 2 seconds.
Bluetooth PTT:Some radios and cell phones feature PTT over
Bluetooth. Please consult your dealer for more information.
7
6
English
English
9
8
9. BLUETOOTH PAIRING AND
CONNECTING
Bluetooth pairing to new device:
For Bluetooth functionality, the smartPlug headset must be paired
and connected.
1. Enable Bluetooth on the device which you want to connect to the
smartPlug
2. Power up the smartPlug
3. Hold the Multi Function Button for 5 seconds to enable pairing.
A blue light indicator will switch on.
4. Follow pairing instructions on the device that you want to
connect to, search and pair the smartPlug. If asked for a
passkey, enter 0000
5. Once paired, the headset will automatically connect and the blue
light indicator will flash slowly.
6. If automatic connection fails, use the device instructions to
connect to the smartPlugheadset.
Multi Function Button
Autres manuels pour smartPlug
1
Table des matières
Langues :
Manuels Système de conférence populaires d'autres marques
Kramer
Kramer VIA GO Manuel utilisateur
AVT
AVT MAGIC AC1 Go Manuel utilisateur
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manuel utilisateur
Sony
Sony PCS-I150 Manuel utilisateur
Middle Atlantic Products
Middle Atlantic Products VTC Series Manuel utilisateur
Prentke Romich Company
Prentke Romich Company Vanguard Plus Mode d’emploi
