Sennheiser RS 130 Manuel utilisateur
Bedienungsanleitung
Instruction Manual
Notice d´emploi
Istruzioni per l´uso
Instrucciones para el uso
Instruções de Uso
Gebruiksaanwijzing
Käyttöohje
Οδηγίες χειρισµού
RS 130
Sennheiser electronic GmbH & Co. KG
30900 Wedemark, Germany
Phone +49 (5130) 600 0
Fax +49 (5130) 600 300
www.sennheiser.com
Printed in China Publ. 05/05 511733/A02
12ON/OFF
5
3
4
8
6VOLUME 7TUNE
a
)
b)
SURROUND
11
ENGLISH
RS 130
The RS 130 is an up-market wireless RF headphone system suitable
for use with hi-fi systems and televisions. The headphones are very
comfortable to wear and the system incorporates a variety of
technical innovations such as:
yTransmitter with automatic on/off function
yAutomatic transmitter search-tuning with memory function
ySelf-learning automatic level control with memory function
yAcoustic signals provide feedback on the functions
y“Noise Gate“ function reduces hissing noise, e.g. during pauses
yIntelligent battery charging technology
yEnhancement of the 3D and the bass portion of the stereo signal
Delivery includes
yHDR 130 headphones
y2 x AAA size Ni-MH rechargeable battery, 1.2 V
yTR 130 transmitter with audio connecting cable (permanently
connected)
yNT-RS 100 mains unit
yAdapter 3.5 mm/6.3 mm
yRCA phono plug (926 MHz variant only)
yInstructions for use
12
ENGLISH
Safety instructions
Never open the transmitter nor the receiver, otherwise you can be
injured and the warranty becomes null and void.
Attention: Do not wear the headphones in situations
which require special attention (e.g. in traffic or when
performing skilled jobs).
Attention: Listening at high volume levels can lead to
hearing defects.
Attention: Do not charge standard batteries via the
headphones! Only use rechargeable batteries (danger of
explosion)!
Dispose of exhausted rechargeable batteries at special
collection points or return them to your specialist dealer.
yAlways keep the system dry and do not expose it to extreme
temperatures (ideally 10–35°C).
yUse the system with care and set it up in a clean, dust-free
environment.
yVarnish or furniture polish may degrade the rubber feet of the
transmitter, which could stain your furniture.
yDo not store your headphones on a glass dummy head, chair
armrest, or similar for long periods of time as this can widen the
headband and reduce the contact pressure of the headphones.
yUse a soft cloth for cleaning the units. Do not use abrasive
cleaners.
Wall mounting
The transmitter is prepared for wall mounting. The required
mounting hardware (screws and plugs) is not included in the
delivery.
13
ENGLISH
Connecting the transmitter (Fig. 1)
Establish the necessary connections (mains unit, audio connecting
cable).
Removing the ear cushions (Fig. 2 and 3)
The ear cushions are secured to the earcups by means of a quarter
turn fastener. To remove an ear cushion, turn it in the direction of
the arrow until you overcome a slight resistance and lift it off the
earcup.
Inserting the rechargeable batteries (Fig. 4)
Remove the left ear cushion (Fig. 2 and 3).
Insert the rechargeable batteries.
Attention: Observe correct polarity when inserting the batteries!
Charging the rechargeable batteries
For charging the batteries, place the headphones on the charging
cradle of the transmitter. (The headphones automatically turn off
during charging.) The red LED “CHARGE” lights up during the
charging process. If the batteries are fully charged, the transmitter
automaticallyswitchestotricklechargingandtheredLED“CHARGE”
flashes slowly.
Charge the batteries for at least 16 hours prior to first time use.
Subsequent charging time is about the same time as the previous
operating time.
Alwaysstoretheheadphonesonthetransmittertoensurethatthey
are fully charged when they are needed. The intelligent battery
charging technology prevents overcharging. If you do not use the
head-phones for extended periods of time, please remove the
batteries and disconnect the transmitter’s mains unit from the
mains.
Nearly discharged batteries will significantly reduce the sound
quality. Approx. 10 minutes before the batteries are completely
discharged, an acoustic warning signal is produced (two long beeps,
see table on page 16).
