SENAO CAP7250AG Manuel utilisateur

Quick Installation Guide

CAP7250AG/CAP7252AG/CAP7253AG

Wireless-AC+ABGN Long Range Ceiling Mount Dual Concurrent AP

Please verify contents of the box before continuing to set up the CAP7250AG/CAP7252AG/CAP7253AG.

CAP7250AG/CAP7252AG/CAP7253AG Access Point

12V/2A 100V~240V Power Adaptor

Mounting Bracket

Wall/Ceiling Mounting Hardware Kit

T-Rail Mounting Hardware Kit

*CAP7250AG is 3x3 concurrent 3x3 MIMO access point

*CAP7252AG is 2x2 MIMO internal ANT access point

*CAP7253AG is 2x2 MIMO external ANT access point

Connecting the CAP7250AG/CAP7252AG/CAP7253AG

1) Ensure that the computer in use has an Ethernet Card (RJ-45 Ethernet Port). For more information,

verify with User Manual.

2) Connect one end of the Category 5e Ethernet cable into RJ-45 port of the

CAP7250AG/CAP7252AG/CAP7253AG and the other end to the RJ-45 port on the computer that

will use the CAP7250AG/CAP7252AG/CAP7253AG. Ensure that the cable is securely connected to

both the CAP7250AG/CAP7252AG/CAP7253AG and the Computer.

3) Connect the Power DC Inlet to the DC-IN port of the CAP7250AG/CAP7252AG/CAP7253AG and

the Power to the electrical out.

Note: CAP7250AG/CAP7252AG/CAP7253AG supports both IEEE 802.3at PoE(Power over Ethernet) and

regular power adapter. You should use either one as the power source. Please do not apply both at the

same time.

IP address configuration

1) After ensuring the EnGenius device is powered on and plugged in, ensure that your computer is

on.

2) For the next steps, refer to your Operating System User Manual.

3) Once your computer is on, ensure that your TCP/IP is set to On or Enabled. (In the control panel,

double click Network Connections and then double click on the connection of your Network

Interface Card (NIC). Select Internet Protocol (TCP/IP) and then click on the Properties button.)

4) If your PC is already on a computer network, ensure that you have set it to a Static IP Address on

the interface (or Ethernet card that will use the CAP7250AG/CAP7252AG/CAP7253AG) as

192.168.1.21 and the Subnet Mask address as 255.255.255.0. (Select Use the following IP

Address radio button). Once the computer has been prepared, proceed to setting up the

CAP7250AG/CAP7252AG/CAP7253AG.

CAP7250AG/CAP7252AG/CAP7253AG Setup

1) To configure CAP7250AG/CAP7252AG/CAP7253AG, open a web browser (example: Microsoft

Internet Explorer, Mozilla Firefox, Google Chrome, etc.).

2) In the address bar of the web browser, enter 192.168.1.2 (the default IP address of the

CAP7250AG/CAP7252AG/CAP7253AG)and hit enter.

3) A login screen will appear. By default, the

username of the

CAP7250AG/CAP7252AG/CAP7253AG is

admin and the password is admin. Enter the

current username and password of the

CAP7250AG/CAP7252AG/CAP7253AG and

then click Login. Refer to the

CAP7250AG/CAP7252AG/CAP7253AG user

manual on how to change the username and

password.

4) After clicking Login with the correct username

and password, the

CAP7250AG/CAP7252AG/CAP7253AG Main Menu will appear. If you are successful, proceed to

setting up the wireless connection.

http://192.168.1.2

Switching Between Operating Modes

This device can operate in the following modes: Access Point, WDS AP, WDS Bridge and Repeater.

A. Click on the Operation Mode link under the System navigation drop-down menu.

B. Operating Mode: Select an operating mode from the list (Access Point, WDS AP, WDS Bridge or

Repeater) and then click on the Apply button.

C. All basic setup is completed. Note: The wireless connection is not secure. To setup security on the

CAP7250AG/CAP7252AG/CAP7253AG, refer to the CAP7250AG/CAP7252AG/CAP7253AG User

Manual.

Mounting the CAP7250AG/CAP7252AG/CAP7253AG

Using the provided hardware, the CAP7250AG/CAP7252AG/CAP7253AG can be attached to a ceiling or

wall.

To attach the CAP7250AG/CAP7252AG/CAP7253AG to a ceiling or wall using the mounting bracket:

1) Attach the mounting bracket to the wall or ceiling using the provided wall/ceiling mounting

hardware kit.

2) Insert the provided short screws into the bottom cover of the

CAP7250AG/CAP7252AG/CAP7253AG.

Leave enough of the screws exposed to ensure that the unit can be attached to the mounting bracket.

If extra space is required, use the provided spacers and long screws from the T-Rail mounting

hardware kit to increase the space between the unit and the mounting bracket.

3) Mount the CAP7250AG/CAP7252AG/CAP7253AG on the mounting bracket by rotating the unit

clockwise about 90 degrees to secure it in place.

To attach the CAP7250AG/CAP7252AG/CAP7253AG to a ceiling using the provided T-rail

connectors:

1) Attach the T-rail connectors to the bottom cover of the CAP7250AG/CAP7252AG/CAP7253AG

using the provided short screws.

Two sizes of T-rail connectors are included in the mounting hardware kit: 15/16in (2.38cm) and 9/16in

(1.43cm).

If extra space is required to accommodate drop ceiling tiles, use the provided spacers and long screws.

2) Line up the connected T-rail connectors with an appropriately sized rail and press the unit onto

the rail until it snaps into place.

Note: To protect your CAP7250AG/CAP7252AG/CAP7253AG, use the Kensington security slot to attach a

cable lock (cable lock is not included).

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Country Code selection feature to be disabled for products marketed to the US/CANADA

Professional installation instruction

1. Installation personal

This product is designed for specific application and needs to be installed by a qualified

personal who has RF and related rule knowledge. The general user shall not attempt to install

or change the setting.

2. Installation location

The product shall be installed at a location where the radiating antenna can be kept 20 cm from

nearby person in normal operation condition to meet regulatory RF exposure requirement.

3. External antenna

Use only the antennas which have been approved by the applicant. The non-approved

antenna(s) may produce unwanted spurious or excessive RF transmitting power which may

lead to the violation of FCC limit and is prohibited.

4. Installation procedure

Please refer to user’s manual for the detail.

5. Warning

Please carefully select the installation position and make sure that the final output power does

not exceed the limit set force in relevant rules. The violation of the rule could lead to serious

federal penalty.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SENAO Point d'accès sans fil

SENAO

SENAO WAP7301AG Manuel utilisateur

SENAO

SENAO OAP8250AG Manuel utilisateur

SENAO

SENAO NL-5354AP1 Aries2 Manuel utilisateur

SENAO

SENAO SL-2511BG PLUS Manuel utilisateur

SENAO

SENAO IAP8250AG Manuel utilisateur

SENAO

SENAO CAP2100AG Manuel utilisateur

SENAO

SENAO 2511BG2 PLUS Manuel

SENAO

SENAO IAP8350AG Manuel utilisateur

SENAO

SENAO OAP7250AG Manuel utilisateur

SENAO

SENAO NOA-3570 Manuel utilisateur

SENAO

SENAO ECB-3610-S Manuel utilisateur

SENAO

SENAO NL-2611CB3 PLUS Manuel utilisateur

SENAO

SENAO ECB7510 Manuel utilisateur

SENAO

SENAO SL-2511AP2 PLUS Manuel utilisateur

SENAO

SENAO OC1650 Manuel utilisateur

SENAO

SENAO SL-2011CD-GP Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur