4. Turn the terminal over.
5. Remove one side of the plastic protection film from the double-sided adhesive pad and carefully line the
pad up with the underside of the terminal.
6. Position the adhesive side of the pad onto the terminal and apply even pressure until it is fully adhered to
the terminal.
7. Remove the remaining plastic protection film, orient the terminal into position on the equipment, and attach
it.
8. Press firmly until the terminal is securely attached.
Warning!
General Cautions and Safety Warnings GlobalTRACS Lite System Quick Installation Guide
2MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION 80-JA506-1 Rev. C
General Cautions and Safety Warnings
Read these first! Before installing the GlobalTRACS Lite system, please read the following cautions
and warnings. It is highly recommended that these cautions and warnings are read and understood.
Not following them may compromise job safety.
In order to prevent injury or death, all machines equipped with the GlobalTRACS Lite system are
required to have the following warning labels (kit number 65-J5779-1) clearly fixed to the machine
according to the instructions.
These warning labels in no way supersede or allow deviation from the published requirements and
regulations found in “Title 30 of the Code of Federal Regulations (CFR).” Every operation should
conduct their own hazard assessments and meet all of the requirements of “Title 30 of the Code of
Federal Regulations (CFR)” to ensure safe operation in the storage, transportation, loading, and
blasting of explosives.
Warning!
Measure Continuity! It is critical that a good ground is established AND VERIFIED when
installing the GlobalTRACS Lite system, especially on battery-powered equipment. Both the
battery return (BAT_RTN) wire and the chassis ground (C_GND) wire on the GlobalTRACS
Lite system power/signal cable should be run to the negative side of the battery (BAT -) on battery-
powered equipment. Always verify a good ground by measuring with an ohm meter from the negative
battery terminal to where the ground wire will be attached. Continuity must be at 0 ohms. Always verify
0 ohms at both connections to ensure proper grounding is established.
Refer to all published equipment manufacturer cautions and warnings.
This machine is equipped
with a GlobalTRACS
terminal. Disconnect the
battery at the terminal
before performing electrical
maintenance or welding on
this machine.
Use of the battery disconnect
switch alone will not interrupt
power to the GlobalTRACS
terminal.
Failure to disconnect the
battery may create a shock
hazard and can cause
product damage, serious
injury or death.
15-J5773-1
Danger: This machine sends
radio frequencies that can
cause an explosion in an area
such as a blast zone, even
when power is off, resulting in
serious injury or death.
Do not transport, carry, store,
or operate this machine in an
area where the use of cellular
phones or radio frequency
devices can create an
explosion.
15-J5772-1
Warning!
General Cautions and Safety Warnings GlobalTRACS Lite System Quick Installation Guide
2MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION 80-JA506-1 Rev. C
General Cautions and Safety Warnings
Read these first! Before installing the GlobalTRACS Lite system, please read the following cautions
and warnings. It is highly recommended that these cautions and warnings are read and understood.
Not following them may compromise job safety.
In order to prevent injury or death, all machines equipped with the GlobalTRACS Lite system are
required to have the following warning labels (kit number 65-J5779-1) clearly fixed to the machine
according to the instructions.
These warning labels in no way supersede or allow deviation from the published requirements and
regulations found in “Title 30 of the Code of Federal Regulations (CFR).” Every operation should
conduct their own hazard assessments and meet all of the requirements of “Title 30 of the Code of
Federal Regulations (CFR)” to ensure safe operation in the storage, transportation, loading, and
blasting of explosives.
Warning!
Measure Continuity! It is critical that a good ground is established AND VERIFIED when
installing the GlobalTRACS Lite system, especially on battery-powered equipment. Both the
battery return (BAT_RTN) wire and the chassis ground (C_GND) wire on the GlobalTRACS
Lite system power/signal cable should be run to the negative side of the battery (BAT -) on battery-
powered equipment. Always verify a good ground by measuring with an ohm meter from the negative
battery terminal to where the ground wire will be attached. Continuity must be at 0 ohms. Always verify
0 ohms at both connections to ensure proper grounding is established.
Refer to all published equipment manufacturer cautions and warnings.
This machine is equipped
with a GlobalTRACS
terminal. Disconnect the
battery at the terminal
before performing electrical
maintenance or welding on
this machine.
Use of the battery disconnect
switch alone will not interrupt
power to the GlobalTRACS
terminal.
Failure to disconnect the
battery may create a shock
hazard and can cause
product damage, serious
injury or death.
15-J5773-1
Danger: This machine sends
radio frequencies that can
cause an explosion in an area
such as a blast zone, even
when power is off, resulting in
serious injury or death.
Do not transport, carry, store,
or operate this machine in an
area where the use of cellular
phones or radio frequency
devices can create an
explosion.
15-J5772-1
Warning!
General Cautions and Safety Warnings GlobalTRACS Lite System Quick Installation Guide
2MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION 80-JA506-1 Rev. C
General Cautions and Safety Warnings
Read these first! Before installing the GlobalTRACS Lite system, please read the following cautions
and warnings. It is highly recommended that these cautions and warnings are read and understood.
Not following them may compromise job safety.
In order to prevent injury or death, all machines equipped with the GlobalTRACS Lite system are
required to have the following warning labels (kit number 65-J5779-1) clearly fixed to the machine
according to the instructions.
These warning labels in no way supersede or allow deviation from the published requirements and
regulations found in “Title 30 of the Code of Federal Regulations (CFR).” Every operation should
conduct their own hazard assessments and meet all of the requirements of “Title 30 of the Code of
Federal Regulations (CFR)” to ensure safe operation in the storage, transportation, loading, and
blasting of explosives.
Warning!
Measure Continuity! It is critical that a good ground is established AND VERIFIED when
installing the GlobalTRACS Lite system, especially on battery-powered equipment. Both the
battery return (BAT_RTN) wire and the chassis ground (C_GND) wire on the GlobalTRACS
Lite system power/signal cable should be run to the negative side of the battery (BAT -) on battery-
powered equipment. Always verify a good ground by measuring with an ohm meter from the negative
battery terminal to where the ground wire will be attached. Continuity must be at 0 ohms. Always verify
0 ohms at both connections to ensure proper grounding is established.
Refer to all published equipment manufacturer cautions and warnings.
This machine is equipped
with a GlobalTRACS
terminal. Disconnect the
battery at the terminal
before performing electrical
maintenance or welding on
this machine.
Use of the battery disconnect
switch alone will not interrupt
power to the GlobalTRACS
terminal.
Failure to disconnect the
battery may create a shock
hazard and can cause
product damage, serious
injury or death.
15-J5773-1
Danger: This machine sends
radio frequencies that can
cause an explosion in an area
such as a blast zone, even
when power is off, resulting in
serious injury or death.
Do not transport, carry, store,
or operate this machine in an
area where the use of cellular
phones or radio frequency
devices can create an
explosion.
15-J5772-1
1. Route the power/signal cable from the GT300 to the designated vehicle power source.
2. Attach one 3-amp fuse to the power wire.:
• black BATTERY - one 3-amp fuse.
• white GROUND - no fuse required.
• violet INPUT - no fuse required.
• orange RUN_TERM - no fuse required.
Sendum Wireless Corporation!GT300 Quick Installation Guide
4
Practice extreme caution when wiring certain types of equipment, such as generators. Lethal voltages
can be present on certain types of equipment and can cause injury or death.
When working on battery-powered equipment, do not bring any type of flame, spark, etc., near the
battery. Gas formed while the battery is charging is highly explosive.This gas remains in the cells long
after charging has stopped. Do not lay metallic or conductive objects on the battery. Arcing will result.
Battery Capacitance. Due to capacitance voltages present in battery-powered equipment, whenever
performing maintenance which may prevent contact with bus bars and associated power cables, you
should discharge the capacitors following the recommended procedures written in the equipment
maintenance manual.
