Seneca Z-4RTD2-SI Manuel utilisateur

ORIGINAL INSTRUCTIONS

USER MANUAL

Z-4RTD2-SI

CONVERTER FOR THERMISTORS WITH 4 CHANNELS AND 24BIT ADC

SENECA S.r.l.

Via Austria 26 –35127 –Z.I. - PADOVA (PD) - ITALY

Tel. +39.049.8705355 –8705355 Fax +39 049.8706287

www.seneca.it

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 2

The content of this documentation refers to products and technologies described in it.

All technical data contained in the document may be changed without notice.

The content of this documentation is subject to periodic review.

To use the product safely and effectively, read the following instructions carefully before use.

The product must be used only for the use for which it was designed and manufactured: any other use is under

the full responsibility of the user.

Installation, programming and set-up are allowed only to authorized, physically and intellectually suitable

operators.

Set-up must be performed only after correct installation and the user must follow all the operations described in

the installation manual carefully.

Seneca is not responsible for failures, breakages and accidents caused by ignorance or failure to apply the

stated requirements.

Seneca is not responsible for any unauthorized modifications.

Seneca reserves the right to modify the device, for any commercial or construction requirement, without the

obligation to promptly update the reference manuals.

No liability for the contents of this document can be accepted.

Use the concepts, examples and other content at your own risk.

There may be errors and inaccuracies in this document that could damage your system, so proceed with caution,

the author(s) will not take responsibility for it.

Technical specifications are subject to change without notice.

Technical support

[email protected]

Product information

[email protected]

This document is the property of SENECA srl.

Copies and reproduction are prohibited unless authorised

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 3

Document revisions

DATE

REVISION

NOTES

AUTHOR

22/06/2022

First revision

10/10/2022

Added sampling rate

changes for fw 1010

revision.

Added info on float

swapped registers

Corrected errors in the

Modbus register list

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 4

TABLE OF CONTENTS

INTRODUCTION...........................................................................................................6

DESCRIPTION ..........................................................................................................6

COMMUNICATION PORT SPECIFICATIONS..........................................................6

TYPE OF SUPPORTED SENSORS.............................................................................7

RESPONSE MEASURES AND TIMES ........................................................................7

SAMPLING TIMES AND MEASUREMENT UPDATE TIME.....................................7

FILTER ......................................................................................................................8

MODBUS RESPONSE TIME.....................................................................................8

DEVICE CONFIGURATION..........................................................................................9

USB CONNECTION AND CONFIGURATION RESET.................................................9

FIRMWARE UPDATE.................................................................................................10

MODBUS COMMUNICATION PROTOCOL...............................................................11

SUPPORTED MODBUS FUNCTION CODES.........................................................11

MODBUS REGISTER TABLE....................................................................................12

NUMBERING OF "0-BASED" OR "1-BASED” MODBUS ADDRESSES ..............13

NUMBERING OF MODBUS ADDRESSES WITH "0-BASED" CONVENTION......13

NUMBERING OF MODBUS ADDRESSES WITH "1 BASED" CONVENTION

(STANDARD) ....................................................................................................................13

BIT CONVENTION WITHIN A MODBUS HOLDING REGISTER ...........................14

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 5

MSB AND LSB BYTE CONVENTION WITHIN A MODBUS HOLDING REGISTER

REPRESENTATION OF A 32-BIT VALUE IN TWO CONSECUTIVE MODBUS

HOLDING REGISTERS.....................................................................................................15

TYPE OF 32-BIT FLOATING POINT DATA (IEEE 754).........................................16

Z-4RTD2-SI: MODBUS 4X HOLDING REGISTER TABLE (FUNCTION CODE 3) 17

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 6

INTRODUCTION

ATTENTION!

This user manual extends the information from the installation manual to the configuration of the

device. Use the installation manual for more information.

ATTENTION!

In any case, SENECA s.r.l. or its suppliers will not be responsible for the loss of data/revenue or

consequential or incidental damages due to negligence or bad/improper management of the device,

even if SENECA is well aware of these possible damages.

SENECA, its subsidiaries, affiliates, group companies, suppliers and distributors do not guarantee that

the functions fully meet the customer's expectations or that the device, firmware and software should

have no errors or operate continuously.

DESCRIPTION

Z-4RTD2-SI is a converter for thermistors with four independent and isolated measurement channels equipped

with an analogue-digital converter with a 24-bit resolution.

The insulation relates to both the power supply and the RS485 communication port.

The device measures the value of the thermistors and makes them available through the RS485 port using the

Modbus RTU protocol.

COMMUNICATION PORT SPECIFICATIONS

RS485 COMMUNICATION PORTS

Number

Baudrate

From 2400 to 115200 bit/s configurable

Parity, Data bit, Stop bit

Configurable

Protocol

Modbus RTU Slave

USB COMMUNICATION PORT

Number

Protocol

Modbus RTU Slave

Use

For configuration with Easy-setup software and firmware update

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 7

TYPE OF SUPPORTED SENSORS

The supported sensors are:

SENSOR

STANDARD

MEASURING

RANGE

PT100

EN 60751/A2 (ITS-90)

-200 ÷ +650°C

PT500

EN 60751/A2 (ITS-90)

-200 ÷ +750°C

PT1000

EN 60751/A2 (ITS-90)

-200 ÷ +210°C

NI100

DIN 43760

-60 ÷ +250°C

CU50

GOST 6651-2009

-180 ÷ +200°C

CU100

GOST 6651-2009

-180 ÷ +200°C

Ni120

DIN 43760

-60 ÷ +250°C

NI1000

DIN 43760

-60 ÷ +250°C

Each channel is independent, therefore it is also possible to use different sensors in the 4 channels.

RESPONSE MEASURES AND TIMES

SAMPLING TIMES AND MEASUREMENT UPDATE TIME

The sampling time is configurable from 25ms to 400ms per channel.

SAMPLING TIME PER

CHANNEL

25 ms

50 ms

100 ms

200 ms

400 ms

for example:

By activating 4 channels and setting a sampling time of 100ms on all, you get a measurement update every:

100*4 = 400 ms.

By activating 2 channels at 25 ms and 2 channels at 100 ms you get a measurement update every: 25*2 + 100*2

= 250 ms.

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 8

ATTENTION!

In order not to lose the settings, NEVER update the firmware with a version older than the one installed

on the device.

FILTER

To each channel it is possible to insert a low pass filter to stabilize the measurement, it is a 10-sample moving

average filter.

MODBUS RESPONSE TIME

Modbus Response Time: 5 ms (typical)

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 9

DEVICE CONFIGURATION

The device can be configured using the Easy Setup or Easy Setup 2 software, configurations are as follows:

SENSOR TYPE: allows you to select the type of sensor connected to the channel, it is also possible to

disconnect the channel if it is not used.

UNIT OF MEASUREMENT: allows you to set whether the measurement must be in °C or in Ohm

3-WIRE MEASUREMENT: Allows you to set whether the sensor measurement will be carried out with 3 or 4

wires (for the 2-wire connection, refer to the 4-wire connection)

CHANNEL SPEED: Allows you to set the channel sampling time

IF CHARGE FAILURE: Allows you to replace (or not) the measured value with a temperature/resistance safety

value set by the user in the event of a fault. The failure can be caused by:

1) Sensor beyond measurement values

2) Sensor breakage

ACTIVATE FILTER: Allows you to activate the filter on the selected channel, filtering allows you to obtain a

slower but stable measurement.

INTERPRETATION OF FLOATING POINTS: It allows you to set whether the single precision (32 bit) Floating

Point registers are to be interpreted with the most significant value on the high word or on the low word.

USB CONNECTION AND CONFIGURATION RESET

The front USB port allows a simple connection to configure the device via the configuration software.

If it is necessary to restore the instrument's initial configuration, use the configuration software.

User Manual

Z-4RTD2-SI

PUBLICATION MAY BE REPRODUCED WITHOUT

PRIOR PERMISSION.

www.seneca.it

MI00584-1-EN

Page 10

FIRMWARE UPDATE

Through the USB port it is possible to update the firmware.

To update the firmware:

1) Disconnect the device from the power supply;

2) Holding down the firmware update button (positioned as shown in the figure), reconnect the device to

the power supply

3) Now the instrument is in update mode, stop pressing the update key and connect the USB cable to the

4) The device will be displayed in the PC as an "RP1-RP2” external unit

5) Copy the new firmware (uf2 extension) to the root of the "RP1-RP2” unit

Autres manuels pour Z-4RTD2-SI

Table des matières

Autres manuels Seneca Convertisseur de média

Seneca

Seneca S117P1 Manuel utilisateur

Seneca

Seneca S117P1 Manuel utilisateur

Seneca

Seneca Z109UI2 Manuel utilisateur

Seneca

Seneca Z Series Manuel utilisateur

Seneca

Seneca Z-SG3 Manuel utilisateur

Seneca

Seneca Z201-H Manuel utilisateur

Seneca

Seneca K109S Manuel utilisateur

Seneca

Seneca Z-8TC-SI Manuel utilisateur

Seneca

Seneca Z201 Manuel utilisateur

Seneca

Seneca Z-SG2-L Manuel utilisateur

Seneca

Seneca Z-SG2 Manuel utilisateur

Seneca

Seneca Z-SG3 Manuel utilisateur

Seneca

Seneca Z-SG Manuel utilisateur

Seneca

Seneca Z109REG-BP Manuel utilisateur

Seneca

Seneca R-KEY-MBUS Manuel utilisateur

Seneca

Seneca Z Series Manuel utilisateur

Seneca

Seneca Z204-1 Manuel utilisateur

Seneca

Seneca Z109REG-BP Manuel utilisateur

Seneca

Seneca ZC-SG Manuel utilisateur

Seneca

Seneca Z-4RTD2 Manuel utilisateur

Seneca

Seneca Z-SG Manuel utilisateur

Seneca

Seneca Z111 Manuel utilisateur

Seneca

Seneca K109UI Manuel utilisateur

Seneca

Seneca Z-SG Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur