Sennheiser EK100G2 Manuel utilisateur

EK 100 G2 bodypack receiver

(

)

+ , - . /

Operating controls LC display panel

!Audio output (AF OUT), 3.5 mm jack socket

(unbalanced)

#Antenna

$Red LED for operation and

battery status indication (ON/LOW BAT)

4Green LED for RF signal indication (RF)

%SET button

*!/"rocker button (DOWN/UP)

(Battery compartment

)Battery compartment cover

3Unlocking button

&ON/OFF button

(serves as the ESC (cancel) key in the

operating menu)

'LC display

"Alphanumeric display

1“B.CH“ – appears when the channel bank and

the channel number are displayed

2“MHz“ – appears when the frequency is displayed

+4-step battery status display

,Lock mode icon

(lock mode is activated)

-“PILOT” display

(pilot tone evaluation is activated)

.“MUTE” display

(audio output is muted)

/7-step level display for received audio signal “AF”

07-step level display for received RF signal “RF”

SK 100 G2 bodypack transmitter

(

)

, - . / 0

Operating controls LC display panel

!Microphone/line input (MIC/LINE),

3.5 mm jack socket

#Antenna

$Red LED for operation and

battery status indication (ON/LOW BAT)

%Yellow LED for audio peak (AF PEAK)

&SET button

+!/"rocker button (DOWN/UP)

)Battery compartment

*Battery compartment cover

2Unlocking button

'ON/OFF button

(serves as the ESC (cancel) key in the

operating menu)

(LC display

1MUTE switch

"Alphanumeric display

3“B.CH“ – appears when the channel bank and the

channel number are displayed

4“MHz“ – appears when the frequency is displayed

,4-step battery status display

-Lock mode icon

(lock mode is activated)

.“PILOT” display

(pilot tone transmission is activated)

/“MUTE” display

(audio input is muted)

07-step level display for audio signal “AF”

Indications and displays on the receivers

Operation and battery status indication (EK 100 G2 only)

The red LED (LOW BAT/ON) !provides information on the current operating

state of the EK 100 G2:

Red LED lit up: The receiver is switched on and the capacity of the bat-

teries/accupack BA 2015 is sufficient.

Red LED flashing: The batteries are/the accupack BA 2015 is going flat

(LOW BAT)!

In addition, the 4-step battery status display "on the display panel provides

information on the remaining battery/accupack BA 2015 capacity:

Transmitter battery status indication (EM 100 G2 only)

When the capacity of the transmitter batteries/accupack is so low that the

batteries/accupack must soon be replaced (LOW BAT), the transmitter trans-

mits information on its remaining battery/accupack capacity to the

EM 100 G2 receiver and the transmitter low battery icon #starts flashing on

the receiver display panel.

“MUTE” display

The “MUTE” display $or %appears when

!the RF signal of the received transmitter is too weak,

!the received transmitter has been muted (with the pilot tone transmission

or evaluation activated).

RF signal indication (EK 100 G2 only)

The green LED (RF) &at the front of the EK 100 G2 lights up when an RF sig-

nal is being received.

3 segments: capacity approx. 100 %

2 segments: capacity approx. 70 %

1 segment: capacity approx. 30 %

Battery icon flashing: LOW BAT

EK 100 G2

EM 100 G2

(

Modulation display of the receiving transmitter

The level display for audio signal “AF” shows the modulation of the transmit-

ter.

When the transmitter’s audio input level is excessively high (AF peak), the

receiver’s level display for audio signal “AF” shows full deflection.

“PILOT” display

The “PILOT” display !or "lights up when the pilot tone evaluation is acti-

vated (see: „Activating/deactivating the pilot tone transmission or pilot tone

evaluation“ on page 35).

Diversity display (EM 100 G2 only)

The EM 100 G2 receiver operates on the true diversity principle (see: „Diver-

sity reception“ on page 41).

The diversity display #indicates whether diversity section I (i.e. antenna 1)

or diversity section II (i.e. antenna 2) is active.

Display backlighting (EK 100 G2 only)

After pressing a button, the display remains backlit for approx. 15 seconds.

EM 100 G2

EK 100 G2

EM 100 G2

EK 100 G2

Indications and displays on the transmitters

Operation and battery status indication

The red LED (LOW BAT/ON) provides information on the current operating

state of the transmitter:

Red LED lit up: The transmitter is switched on and the capacity of the

batteries/accupack BA 2015 is sufficient.

Red LED flashing:

The batteries are/the accupack BA 2015 is going flat (LOW

BAT)!

In addition, the 4-step battery status display !on the display panel provides

information on the remaining battery/accupack BA 2015 capacity:

“MUTE” display

The “MUTE” display "appears on the display panel when the transmitter is

muted (see: „Muting the transmitters“ on page 23).

Modulation display

The level display for audio signal (AF) shows the modulation of the transmit-

ter.