14
ENGLISH
Turning the transmitter on and off (Fig. 5)
Turn on the sound source. This automatically activates the
transmitter and the green LED “ON/OFF” lights up. If the sound
source is turned off, the transmitter is automatically deactivated
after approx. 3 minutes (the LED “ON/OFF” goes off).
Note:The automatic level control onlyfunctions if the volume of the
sound source is sufficient.
Turning the headphones on and off (ON/OFF, Fig. 5)
Move the “ON/OFF” switch on the headphones to the position “ON”.
The headphones then start the transmitter search-tuning.
Adjusting the volume (VOLUME, Fig. 6)
Use the “VOLUME” control to adjust the volume on the headphones.
Auto-tuning – automatic transmitter search-tuning with
memory function (TUNE, Abb. 7)
Note: The transmitter must be activated (green LED “ON/OFF” lit)
and the headphones must be turned on.
By pressing the TUNE button or after turn-on, the headphones start
scanning the whole frequency range for a transmitter signal. If a
transmitter signal is found, the transmitter search-tuning stops and
theheadphonesproduce–dependingontheselectedchannel–one,
two or three beeps. The audio transmission then starts.
If, for some reason, the signal found is not the correct one (e.g. from
another nearby system), press the TUNE button again and the
transmitter search-tuning is continued. When turning on the head-
phones, they automatically start the transmitter search-tuning on
the last selected channel.
If no transmitter signal is received for an extended period of time
(e.g. the range is exceeded or the transmitter is deactivated), six
short beeps are produced. After approx. 10 minutes, the
headphones automatically turn off. By pressing the TUNE button,
the headphones can be turned on again.
15
ENGLISH
Self-learning automatic level control with memory
function
The transmitter is equipped with an automatic level control which
ensuresthattheheadphonesalwaysreceiveanoptimumsignal.The
level is continuously adjusted during operation and remains stored
as long as the transmitter is connected to the mains.
Under-modulation (audio signal too low)
With under-modulation, the yellow LED “INPUT LEVEL” flashes
slowly. If this happens, gradually increase the volume of the sound
source. If the audio signal remains too weak, an optimum trans-
mission is not possible. It could be that the transmitter is
deactivated after some time.
Over-modulation (audio signal too high)
Withover-modulation,theyellowLED“INPUTLEVEL”flashesrapidly.
If this happens, gradually reduce the volume of the sound source.
Enhancement of the 3D and the bass portion of the
stereo signal (Fig. 8)
The RS 130 system is equipped with the so-called sound retrieval
system (SRS), which significantly enhances the three-dimensional
and the bass portion of the stereo signal. To activate the sound
retrieval system, move the slide switch “SURROUND” on the
transmitter to the right. The yellow LED “SURROUND” lights up.
Automatic noise reduction
In addition, the transmitter features a “Noise Gate” function, which
reduces hissing noise when no audio signal is transmitted (e.g.
during pauses).
16
ENGLISH
Meanings of the LEDs and acoustic signals
Transmitter, LED Status Meaning
ON/OFF
(green) lit Audio signal is
present, transmitter is
activated
CHARGE
(red) lit Rechargeable
batteries are being
charged
flashes slowly Rechargeable
batteries are fully
charged, transmitter
has switched to trickle
charging
SURROUND
INPUT LEVEL
(yellow)
lit “SURROUND” function
is activated
flashes slowly Audio signal too low
flashes rapidly Audio signal too high
Headphones,
acoustic signals Meaning Commentary
6 short beeps No audio signal
(transmitter is
not activated,
out of range)
Automatic turn-off
after approx. 10
minutes
2 long beeps Rechargeable
batteries are flat Automatic turn-off
after approx. 10
minutes
Sequence of 3
beeps Manual or
automatic
turn-off
—
1,2or3beepsafter
pressing TUNE Headphones
tunedtochannel
1, 2 or 3
—
17
ENGLISH
Turning the acoustic signals (beeps) on and off
The acoustic signals of the headphones can be turned on or off as
follows:
yTurn the headphones on.
yPress the TUNE button for 5 seconds.
yTurn the headphones off.
yIf the acoustic signals are turned on, the headphones produce a
sequence of beeps at turn-off. If no beeps are produced, the
acoustic signals are now turned off.
If problems occur...
yCheck if all jack plugs are connected correctly.
yMake sure that the batteries are charged.
yCheck if the batteries are inserted correctly and that the polarity
is correct.
yCheck if the headphones and sound source are turned on and
that the volume of the headphnes and soundsourceissufficient.
yMove closer to the transmitter.
yChoose a different channel on the transmitter.
yPress the TUNE button again.
yReset the system:
Remove the rechargeable batteries from the headphones and –
atthesametime– interruptthe powersupply of the transmitter
for at least 30 seconds.
ySome electronic devices (e.g. televisions) can cause interference,
which can be eliminated by increasing the distance between the
transmitter and the interference source.
yTry to operate the transmitter with a different sound source.
Should the problem persist, please contact your authorized dealer
for assistance.
18
ENGLISH
Accessories
yAdditional headphones: HDR 130 (864 MHz) Cat. No. 009932
HDR 130 (926 MHz) Cat. No. 009933
yReplacement ear cushions: Cat. No. 511791
OnlyuseoriginalSennheisercomponentsand spareparts,otherwise
the units can be damaged and the warranty becomes null and void.
Warranty
2-year warranty
Type approval regulations
Please observe the repective country-specific type approval
regulations!
Specifications
Modulation FM stereo
Frequency range see type plate on the bottom of transmitter
AF frequency response 18 Hz–21 kHz
Signal-to-noise ratio typ. > 68 dBA
TR 130 transmitter
RF output power < 10 mW (864 MHz variant)
< 0.75 mW (926 MHz variant)
Power supply 9 V DC via NT-RS 100 mains unit
Current consumption < 1.8 VA
Channels 3
Connector 3.5 mm jack plug (864 MHz variant)
RCA plug (926 MHz variant)
Weight approx. 430 g (incl. audio connecting cable)
Dimensions width: 85 mm,
depth: 133 mm,
height: 225 mm (incl. charging cradle)
HDR 130 headphones
Transducer principle dynamic, circum-aural, open
Max. SPL at 1 kHz 104 dB
THD < 0.5%
Power supply 2AAA sizeNi-MHrechargeablebatteries(LR03)
Charging time approx. 16 h (full charge)
Operating time approx. 22 h (with fully charged batteries)
Weight approx. 275 g incl. batteries
Autres manuels pour RS 130
4
Table des matières
Autres manuels Sennheiser Casque sans fil
Sennheiser
Sennheiser HD 450BT Manuel utilisateur
Sennheiser
Sennheiser HDR 175 Manuel utilisateur
Sennheiser
Sennheiser RS 120 II Manuel utilisateur
Sennheiser
Sennheiser MOMENTUM 4 Manuel utilisateur
Sennheiser
Sennheiser RS 175 Manuel utilisateur
Sennheiser
Sennheiser TR 185 Manuel utilisateur
Sennheiser
Sennheiser RS 120-W Manuel utilisateur
Sennheiser
Sennheiser MOMENTUM Black Mode d’emploi
Sennheiser
Sennheiser RS195 Manuel utilisateur
Sennheiser
Sennheiser RS195 Manuel utilisateur
Sennheiser
Sennheiser HD 4.50BTNC Manuel utilisateur
Sennheiser
Sennheiser MOMENTUM True Wireless 2 M3IETW2 Manuel utilisateur
Sennheiser
Sennheiser PXC 550-II Manuel utilisateur
Sennheiser
Sennheiser MOMENTUM 4 Manuel utilisateur
Sennheiser
Sennheiser RS 2000 Manuel utilisateur
Sennheiser
Sennheiser GSP 670 Manuel utilisateur
Sennheiser
Sennheiser SEBT2 Manuel utilisateur
Sennheiser
Sennheiser RS 175 Manuel utilisateur
Sennheiser
Sennheiser TR 175 Manuel utilisateur
Sennheiser
Sennheiser RS 120 II Manuel utilisateur