AF peak indication (SK 100 G2 only)

The yellow LED (AF PEAK) #at the front of the SK 100 G2 lights up when the

audio input level is excessively high (AF peak) and overmodulates the trans-

mitter. At the same time, the 7-step level display for audio signal “AF” shows

full deflection for the duration of the overmodulation.

“PILOT” display

The “PILOT” display $lights up when the transmitter display panel if the

pilot tone transmission is activated (see: „Activating/deactivating the pilot

tone transmission or pilot tone evaluation“ on page 35).

Display backlighting (SK 100 G2 only)

After pressing a button, the display remains backlit for approx. 15 seconds.

3 segments: capacity approx. 100 %

2 segments: capacity approx. 70 %

1 segment: capacity approx. 30 %

Battery icon flashing: LOW BAT

The operating menu

A special feature of the Sennheiser ew 100 G2 series is the similar, intuitive operation. As a result, the units are easy

to operate and adjustments to the settings can be made quickly and “without looking” – even in stressful situati-

ons, for example on stage or during a live show or presentation.

The buttons

Overview of menus

Buttons Mode To ...

ON/OFF

POWER

(EM 100 G2 only)

Standard display turn the transmitter or receiver on and off

Operating menu cancel the entry and return to the standard display

Setting mode cancel the entry and return to the standard display

SET

Standard display get into the operating menu

Operating menu get into the setting mode of the selected menu

Setting mode store the settings and return to the previous menu level

!/"

Standard display without function

Operating menu change to the previous menu (!) or change to the next menu (")

Setting mode adjust the setting of the selected menu: option (!/")

Display Receivers Transmitters

BANK Switching between channel banks Switching between channel banks

CHAN Switching between the channels in

a channel bank

Switching between the channels in

a channel bank

TUNE Setting a receiving frequency for the channel

bank “U” (user bank)

Setting a transmission frequency for the channel

bank “U” (user bank)

SCAN Scanning the selected channel bank for free

channels 

SENSIT Adjusting the sensitivity (AF)

AF OUT Adjusting the audio output level 

SQELCH Adjusting the squelch threshold 

DISPLY Selecting the standard display Selecting the standard display

NAME Entering a name Entering a name

RESET Loading the factory-preset default settings Loading the factory-preset default settings

PILOT Activating/deactivating the pilot tone

evaluation

Activating/deactivating the pilot tone

transmission

LOCK Activating/deactivating the lock mode Activating/deactivating the lock mode

EXIT Exiting the operating menu and returning to the

standard display

Exiting the operating menu and returning to the

standard display

Working with the operating menu

By way of example of the “TUNE” menu, this section describes how to use the

operating menu.

After switching the unit on, the standard display is shown on the display

panel.

Getting into the operating menu

!Press the SET button to get from the standard display into the operating

menu. The last menu selected flashes on the display.

Selecting a menu

!Press the "/#buttons to select a menu.

!Press the SET button to get into the setting mode of the selected menu.

The current setting that can be adjusted flashes on the display.

Adjusting a setting

!Press the "/#buttons to adjust the setting. By briefly pressing the "/#

buttons, the display jumps either forwards or backwards to the next set-

ting. In the “CHAN”, “TUNE” and “NAME” menu, the "/#buttons feature

a “fast search” function. If you hold down a button, the display cycles con-

tinuously. The “fast search” function allows you to get fast and easily to

your desired setting. The new setting flashes on the display until it is

stored.

Storing a setting

!Press the SET button to store the setting. “STORED” appears on the dis-

play, indicating that the setting has been stored. The display then returns

to the previous menu level.

With most menus, new settings become effective immediately without

having to be stored. An exception are the “BANK”, “CHAN”, “TUNE” and

“RESET” menus of the transmitters and the “RESET” menu of the recei-

vers. With these menus, new settings only become effective after they

have been stored (“STORED” appears on the display, indicating that the

setting has been stored).

Exiting the operating menu

!Select the “EXIT” menu to exit the operating menu and to return to the

standard display.

When you have entered the operating menu, the ON/OFF button or the

POWER button (EM 100 G2 receiver only) serves as the ESC (cancel) key,

i.e. by briefly pressing the ON/OFF or POWER button, you cancel your entry

and return to the standard display.

EM 100 G2

EK 100 G2

Trans-

mitters

Operating menu of the receivers

SET

Changing the channel

STORED

CHAN

790.025

B . CH

1. 790.100

B . CH

SET

Current channel (display

depends on "DISPLY"

setting)

: Channel 01...04

SET: Stores the setting

BANK

Changing the channel

bank

BANK

SET

Current channel bank !

: 1...8, U (User

Bank)

SET: Stores the setting

STORED

AF OUT

Setting the audio output

level

LEV +18

LEV

-24

SET

Current audio output

level

: (in steps of 6 dB):

EM 100 G2:+18...0...-24 dB

EK 100 G2: +12...0...-30 dB

SET: Stores the setting

SQELCH

Setting the squelch

threshold

SET

Current squelch

threshold

: LO, MID, HI

SET: Stores the setting

SQ LO

SQ HI

STORED

DISPLY

TUNE

Setting the frequency

for channel bank "U"

Current frequency on

the selected channel

: Receiving

frequency in steps of

25 kHz

SET: Stores the setting

790.025

791.125

SET

STORED

SET

U. U.

SCAN START

Scanning the selected

channel bank for free

channels

: CLEAR, START

Start scan = START

SET: Scans the selected

channel bank for free

channels

CLEAR

Delete result = CLEAR

SET: Releases locked

channels

04 CH FREE

STORED

SET

STORED

EXIT

SQELCH

RESET

Loading the factory-

preset default settings

SET

Security check

OK, NO

"reset" = OK:

SET: Receiver loads

factory-preset default

settings (only pilot tone

setting is kept), receiver is

restarted, standard display

appears

RST. NO

RST. OK

PILOT

Activating/deactivating

the pilot tone evaluation

SET

Pilot tone evaluation

activated or deactivated

ON, OFF

SET

Stores the setting

ON, OFF

Lock mode = ON:

SET: Stores the setting

(STORED), returns to

standard display

Lock mode = OFF:

SET: Stores the setting

PLT. ON

PLT. OFF

OFF

LOCK

Activating the lock mode

SET

Lock mode activated or

deactivated

LOC.OFF

OFF

LOC.ON

EXIT

Exiting the operating

STORED

NAME

SET

Current receiver name

Assigning the receiver

a name

Enter a name

(6 characters)

Letters w/o pronounciation

marks, numbers from 0...9,

special characters, spaces

SET: 5 x next character,

then store

OCAL G

CAL

DISPLY

Switching between the

standard displays

SET

Current standard display

Select standard

display

EM 100 G2: FREQ, NAME

EK 100 G2: FREQ, NAME,

CHAN

SET

Stores the setting

FREQ

NAME

STORED

BANK

"reset" = NO

SET

Reset is cancelled

Operating menu of the transmitters

SET BANK

Changing the channel

bank

BANK

SET

Current channel bank

1...8, U (User

Bank)

SET

Stores the setting

STORED

CHAN 1.03 B.CH

SET

Current channel (display

depends on "DISPLY"

setting)

Changing the channel

Channel 01...04

SET

Stores the setting

SENSIT

Setting the sensitivity

-10 dB -30 dB

SET

Current sensitivity

setting

SK 100 G2: 0...-30 dB

SKM 100 G2: 0...-30 dB

SKP 100 G2: 0...-50 dB

SET

Stores the setting

DISPLY

Switching between the

standard displays

SET

Current standard display

: FREQ, NAME,

CHAN

SET

Stores the setting

FREQ

NAME

STORED

TUNE

Current frequency on

the selected channel

Transmission

frequency in steps of

25 kHz

SET

Stores the setting

790.025

791.125

SET

STORED

1.02 B.CH

MHz MHz

NAME

Setting the frequency

for channel bank "U"

EXIT

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sennheiser Récepteur

Sennheiser

Sennheiser SYS 2013-PLL - Manuel d'utilisation

Sennheiser

Sennheiser EM2003-9 Manuel utilisateur

Sennheiser

Sennheiser INFRAROT HDI 1029-PLL 16 Manuel utilisateur

Sennheiser

Sennheiser Digital 6000 Series Manuel utilisateur

Sennheiser

Sennheiser Tourguide 1039 Manuel utilisateur

Sennheiser

Sennheiser HDI 830 Manuel utilisateur

Sennheiser

Sennheiser HDI 91 Dimensions

Sennheiser

Sennheiser EW-D EM Manuel utilisateur

Sennheiser

Sennheiser HDE 2020 D - Manuel utilisateur

Sennheiser

Sennheiser EVOLUTION WIRELESS G2 100 Manuel utilisateur

Sennheiser

Sennheiser EM 1003 Manuel utilisateur

Sennheiser

Sennheiser EM 2000 Manuel utilisateur

Sennheiser

Sennheiser HDE 300-6 Manuel utilisateur

Sennheiser

Sennheiser EK 300 IEM Manuel utilisateur

Sennheiser

Sennheiser EK 2013 PLL - ANNEXE 341 Manuel utilisateur

Sennheiser

Sennheiser EK 2012 Manuel utilisateur

Sennheiser

Sennheiser EK 500 G2 Manuel utilisateur

Sennheiser

Sennheiser EK 2020-D-II Manuel utilisateur

Sennheiser

Sennheiser EK 2000 Manuel utilisateur

Sennheiser

Sennheiser EK 300 IEM Manuel utilisateur

Sennheiser

Sennheiser Digital 6000 Series Manuel utilisateur

Sennheiser

Sennheiser EM 3732 COMMAND Manuel utilisateur

Sennheiser

Sennheiser EM 500 G2 Dimensions

Sennheiser

Sennheiser EK 2020-D Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur